Search Documents

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By Licheng Zhou

The use of aquatic plants for the removal of heavy metals from wastewater has gained high interest. In this study, batch experiments were conducted to evaluate the adsorption of copper ions in aqueous solution by P. pectinatus L. under various conditions of contact time, initial pH of the solution, metal concentration and adsorbent dosage. The results showed that the maximum adsorption amount of copper ions by P. pectinatus L. was 22.60 mg/g when the initial copper ions concentration was 98.41 mg/L at pH 4.5. The Langmuir and Freundlich models were used to describe the adsorption equilibrium of copper ions on P. pectinatus L. and the adsorption followed the Langmuir isotherm. The adsorption kinetic was well-fitted with pseudo-second-order sorption equations.

Jan 1, 2009

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By J Fisher, M Castro, A Hariyadi

The train haulage system being designed for PT Freeport Indonesia’s Grasberg Block Cave (GBC) will be located within the mine at an elevation of almost 3000 m above sea level on the west side of the island of Papua, Indonesia. The developing block cave is beneath the active Grasberg Open Pit and will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing plants. The design entails 28 km of rail and 119 ore chutes, which will be brought online over the course of ten years.The train haulage system will be driverless and fully automated. Sequentially, the system includes remote controlled rock breakers at the top of the chute grizzlies, followed by remote controlled chute loading of the trains, then autonomous train haulage and autonomous unloading. An overhead catenary system (OCS) will power the locomotives, which are equipped with on-board batteries to drive through the loading and unloading sections. Service locomotives with drivers move material-laden freight cars in and out of the service shaft, destined for workshops, the magazine and batch plants. Service locomotives are also used for haulage level maintenance. Highly reliable and redundant control and communications systems are required to manage 12 trains in simultaneous operation.This paper provides an overview of the train haulage system’s technical complexities and the associated support systems interactions. The paper also highlights the project management issues and successes of this globally sourced project.CITATION:Hariyadi, A, Castro, M and Fisher, J, 2016. Automated train ore transport, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 563–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Zajber A, Kulchen R, Letzel D, Weyer A, Schwellenbach J

The search for modem casting plant concepts today focuses more and more on the harmonisation and optimisation of overall concept lines to obtain a continuous quality control and reduce the cost of production (Figure 1). Fin I As far as continuous casting plant concepts are concerned, this specifically requires an optimal adaptation and flexible operation when converting liquid steel into a directly processable product without any in-between treatment. Continuous casters need to fully satisfy the requirements of both the upstream steelmaking facilities as well as the downstream rolling facilities.

Jan 1, 1999

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By P. Fauvel, V. Nasri

In January 2001, French and Italian governments signed an agreement for the construction of a new Lyon-Turin railway line. This project includes a tunnel of 53.1 km length and a maximum of 2500 m overburden to be designed for a reference speed of220 km/h. The tunnel crosses major part of the West Alpine geological formations, which are very complex and contrasted in terms of the nature of rocks and the mechanical and hydrogeological conditions. In addition to the twin single-track tubes, numerous intermediary shafts, security station and intervention sites and cross passages should be built to respond to the security, operational and construction requirements. This paper describes the results of the preliminary engineering design and multiple challenges of this very long and deep railway tunnel.

Jan 1, 2005

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By L. A. Cramer

South African platinum mines produce the world?s majority of platinum metal that is used in autocatalysts and jewellery. As the platinum market is forecast to grow at healthy rates into the future, the South African producers, Anglo Platinum, Impala, Lonmin and Northam, are planning to expand in the next decade. Furthermore, a number of smaller producers who are accessing other mineral rights are entering the buoyant market. The South African platinum mines have traditionally exploited the Merensky Reef of the Bushveld Igneous Complex (BIC); however, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the orebodies at deeper levels. In the past decade all of the producers have begun to mine the less attractive UG2 reef because of its cheaper mining costs. This UG2 reef contains significant quantities of chromite with typically a chrome-to-iron (Cr/Fe) ratio of 1.35. UG2 ores can contain between 10 and 25% Cr2O3dependingupon the reef width and the selected mining method. It is relatively cheap and easy to extract a portion of the chromite from a platinum concentrator tailings stream at a grade of between 40?42% Cr2O3. However, it is only in recent years that some ferrochrome producers have begun to source some of their chromite from the tailings of platinum producers. South Africa is also the world?s largest single producer of ferrochrome and supplies much of the world?s stainless steel producers and thus the growing market for their product. As the traditional sources of high Cr/Fe ratio ores have been depleted at the shallow economic depths and thus have become more expensive sources of chromite, technical developments have improved the ability to use fine chromite economically to make acceptable grades of ferrochrome. Thus UG2 fines are now becoming possible cheap sources of acceptable feed to the ferrochrome industry. The abundance of feedstock for ferrochrome production and the lessening dependence on mined material will impact upon the structure of the ferrochrome business in South Africa. With continued platinum mining from UG2 reefs, South Africa is set to remain highly competitive in the world?s ferrochrome/stainless steel industry.

Jan 1, 2004

By McKenzie A. M

The Corridor ore body is so named because it occurs in an east-west zone or corridor of schist bounded on the north by the siliceous conglomerates of Mount Lyell, and on the south by similar conglomerates of the Tharsis ridge (Fig. 1). It was discovered after the geophysical prospecting methods described below had defined a target zone for diamond drilling.Since the proving of copper mineralisation by drilling, the corridor orebody has served the vital function of a convenient known target body for the orientation of more recently developed geophysical methods. Traversing of the orebody by these new methods has provided experience for the evaluation of anomalies elsewhere.Some of the methods applied had not been used in Australia before, and were introduced to the west coast of Tasmania through the undertaking there of modern regional exploration programmes. The authors feel that the information gained could be of assistance to others engaged in geophysical prospecting.HISTORY OF DISCOVERYProspecting in the Mount Lyell district has been more or less continuous since 1881. The first geological report was published by Thureau (1886).In 1934, Blazey and Douglas (1934-38) commenced geophysical surveys at Mt. Lyell using the equipotential method.They obtained anomalous indications in several discrete zones and actually detected the south-east half of the corridor orebody but their work never became the basis for...

Jan 1, 1961

By F. Essrich

A quantitative rockburst hazard assessment procedure was introduced on Elandsrand Gold Mine at the end of 1994. It is currently used to evaluate the seismicity-related risk in production areas on the mine. Six parameters related to seismicity, geology, mining layout, and production are rated and results are used as a planning tool on a regular basis. The applied assessment can be considered successful in that it promotes awareness of the seismic hazard and provides an opportunity to address seismicity-related mining problems. A comparison between high risk panels and those working areas with rockburst incidents showed that high hazard ratings reliably forecast the occurrence of larger events in the following month but they do not necessarily predict those working places with rockburst-related accidents. From this one may conclude that high levels of seismicity do not coincide with high rockburst rates.

Jan 1, 1997

Background geochemistry of streams in mineralised terranes is affected by (a) natural sulphide oxidation and associated metallic discharges; and (b) previous mining history and associated discharges. Both of these processes elevate background metal concentrations by (i) directly adding dissolved metals to stream water; and (ii) adding sulphide-bearing sediments' to the stream system, to be trapped in old channels and bars for later chemical decomposition in situ or after flood reworking. Definition of downstream geochemical background, involving sediments and low-flow dissolved chemistry prior to mining is prudent, as this will provide a benchmark for any required estimation of new inputs from, for example, accidental tailings discharges. Two high-profile examples from western USA illustrate these points. Summitville mine in southern Colorado is an environmental disaster left when the operating company went bankrupt in 1991. Acid metal-rich discharges are leaving the site into a river system used for agricultural irrigation. However, nearby sub-catchments have substantial naturally occurring acid metal-rich discharges and locally discharge natural sulphide-rich debris flows into the same river. Distinction between natural and anthropogenic pollution in the downstream reaches is difficult. Early mining at Cooke City, Montana (New World District) released large volumes of sulphide-bearing tailings into the river system when a tailings impoundment dam failed. The event was equivalent to a 100-year flood, and tailings were deposited for 30 km downstream. These tailings are currently oxidising, and are being reworked into the modem stream during high flow events, thus perturbing background geochemistry.

Jan 1, 1999