Search Documents

By R. M. Lamya

The leaching behaviour of nickel?copper matte in an acidic?copper sulphate solution during the repulping stage at Impala Platinum Refineries has been studied. The base metal recovery process consists of a matte repulping stage prior to a series of pressure leach stages. Therefore, the repulping stage is basically an atmospheric leach stage in which the matte containing mostly Niand Cu is leached in copper-spent electrolyte from the tank house, resulting in dissolution of nickel and precipitation of almost all the copper. To understand the nature of the leaching process during this stage of the operation, the effects of temperature stirring rate and matte particle size on the rate and extent of base metal dissolution and copper rejection from the solution have been investigated. The leaching mechanism of the matte in the investigated system is alsoproposed.

Jan 1, 2006

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D. Gendzwill, N. Martin

"In early 1987, the Patience Lake potash mine near Saskatoon, Saskatchewan, was closed due to uncontrollable floodingWater inflows were first encountered during routine mining in 1975 at the south boundary of the mine lease. Underground grouting and construction of bulkheads limited the flo but did not completely stop it. Subsequent seismic surveys showed that the mine had approached the edge of a large collapse structure in which the salt and potash had been partly dissolved and removed by groundwater.In 1986, the small flow into the mine started to grow. Despite renewed grouting, the flood increased and outstripped pump capacity. The grouting program temporarily slowed the inflow but was unable to stop it. Eventually, from seismic and drilling evidence, it became clear that the water source was an extensive system of vertical fractures which would be impossible to seal by drilling and grouting from underground. A new plan to install 14 bulkheads underground would have sealed the water source from the rest of the mine but the construction program could not be completed before rapidly increasing inflow threatened to fill the mine. The underground mine was closed and a new solution mine started in 1988."

Jan 1, 1996

Grade control is a real challenge, and better sampling and modelling practices are among the tools that have proven efficient in improving it. Although based on rather trivial examples, this paper addresses the following important issues: How much of a challenge is it? How and to which degree can it be improved? And what kind of economic benefits should be expected in return for the corresponding efforts?

Jan 1, 1999

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By E. D. Gardner

"Trolley lines used in connection with electric haulage in mines are a source of danger and many lives have been lost by men accidentally coming in contact with the wires. Usually the wires in metal mines are sufficiently guarded to prevent men from touching them with their person or by pieces of steel which they may be carrying or their shoulders, while walking along the level. However, it is difficult to guard effectively the wires at loading chutes along the haulage ways and in spite of safe guards, chute tappers have been electrocuted through loading bars accidentally touching the trolley line.To overcome this danger the Calumet & Arizona Mining Co., at Lowell, Arizona formely used a hinged V-shaped trough made of 1-inch by 6-inch lumber, that was dropped over the wire in front of the chute, when the cars were being loaded. This arrangement interfered with the easy operation of the chute, and a cut-out device for the trolley line was devised by W. R. Gibson, chief electrician for the company. This cut-out is efficient easily constructed and roes not interfere with the operations at the chutes or with the motors operating on the same level.When the cut-out is open the electric current is carried past the gap by an insulated wire on the opposite side of the drift. A hinged board drops down over the ends of the trolley guard when the slide is open and Prevents anything touching the live wires. About ninety of these cut-outs are now in use in the mine,The levels under the scopes are timbered with drift sets placed 5 feet apart, and the loading chutes take up the space between two sets. All trolley wires in. the company's mines are carried 6 feet above the rails and guarded by two 1/2 by 6-inch boards placed on either side of the wire."

May 1, 1921

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By WU Jian-hui

Keywords: metallic material, precursor synthesis, precipitation, nickel, fibrillar powder The composition and morphology of the precursor of fibrillar nanocrystalline nickel powder prepared by oxalate precipitation are characterized by XRD,IR and SEM analysis, and the effects of temperature, nickel concentration, pH, surfactant and drying process on the morphology and the dispersion of the precursor are investigated. By the experiment results, the fibrillar precursor is a complicated nickel salt. The precursor prepared in the of 60~70°C,0.6~0.8 mol/L nickel ion, pH=8.4~8.6 and with addition of PVP surfactant is well dispersive and in fiber form. The powder dried by azeotropic distillation is dispersive.

Jan 1, 2005

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

Paiam is a new township in the high mountains of Papua New Guinea built in association with the Porgera Joint Venture mine, one of the world's largest and most remote open cut gold mines. The Paiam town project is an interesting and genuine attempt at building sustainability into a community associated with a mine. A result of a tri-party agreement between a resource developer, government and land owners, this town is a good example of appropriate utilisation of benefits, obtained from resource development, directed at achieving a sustainable environment at local and regional levels.   Mining brought technology and income to the region, although as most mine staff fly directly in and out, local landowners considered there was a limited flow of benefits within the nearby townships. An agreement with government and mine was reached that more mine personnel and their families be housed locally. In 1998, we, a firm of Landscape Architects and Heritage Consultants based in Cairns, Queensland, were engaged to assist develop the fledgling town of Paiam into a livable and sustainable town and to produce material that would convey that information to stakeholders.   The design focused on establishing a sustainable town, with livability, urban form, aesthetics and opportunities for economic, social and cultural development. Aiming to be a livable town for locals and mine staff it included a market place designed as a focus for town life, essential for social cohesion and economic opportunities.   Located at 2200 m on steep rainforest clad topography, the town development has been laid out using an appropriate urban form based on organic village layouts. Clusters of houses allow for a common public area so children's play is monitored assisting with a sense of community similar to a traditional defensible village. Aesthetical consideration helps in developing community pride whilst maximising potential for development of a tourist industry.   Opportunities for ongoing economic development were incorporated in the design and construction process. These included developing skills and trades to service the region and to provide skills, development, income opportunities and infrastructure to last beyond mine closure. Administration procedures were set in place to form the basis of good governance.   The shift from traditional subsistence lifestyle to a sustainable community with traditional attributes was the project's goal and is being achieved.

Jun 1, 2010

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

Formation of either sodium jarosite or lead jarosite from concentrated chloride solutions containing small concentrations of sulphate has been demonstrated. Sodium jarosite is precipitated at 95-100°C from FeC13-FeCI2-NaCI-PbCI2 solutions to which was added Na2SO4 or Li2SO4 in amounts greater than 0.05 M. In the absence of alkali metal ions capable of forming jarosites, lead jarosite was precipitated from either FeCI3-PbCI2 or FeCI3-FeCI2-LiCI-PbCI2 solutions to which had been added small amounts of sulphate. Many of the factors affecting jarosite precipitation from chloride solution have been elucidated, and the most critical were sulphate concentration and initial pH. Concentrations of HCI in excess of O. I M essentially suppressed the production of jarosite in chloride media. Alkali jarosite, precipitated in the presence of dissolved lead, incorporates a small amount of this metal into the alkali jarosite lattice. Small but significant amounts of copper can also be incorporated into alkali jarosite and the amount is further increased in the presence of lead. Other divalent base metals such as Zn, Cd or Ni are not significantly precipitated. Sulphate control in either FeCI3 or FeCl3-NaCI leaching systems could likely be maintained by jarosite precipitation provided that the acid concentration of the solution was low.

Jan 1, 1981

By Kray Luxbacher

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

Jan 1, 2007

By G. L. Smith

The fundamental challenge facing mineral and metal companies is how to create sustainable value while operating within mandated strategic bounds, identified constraints, and variable market and economic conditions. This can be achieved by allowing the fixed physical nature of the mineral asset to drive definition of the optimal technical solution to mining and processing activities, and developing and resourcing a strategically aligned portfolio of production entities that creates flexibility to near- and longer-term business environment shifts, i.e. a production mix that allows variation of output to respond to short term market variation, within a long term context. The practical achievement of this outcome is enabled by the concept of strategic long term planning. The core elements of strategic long term planning in the metals and minerals industry, and the relationship between them, are expanded. The strategic long term planning framework is a logic construct that enables delivery of an optimized, strategically-aligned business plan from the mineral asset portfolio using a set of tools and techniques with a common language, standards, systems and processes to align decisions and actions on a cyclical basis.

Jan 1, 2012

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs. A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanised mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximised, cost if reduced and all profit opportunities are optimised. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

For the first time in its history, the George A. Fox Conference let its focus venture away from the friendly confines of the East Coast of the United States to spend part of the one-day conference looking at projects from around the globe. With a record-setting attendance of 377 people, the conference, titled ?Tunneling: An international perspective,? opened with a keynote speech from special guest In-Mo Lee, professor, Korea University in Seoul, South Korea. He is also the president of the ITA-AITES. In a sweeping presentation, Lee walked the packed audience through some of the most fascinating and challenging projects in his home country. Among the projects he spoke about were Korea?s longest railway tunnel, the Solahn Tunnel and the Inje Tunnel, a freeway tunnel that is 11.94 km (7.4 miles) long.

Jan 1, 2012

In addressing the need for non-degree tertiary training, let us examine some recent reviews of engineering and geoscience education. The Finniston Report (1) criticised the formation of engineers in the UK and stated that this was largely due to the narrow British conception of engineering as a branch of applied science which militates against an effective marriage between theory and application. It also criticised the system for not giving students sufficient grounding in the synthesis of technical, human and financial considerations within their undergraduate courses. As we all know, this report has led to the restructuring of engineering education in the UK. More recently, a Review of the Discipline of Engineering was carried out in Australia by a committee chaired by Professor Sir Bruce Williams (2). The report stated that: Australia has a fairly good system of engineering education that should be made better. more should be done to develop the communication skills of both staff and students. more attention should be paid to changes in engineering practice and the human element in technology. there is a serious shortage of state of the art equipment in most engineering schools. female enrolments in engineering courses should be increased from the current level of about 7% to 20% by 1997. employers should develop a better understanding of the need for continuing education. staff in engineering schools should develop closer relations with employers of engineers. higher education institutions with engineering schools should give financial and other inducements to staff to increase the proportion of study leave or professional development leave spent working as engineers in the business sector. there is considerable room for improvements in the teaching process and in the development of evaluation schemes for assessing the teaching contributions of staff. In its recent report to the Council of the Institution of Engineers, Australia, the Task Force on Engineering Education(3) makes the following points: managerial, entrepreneurial, professional and interpersonal skills should be introduced and integrated into the undergraduate courses but studied in depth as part of continuing education. the continuing education policy of the Institution should be promoted and strengthened with all engineers required to pursue continuing education. the Institution should develop a comprehensive guide to continuing education available from universities, colleges and other public and private sector organisations.

Jan 1, 1989

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006