Search Documents

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By Walter Smith

Environmental Quality Committee ?EQC was created in 1995 to facilitate dialogue between industry and northern communities and help build the understanding of the industry in those communities. ?EQC is made up of representatives from 32 northern communities. ?Meet regularly with Cameco to discuss on going and new projects. ?Tour mine sites on a yearly basis.

Nov 1, 2011

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country's economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world's more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By J. M. Davidson, F. Fraas, J. E. Conley

"A number of Reports of Investigations pertaining to the extraction of potash from cal¬cined polyhalite have been made by various members of the Nonmetallic Minerals Experiment Station of the United States Bureau of Mines. These reports describe results obtained in the study of samples of polyhalite (2CaS04.K2S04.MgS04.2H20) from deposits of possible com¬mercial importance in Texas and New Mexico.3Storch and Clarke6 in their initial paper presenting data on the properties of Texas polyhalite demonstrated the desirability of calcination and subsequent hot extraction with water as a satisfactory pronedure for treatment of this potash-bearing salt. Their preliminary data have been supplemented by an additional report7 dealing more particularly with the leaching of raw and calcined polyhalite with water and with saturated sodium chloride solu¬tions. Further data8 have been reported as a result of experiments made in a small labora¬tory rotary-tube furnace under various calcination and extraction conditions. Hot water was used as the leaching solution in all of these tests.In addition to the data on calcination and extraction, two processes as proposed by Storch and Clarke have been published by Wroth,9 and more recently a number of very promising processes have been proposed by Storoh and Fragen.10"

Apr 1, 1932

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By D Wyatt, J Domenico, W Kow

Over the past few years developments in heavy minerals processing have concentrated on the mineral separation portion of the business. The best example of this would include new developments in rare-earth magnetic separators and associated flowsheet modifications. Except for some minor modifications in spirals, the æwetÆ side of the separation business has lagged behind the ædryÆ side. Basic concentrator design has not changed in 20 years. Recent pilot trials by Outokumpu Technology have shown the benefits of a new gravity flowsheet that combines density separation and spiral concentration on a variety of heavy mineral deposits. This concept is already well utilised within the iron ore industry. The synergistic combination of these two technologies allows smaller, simpler, and controllable gravity concentrators to be built while providing equivalent or better grade and recoveries of valuable heavy mineral. This is contrasted to the all spiral flowsheet characterised by the diminishing returns of multiple stages of spirals and associated recirculating loads. Examples of the flowsheets and associated benefits will be presented from a variety of cases.

Jan 1, 2001

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

By R. Gallinger

In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale. The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP?s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed as sufficient justification for the formation of INAP. INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage. This paper will explore the international efforts and activities of INAP

May 1, 2005

By F. M. C. C. Vieira

The work described forms part of a Safety in Mines Research Advisory Committee (SIMRAC) funded project, currently an ongoing programme of research aimed at providing ?improved criteria, guidelines and the use of numerical models to design mine layouts at depth, so as to reduce seismicity and enhance worker safety?. The entire project deals with a number of distinct, albeit interrelated, research areas such as: subsidence and caving in hardrock, general numerical criteria for layout design, regional benefits of backfill, concrete pillars, strike stabilizing pillars and bracket pillars. This paper will focus on the last two items only. New considerations for the design of both stabilizing pillars and bracket pillar layouts are briefly discussed.

Jan 1, 1998

By Hugo Noriega

El objetivo del presente texto es establecer un programa de compensación para el personal de la compañía a través de una adecuada administración sistemática y equitativa de sueldos, que facilite el control de gastos para la gerencia y a su vez, desarrolle la confianza en el personal empleado. Por tal motivo, se determinaron cuatro objetivos en la política de suedos: Se busca pagar un sueldo normal por trabajo similar bajo condiciones semejantes, mantener la estructura de sueldos dentro de la tendencia de la localidad, reconocer el mérito individual y controlar los sueldos dentro de los límites determinados. Asimismo, el programa comprende un plan de sueldos que incluye: plan de análisis de puestos, evaluación, pago, administración y de comunicaciones. Una vez puesto en funcionamiento y con los beneficios realizados, se confirma que no hay un reclamo colectivo de suedos. Por consiguiente, el plan es sometido a análisis críticos de la gerencia, con el objetivo de ganar su aceptación y obtener uniformidad en los criterios.

Jul 20, 1959

Tougher physical mining and processing conditions as well as economic circumstances are causing many mining companies to re-evaluate the effectiveness of their mine planning. The recent wave of inexpensive computing power provides the engineer an opportunity to go beyond the simple one-off manual mine design and production schedule. The basis of a good mine plan is a good reserves model. Concepts of mine model development are explored. The only advanced computer methods that have found consistent success in optimising mine planning functions are economic pit limits determination and material scheduling. Three pit 'optimisation' methods are examined; the moving cone, the Lerchs-Grossman 3-D graph algorithm, and the new network flow algorithm. A comparison between the methods in terms of total profits generated and computer time involved are made. The results show that both algorithms produced a higher profitability than the simple moving cone, but at much higher execution times. However, the profit increase never exceeded much more than 1 % of the base moving cone case. Finally, a method for the development of long range material production schedules with forward waste planning is presented.

Jan 1, 1989

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By D. H. Horswill

The Red Dog Mine is the world’s largest zinc mine. It is located 145 km (90 miles) north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called the Northwest Alaskan Native Association (NANA) Development Corp. NANA acquired surface and subsurface title to this resource as part of its settlement lands under the Alaska Native Claims Settlement Act. In 1982, NANA entered into a lease agreement with Cominco. Cominco is an international mining company focused on zinc. It built and operates the Red Dog Mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language and traditions are as important to the NANA people today as they were in the past.

Jan 1, 2000

By L Maw

New ZealandÆs largest gold producersÆ OceanaGold Macraes Mine is characterised by a large tonnage and relatively low grade operation. To survive in diminishing real gold prices, the operation must focus on a culture of continuous improvement. This paper presents the outcome of a supplier sponsored continuous improvement project known as the Orica Advanced Mining Services project.   In March 2004 OceanaGold (then GRD Macraes) entered into an Advanced Mining Services (AMS) project with Orica Mining Services. The motivating factor behind OceanaGoldÆs need to improve bulk waste productivity and SAG mill throughput was the planned increase in production from five million to 5.4 million tonnes per annum. A stripping ratio of ten to one meant that optimisation of the drill, blast and production functions was paramount.   The primary focus of the project was to optimise the drill and blast parameters to suit the variable rock conditions throughout the mines main operating pit (Frasers Pit). Fragmentation of the ore for presentation at the SAG mill, and cost reduction on the mining of bulk waste movement, were the primary objectives. A number of additional initiatives complimenting the interface between drill, blast and ore production were also established. These included; +        reduced ore loss through delineation of ore boundaries to allow for blast movement; +        established blasting parameters for variable geological conditions, resulting in improved fragmentation; and +        improved asset utilisation by establishing a blasting regime that angled grade control holes to be used as blastholes in the stockworks area.   A year into the project, the philosophy of continuous improvement is now in-grained at the Macraes minesite. As the project continues, the focus is on the further refining of those procedures established, to ensure a continued focus on lower unit mining production costs.

Jan 1, 2005