Search Documents

The Hyde Macraes Shear Zone (HMSZ) is an extensive low angle semibrittle mineralised structure in the Otago Schist Belt, New Zealand. The shear zone is located on the lower limb of a late metamorphic recumbent fold. Structural observations suggests that the shear zone initiated as a high strain mylonite zone and transgressed the ductile/brittle boundary (D4) later in its development. A surge zone at Round Hill is bounded to the south by a NE-SW striking lateral ramp which displaces the hanging wall shear (HWS) by 50 m. Oblique strike slip displacement during surge zone propagation created space for deposition of the sheeted vein complex or stockwork. Quartz recrystallisation in stockwork veins suggests that the veins were deformed in a ductile manner and implies that surge zone propagation may have occurred during late D3 deformation. A macroantiform was produced during D3/D4 shortening below the HWS. Over tightening of the antiform hinge created SW and NE-dipping ramp thrusts. Continued strike slip displacement along the lateral ramp rotated the antiform and associated ramps into a south plunging drag fold. Post-mineralisation (D5) structures include NE-dipping nonna! faults below the HWS and SW-dipping low angle imbricate thrusts above the HWS. The development of these structures was kinematically compatible with normal movement on the HMSZ and is related to mid Cretaceous break up of Gondwanaland in the SW Pacific.

Jan 1, 1992

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

Significance of the body of iron oxide, which in part overlies as its hanging-wall the rich chalcocite ore-body at Mount Oxide, Queensland, has been variously interpreted by engineers and geologists who have inspected the deposit.Among the interpretations offered is the one that the body represents the residual of an original medium to low grade...

Jan 1, 1939

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By B A. Mowat, T M. Leach

The Morobe Goldfield inPapua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23 t) and Edie Creek (4 t) and geological resources have been established at Hidden Valley (78 t), Kerimenge (36 t) and Hamata (30 t).Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.   It is proposed that magmatic fluids which evolved from parent melts to the high level Edie porphyry stocks mixed with convecting meteoric fluids and were channelled along major structure and diatreme contacts. Proximal to the intrusives, gold mineralisation is associated with deposition of pyrite-hematite-quartz+/-magnetite-gold (Hamata) and pyritebasemetals-quartz-gold (Wau). The mineralising fluids were hot, and periodically saline due to pulses of magmatic fluid. Gold is non-refractory and occurs as 20 to 30 micron blebs within the pyrite.   More distal from the intrusives or under late cooler conditions, mixing of cool dilute meteoric and magmatic fluids resulted in gold deposition associated with arsenic rich pyrite-and arsenopyrite-mineralisation (Kerimenge, Hamata and Edie Creek). Gold is refractory and occurs within the sulfides either as sub-micron inclusion or within the lattice.   CO2 and H2S gases which evolved off the upwelling hydrothermal fluids as a result of boiling and pressure reductions, condensed within superficial groundwater and formed cool oxygenated bicarbonate fluids. These fluids percolated back down the structures depositing manganocarbonate in the upper parts of the hydrothermal system. At deeper levels in the system mixing of the descending bicarbonate fluid with upwelling mineralised fluids deposited manganocarbonate-quartz-sulfides nonrefractory gold (Hidden Valley, Wau and Edie Creek).   At Kerimenge the cool bicarbonate fluids have also quenched a late stage magmatic fluid rising along high permeability structures. The quenching has resulted in deposition of non-refractory gold mineralisation associated with hessite (Ag2Te)-tennantite-chalcopyrite deposition.   Within the Morobe Goldfield, a transition from deeper level pyrite-quartz+/-hematite-magnetite to intermediate level quartz sulfide and quartz-carbonate-sulfide deposition to upper level, massive manganocarbonate deposition is recognized. Gold mineralisation can occur within all levels up the system.

Jan 1, 1995

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

A study of drilling data at various stages of development of an orebody show that the semi-variogram, used for calculating the accuracy of block estimates can be ill-defined if too few data are available. The consequencesin this case are to have blocks supposedly more accurately known than is possible at the early drilling stage; such a result being potentially dangerous. However, as the amount of data increases the recalculated, semi-variograms approach the underlying semi-variogram of the deposit and the calculations made using them become more reliable and robust.

Jan 1, 1977

Except for uranium search, conventional oil well logging techniques are relatively little-used in mining exploration. The main reasons for this are cost and an apparent lack of awareness of the potential use of the methods in the search for ore. However, relatively inexpensive portable units are currently available for performing the simpler electrical and radiometric logs in diamond drill holes.The emphasis in oil exploration logging programmes is largely on the estimation of porosity. In most mineral work, however, porosity is not very significant, and factors such as mineral conductivity and radioactivity assume an important role.The Bureau of Mineral Resources (BMR) during a programme to explore for uranium and associated base metals in the area east of Rum Jungle, N.T., carried out electrical and radiometric logging of diamond drill holes as a routine part of their investigations. Case histories are described in which the logs were used to aid in defining stratigraphic sequences and transgressive structures in base-metal prospects. Some surface geophysicalanomalies were explained by the logging: induced polarization and electromagnetic anomalies were related to black slate; and self-potential anomalies were related to oxidation of pyrite black slate, or apparent electrokineticeffects in the black slate. The logs provided an objective appraisal of the rock units penetrated and thereby helped to differentiate lithologies.Borehole logging, including newer techniques such as downhole analysis, could be done in geological and geophysical investigations in other areas for a relatively small cost with a considerable potential gain of information.

Jan 1, 1978

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By T S. Giraudo

The Macraes Gold Project, operated by GRD Macraes Limited, engaged GRD Minproc Limited to assist with the evaluation of a pressure oxidation circuit, this being the key component of a recovery enhancement project. The initial study gave sufficient confidence in the process to enter into project execution. GRD Macraes Limited was the first company to license Newmont Mining Corporation's pressure oxidation technology, which aims to improve gold recovery from the carbonaceous sulfidic flotation concentrate. This paper outlines the fundamental chemistry of the process followed by a description of the plant that was ultimately installed. A summary of the commissioning is given together with an overview of the production results to date. The project ramp-up was rapid, with design temperature and throughput being achieved within days of hot commissioning. Gold recoveries have exceeded expectations, improving from around 70% prior to the installation of pressure oxidation to above 84%. The project has increased the nominal gold output at Macraes from 120,000 oz/y to 170,000 oz/y. On-going plant optimisation for process parameters is discussed, giving rise to flexibility in gold production, with key controlling parameters exceeding design.

Jan 1, 2000

By R. H. Colquhoun

"INTRODUCTION The Holt-McDermott Mine is wholly-owned gold mining operation of American Barrick Resources Corp. that begun operations in June 1988.The property is located 0.5 km. south of Highway 101 East in the Harker-Holloway Townships of Northeastern Ontario, 7 miles south of Lake Abitibi and 15 miles west of the Quebec-Ontario border.Employees of the operation travel daily from various communities in the area, predominantly from Kirkland Lake, Ont., which is located 65 km. to the southwest.The significance of the operation is that it is the first full scale operation associated to the Oestor-Porcupine Fault to go into full production in recent history as well as the first Carbon-in-Leach (CIL) operation in the province owing to the natural occurring carbonaceous ores that are associated to the ore body and the geological fault systems.GEOLOGYThe Holt-McDermott deposit is located in the Abitibi Greenstone Belt, a short distance west of the Ontario-Quebec border. Ore grade material follows the footwall contact of a fault zone known locally as the McKenna Fault, which is thought to be a splay off of the Oestor-Porcupine Fault, itself a major feature in the Abitibi belt.The McKenna Fault strikes approximately east-west (as does the Oestor-Porcupine) and dips to the south at sixty-five to seventy degrees. The fault lies within a package of mafic volcanic rocks (basalts). These rocks have been strongly altered and mineralized adjacent to the McKenna Fault, and the resulting lens-like ore bodies constitute the mining targets."

Jan 1, 1989

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By Kyle Selga, Christopher J. Greet

"The Pulp Chemistry Monitor (PCM) has been installed and operated in a number of concentrators in Australasia, and has produced some very interesting results. PCM measures the pH, Eh, dissolved oxygen, temperature and oxygen demand of process streams within a concentrator continuously and in real time.In the example presented in the paper the cleaner feed pulp chemistry is measured, and related back to changes in the mineralogy as well as variations in metallurgical response. For example, a decrease in Eh and dissolved oxygen as well as an increase in the oxygen demand. These changes in the pulp chemistry appear to coincide with increases in the feed grades, probably higher pyrite grades. Further, these variations in pulp chemistry and feed mineralogy have a negative impact on the concentrate grade and recovery.The implication is that if the pulp chemistry is monitored it is possible to predict changes in the mineralogy of the system, and from this the metallurgical response. Further, the changes in pulp chemistry can be used in a control system to counter the changes in mineralogy and maintain the metallurgy.IntroductionIt has long been recognized at a fundamental level that the flotation behaviour of sulphide minerals is dependent on the pH and Eh of the system (for example: Tolun and Kitchener, 1964; Woods, 1976). However, measuring pulp chemical parameters within an operating concentrator has had limited attention. Woodcock and Jones (1970a and b) were among the first to actually collect data from operating plants. Jones and Woodcock (1984) identified some of the chemical complexities of flotation pulps, and noted that most concentrators already operate at high levels of metallurgical performance but there was still considerable scope for improvement. These gains would, in part come from more effective chemical control. In the same volume, Healy (1984) discussed metal ion hydrolysis and precipitation, redox chemistry and how the surface chemistry of sulphide minerals can be influence flotation behaviour. The impact of grinding environment on the pulp chemistry and flotation response of a complex polymetallic sulphide ore is discussed by Forssberg and Subrahmanyam (1993). Their work essentially contrasts the pulp chemical and flotation performance of pulps ground with conventional ferrous grinding media to a fully autogenous system. The data suggested that the reduction or removal of iron hydrolysis contamination from the system could have a positive influence on flotation behaviour, and perhaps the first stage of “controlling” the chemistry of the system should be in the grinding circuit. Grano et al (1995) demonstrated that the collection of pulp, solution and surface chemical data could identify weaknesses within a concentrator, and from these data develop, test and implement solutions that improved the process. Greet et al (2006) showed that the pulp chemical trends observed through primary grinding and rougher flotation circuits of most sulphide flotation concentrators are approximately the same. There are differences in the magnitude of various pulp chemical parameters (pH, Eh, dissolved oxygen, temperature and oxygen demand) as a result of variations in the feed mineralogy and processes employed. Further, it was noted the Eh shifted to more reducing values of the ten days measurements were collected, and this change could be traced to an increase in the iron sulphide content of the feed. Metallurgically, this resulted in an increase in nickel recovery through the recovery of nickeliferous iron sulphides, and a decrease in nickel concentrate grade."

Jan 1, 2016

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

By Adrián Del Carpio

Desde 1995 la planta de Lixiviación de Toquepala desarrolló un sistema de control automático para los procesos de extracción por solventes y electrodepositación. Sin embargo, con el desarrollo de la tecnología y las nuevas versiones de control, dicha plataforma se tornó arcaica. En ese sentido, el presente texto señala la modernización de los sistemas relacionados con el control y supervisión de las áreas de extracción por solventes, depositación electrolítica y áreas auxiliares. Como consecuencia de ello, se incrementó la operatividad, disponibilidad y fiabilidad con cero paradas por perturbaciones eléctricas, así como redujo el tiempo utilizado para el diagnóstico y solución de problemas.

Sep 12, 2011