Search Documents

By R. B. Adair, J. S. Browning

The laboratory batch and continuous flotation pilot plant tests demonstrated the technical feasibility of recovering high grade mica concentrates from weathered mica pegmatite ores of Alabama and Georgia. The research indicated that combinations of anionic and cationic collectors may be used effectively for flotation of fine size mica from weathered pegmatite ores. In continuous tests, concentrates containing 98.5% mica were obtained from the Georgia pegmatite ore; the Alabama pegmatite ore concentrates contained 98.4% mica. The recoveries were 91 and 89% respectively. INTRODUCTION The principal uses of fine ground mica are as a filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 99% of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for several years, the 1963 production of scrap and flake mica totaling 117,251 tons.1 Ground mica is obtained primarily by crushing and milling pegmatites and schists. To a lesser extent, mica is produced as a byproduct of kaolin washing and feldspar and spodumene flotation operations. The processes used in recovering mica by crushing and milling pegmatites are generally simple, consisting of various combinations of alternate roll crushers and trommel screens that separate the mica and gangue at screen sizes coarser than 6-mesh. As these processes are designed to recover only coarse mica, high losses in the plant rejects are common. Large tonnages of tailings from the crushing and screening plants have been accumulated in a number of areas. Methods for treating such products were developed by the Bureau of Mines in 1941,2 but have not been generally applied. More recently, mica flotation research has been completed and published by the Bureau of Mines.3 These methods required complete removal of 150- to 200-mesh materials from the flotation feed with consequent fine mica losses. Later, the Bureau of. Mines investigated methods for-recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials, but not so drastically as to remove the fine sands. This report summarizes the results of these studies. The process developed was effective on pegmatite ores from two locations and should be applicable to the commercial treatment of other mica-bearing pegmatite ores and fine rejects that have been accumulated at various mica-milling operations. DESCRIPTION OF ORES The ores used in the investigation were obtained from the Dixie Mines, Inc., Heflin, Alabama, and the Ruberoid Corporation, Hartwell, Georgia. The sample from Alabama contained muscovite and quartz, with a high percentage of clay, and minor amounts of biotite, kaolin, limonite and tourmaline. The mica in the ore was essentially all minus 4-mesh in size and was free of attached mineral grains. The Georgia sample contained muscovite and quartz, with minor amounts of biotite, kaolin, and limonite. The mica in the ore, which was essentially all minus 4-mesh, was liberated. Petrographic analyses of the two samples are given in Table I. THE ANIONIC-CATIONIC MICA FLOTATION METHOD Previous investigators2,3 have reported that complete desliming of mica ores at 150- to 200-mesh was required prior to flotation with cationic collectors to obtain satisfactory selective separation of the mica from the other mineral components. Numerous tests were made at the Tuscaloosa Metallurgy Research Center to determine if some reagent combination could be used to selectively float finer size mica without complete desliming. The investigation led to development of a process using a simple reagent com-

Jan 1, 1967

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C', D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C', 70 ft.; C' to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.'. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.' The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971

By Carl S. Westerberg

Coal preparation practice and trends follow, among other factors, production trends in any given area. Considering an area the size of a state, some broad predictions may be made after a review of the annual production records. As this paper is concerned with coal cleaning in Utah, data on its production record are pertinent. Table 1 shows the percentage relation of coal production in Utah to the national total as a single figure up to 1935 which includes all recorded production. From 1935 through 1947 these data are presented by years. It is evident from these data that the production of Utah coal is ascending. The reason for this trend is industrial growth in the West resulting in a population shift which accounts for more people than the normal increase would supply together with Utah's relatively fortunate geographical location and its abundance of good-quality coal. Utah is also hopeful of supplying more coal in the future for West Coast power generation.I Utah is not unique among coal-producing states in anticipating greater production in the future. Coal Age states, " . . . it is now evident that a billion-ton yearly production of anthracite and bituminous by 1960 is not impossible." At present it is about 610,000,000 tons, the all-time high in 1947 was approximately 687,803,000 tons. In view of the trend outlined above, obviously more new mines will be required to produce the necessary tonnage. These in turn will require more mechanical cleaning capacity. Whether the required new plants will be built by present operators of mines and mechanical cleaning plants or by others now in the business of producing coal or expecting to enter it is of no consequence in this discussion. The fact is— they will be built.

Jan 1, 1950

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification' determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included. TODAY, as never before, the coal producers of this country are faced with the necessity for obtaining maximum yield of marketable coal of all sizes down to and including the finest. Particular interest is being displayed in a more effective means of recovering the finer sizes which in the past so often have been discarded to waste or treated by inadequate equipment. The reasons for this interest are easily understood. Rising mining costs have resulted in the increased use of mechanized equipment underground for full seam mining. This, in turn, means more refuse in the run-of-mine and also more fines in the feed going to the cleaning plant. Stringent antistream pollution laws now make it necessary at least to impound the fines, and usually it is a paying proposition to recover the coal from these fines before sending them to the storage area. Finally, the market and price of the finer sizes has increased, but at the same time specifications have tightened and the demand is for higher grade products. During the past four years a great deal of publicity has been given to this new process and apparatus for treating fine sizes of ores as well as coal. Excellent discussions of the apparatus itself and the theoretical aspects of the basic operating principles involved in its operation have been presented by M. G. Driessen,1-3 M. R. Geer and H. F. Yancey,4,5 J. W. Hyer6 and more recently by D. A. Dahlstrom8 as well as others.7,9-11 In view of this, it has been decided to include in the present paper only a brief description of the cyclone separator and its operating principles. This paper deals primarily with some of the more practical commercial aspects of the process and equipment required for its operation; the variables in the operation of the cyclone, their effect and means for control; and the results obtained with a 6-in. semicommercial size separator on a variety of fine coals, bituminous and anthracite, using finely ground magnetite for the separating medium solids. A description is included of the commercial-size cyclone separator pilot plant installed by the Dutch State Mines at its Emma mine in Holland, where finely ground slate is utilized as medium solids. Field of Application: The Dutch State Mines cyclone separator operates most efficiently on ores and coal in the size range of % in. to about 48 mesh. On some types of feed, effective separation can be made on sizes as small as 100 mesh, but up to the present, this may be considered exceptional. Depending upon the type of medium used, the specific gravities of separation can be varied within wide limits, up to as high as 2.70, if magnetite is used as medium. Early Development: The development of the Dutch State Mines cyclone as a separator, or cleaner, was the outgrowth of early experimental work by Dries-sen' and others in Holland, just prior to World War 11, in the course of which was discovered the effectiveness of the cyclone in reclaiming and thickening the dense medium used in the "Loess" process of

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By S. A. Falconer

D. A. Dahlstrom—Mr. Falconer has done an admirable job of proving the adaptability of the cyclone to the beneficiation of a very difficult size range in the preparation of coal. The addition of the cyclone to other coarser size methods makes it economically feasible for the coal operator to rigorously control his marketed products at a high and uniform quality level down to the 48 and 100-mesh size. Furthermore, it should be pointed out that by utilizing the cyclone as a deslimer or classifier the —3 200-mesh fraction, usually containing large percentages of undesirable material, can also be quickly and cheaply removed from the clean coal. Advantages of such a step are several: (1) Reduction of ash content, especially where clays and slimes are serious. (2) lower moisture content of the final coal. (3) easier mechanical and thermal de-watering of the fine coal due to higher cake and bed permeabilities. The author has indicated that adjustable control means should be installed on the cyclone operating on a heavy-media slurry. This also holds true for the cyclone acting as classifier, deslimer or preliminary dewatering agent and is worthy of special emphasis. Such controls, while not necessarily automatic, must be simple, rapidly adjustable, and require a minimum of attention. Three methods available to the operator are (1) throttling valve on the feed line, (2) back pressure valve on the overflow, and (3) adjustable diameter underflow nozzles. The first two, while fulfilling the specifications, suffer the disadvantage of restricting capacity if severe throttling is necessary. The third method has little effect on capacity and easily maintains an underflow of correct moisture content. Several designs are possible, but two find the widest application. The first was developed by Robert Piros of The Truax-Traer Coal Co. and uses a simple casting containing two holders for underflow nozzles which can be rotated about an axis parallel to the cyclone centerline. These holders retain the underflow nozzle flush with the conical section walls. When a change in nozzle diameter is required, the new size is placed in the spare holder and rotated into place. A second design utilizes a soft rubber cylindrical tube which is compressed or released from three sides, causing the inner diameter of the tube to decrease or increase. This is achieved by using a machine-threaded,

Jan 1, 1951

By J. L. Schroder, William J. Halvorsen, Wiliam W. Lyons, Kent C. Ware, Sheridan A. Glen, Donald C. Simpsom

The prospects for near-term growth in coal demand are exceptional: the federal government recently targeted 141 oil- and gas-fired generating units for mandatory conversion to coal; coal-to-synfuel developments are proceeding at a steady clip, with construction of a $1.2 billion gasification plant to begin this year in Beulah, ND; uncertainty over nuclear power and stratospheric oil prices enhance the steam coal market; the export market is ripening; and an influential new political force (the Senate Coal Caucus and Congressional Coal Group) is flexing its muscles on Capitol Hill. But the rosy picture is muddled by signals, often conflicting, sent out by federal agencies. Although EPA can be credited with relaxing its grip on the Clean Air Act, its sulfur dioxide control strategy is still often at odds with the Administration's call for domestic energy (coal) development. B. R. Brown, president of Consolidation Coal Co., sums up the situation: "Every mule is pulling in a different direction." Often in the midst of the fray is the small operator who has been hardest hit by the stagnation of coal markets. Layoffs, shortened work weeks, and mine closures were rampant in the eastern and midwestern coal fields, even among large producers. The longstanding boom in western coal was tempered during 1979 by a noticeable slowdown in announcements of new mine construction. The prognosis: Eastern coal will remain in the doldrums for quite a while to come as it works off some 90 Mt of overcapacity. Midwestern coal will fare no better due to the regulatory-influenced appetite of midwestern utilities for low-sulfur western coal. This displacement should ease, though, as new power plants equipped to burn high-sulfur coal come on line in the years ahead. In the West, the National Coal Association projects production to increase a healthy- 10% this year, although mine-to-market transportation looms as the single largest stumbling block to marketing efforts. Fatalities Up 40% in 1979 The National Coal Association estimated total coal production in 1979 at 671 Mt, an increase of 13% over 1978. Of this total, the East and Mid-west accounted for 476 Mt (71%) and the West produced 195 Mt (29%). With the consistent rise in western production playing against flat outputs in the East and Midwest, underground mining's share of total production continues to slip and is expected to account for only 38-39% in 1980. Incidence of deaths and injuries at US coal mines soared in 1979 over 1978 rates. MSHA figures (still subject to final adjustments) reveal a death rate of 0.07 per 200 000 man-hours, up 40% over 1978's 0.05 figure. MSHA chief Bob Lagather attributed the death incidence to the large number of new coal mines put on line in 1978, which he estimated at between 350 and 400. Nonfatal injuries rose to 8.48 per 200 000 man-hours, up about 15% from a 1978 rate of 7.35. In absolute numbers, MSHA counted 144 fatalities and 18 111 lost-day injuries during the 1979 calendar year. The 144 coal mining deaths in 1979 is the highest number of coal fatalities at US mines since 1975.

Jan 5, 1980

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation's water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants. IT must always be remembered, with regard to the problem of water-borne industrial wastes, that stream pollution from any cause is just one factor in the comprehensive problem of water supply in modern times. Industries nonexistent 25 years ago are now flourishing, and supplies of water piped to homes and apartments, as well as the greater number of plumbing fixtures per dwelling and per building, have created an ever growing demand on the country's water resources. Indication of this rapid growth in demand is shown in Table I, which is quoted from Abrams. of Texas increased 287% and the water consumption 7000 per cent." The domestic load varies greatly, depending on the extent of the available supply and the habits of the community. According to the report of the President's Water Resources Policy Commission' the United States Public Health Service reported a national average of 127 gal per capita per day, varying from 60 gal in communities of 500 persons to 140 or 150 gal in cities of 10,000 or over. Other critical areas may be cited to illustrate the inter-relation between new industrial processes and the demands for water in the area where the new enterprise is located. Powell and Wilson have pointed out that during World War 11, in the vicinity of Louisville, Ky., a rapid expansion of industry took place, consisting of numerous synthetic rubber plants. The demand for water increased from 37 million gal per day in 1937 to 62 million gal in 1943. These heavy requirements drew down the supply stored in the water-bearing aquifers to such an extent that urgent plans for recharging were considered. Similar situations have developed in the Los Angeles area and in the vicinity of Texas City. Warne4 has drawn attention to the situation in Los Angeles area, where in the West Basin the withdrawal of ground water in 1945 was 90,000 acre-ft, almost double the amount of the natural fresh water recharge. The draw down has been so severe that the level of the ground water is now below sea level, and sea water is invading the West Basin aquifers at rates up to 300 ft per year. In the Report of the Engineers Joint Council it is pointed out that in the area of Texas City the ground water table has been critically lowered. In 1930 the daily withdrawal from the water-bearing aquifer was 0.5 million gal. By 1945 the quantity withdrawn

Jan 1, 1954

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By S. Mukai, Y. Shah, T. Zshikawa, T. Wakamtsu

In order to recover coal concentrate of low ash and low iron content, the electrostatic separation of coal was studied. It is more successful in the corona discharge field to recover the coal concentrate of low ash and low iron content than in the field without corona discharge. The effect of humidity on the electrostatic separation of coal was then studied. From the experimental results, it was clear that the electrostatic separation was excellent in about 60% relative humidity of atmosphere. Thus, the separation of vitrite from coal is practicable by electrostatic separation. In recent years the demand for high quality coal containing low ash, low iron, and low sulfur has increased. To fulfill this requirement, a higher grade coal concentrate must be produced. Study on the electrostatic separation of coal has been performed for several years in the author's laboratory. From the results of this research, it was considered that the behavior of coal particles in the electrostatic field relates closely to the ash and iron content in coal. In the present paper, the electrostatic separation of coal in corona discharge field was studied in order to recover the high quality coal concentrate and then the effect of humidity on the electrostatic separation was investigated. PREPARATION OF COAL SAMPLES The coals from the Akabira mine, the Kushiro mine, the Miike mine, and the Oshima mine which are famous coal mines in Japan were used in this study. The ash contents of these coals are shown in Table I. From the results of the analysis of the coal samples by the Norelco X-ray diffractometer, it is recognized that the Miike coal includes mainly pyrite, quartz, kaoline, calcite, and epidote; the Kushiro coal: kaoline, quartz, and montmorillonite, and the Oshima coal: siderite, dolomite, and other substances. For the preparation of samples, the coarse pieces of coal were crushed to about 2 mm in diam and then ground in an agator mortar. The ground products were sieved and fractions of 10 — 14 mesh, 14 — 20 mesh, 20-28 mesh, and 28-35 mesh were prepared, respectively. APPARATUS OF ELECTROSTATIC SEPARATION The principal part of the apparatus of the electrostatic separation used in the experiments is shown in Fig. 1. In order to generate the corona discharge field, a needle-shaped electrode combined with a pole electrode is installed as the high tension electrode. In the case of investigating the effects of the humidity on the electrostatic separation of coal, the needle-shaped electrode was combined with a plate electrode instead of the pole electrode as shown in Fig. 2. The pole or the plate electrode was installed to promote the repelling of the charged particles by producing the electrostatic field between this electrode and the grounded roller. It seems to be very useful on the coal separation to install these combined high tension electrodes. SEPARATION OF COAL PARTICLES IN CORONA DISCHARGE FIELD The separation testings on the coal samples in the corona discharge field were performed by the apparatus as shown in Fig. 1. These experiments were carried out under the following conditions: feed size 20 — 28 mesh, room temperature, normal humidity and applied voltage 15-20 KV, and the combined electrodes including the needle-shaped electrode were negatively charged. The results of these testings are

Jan 1, 1968

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971