Search Documents

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By W. H. Wilson, G. Bjarnholt, D. C. Holloway

This paper describes the results of field tests conducted on a 5x25m bench face to evaluate several new concepts for improving smooth wall blasting. These ideas involved the use of notched boreholes to direct the fractures and unconventional types and placements of explosives. The notches were made with a mechanical broaching tool, a water jet and with shaped charges. Borehole pressures were measured with an inexpensive and expendable pressure transducer developed for this program. The testing showed that at hole spacings 38% greater than normal practice, notched holes with half the normal loading density produced equivalent results.

Jan 1, 1986

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By A. Pezzuto

"Pipes are used on mine sites in a variety of applications including transport of slurry, conveying clean and processing water, and in mine dewatering. Mine waters and slurries can cause pipe wear and failures via several mechanisms (or combinations thereof) such as abrasion, scaling, and corrosion. Polyethylene (PE) pipe materials have grown in popularity over the past several decades due to their chemical and mechanical properties (e.g., inertness, flexibility, relatively low density) and low cost. While PE is generally resistant to corrosion, it is subject to abrasion. To combat this, a novel, rubber-like liner is in development. In addition to comprehensive abrasion testing, however, the liner must be evaluated to see how it performs under other conditions. Here, a brief field study is described that tested PE pipes with the new liner against traditional PE pipes to specifically assess mineral scale buildup. The study was conducted in the Reiche Zeche study mine in Freiberg, Germany in six different locations with varying water qualities and flow conditions. INTRODUCTION Water and slurry conveyance are major operations on and around mine and mill sites, from mine dewatering, to tailings transport, to water treatment processes. Conveyance systems in such applications can include great lengths of pipe materials along with pumps and monitoring instruments, and thus represent significant capital investments. Due to the variability of the physical and chemical properties of water and slurries, pipe materials are subject to a wide range of conditions. These can cause pipe wear and eventually failure leading to serious economic, environmental and social, consequences. While pressure-induced pipe failures (e.g., ruptures or ""bursts”) can be immediate, most failure mechanisms involve gradual processes. Scaling and sedimentation can present major problems for pipe systems conveying highly mineralized waters. Sedimentation generally refers to the deposition of suspended solids, such as sand, clay, silt, or organic matter onto pipe surfaces. This phenomenon can occur due to a decrease in water velocity or particle collisions with the pipe wall. Scaling, on the other hand, commonly refers to the deposition of precipitated mineral salts (including oxides and hydroxides) onto pipe surfaces. Mine waters often have extremely high ion concentrations (i.e., high dissolved solids content) due to their interaction with enormous surface areas of minerals, which are exposed during mining and processing operations (Brown and Barley, 2002). As these waters are transported, slight changes in temperature, pressure or chemistry (e.g., pH or ORP) can cause instability with respect to ion solubility such that salt precipitation begins to occur. “Seed” crystals can rapidly grow and attach to pipes, either due to local surface phenomenon near the pipe wall (e.g., which can promote coagulation) or sedimentation of the precipitated solid. Whether due to suspended or precipitated solids, as the solids begin to stick to pipe walls, “aging” or hardening processes can commence; and the build-up of scale can become self-perpetuating as the scale itself provides an attractive “nucleus” for further attachment of particles or crystal growth (Muryanto et al., 2014). Over time, scale-buildup reduces the effective pipe diameter, which can ultimately result in decreased flow velocity, clogging and, in some instances, bursting (Dirany et al., 2016)."

Jan 1, 2017

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By B Reid

"Since the commencement of mining operations at the Cowal Gold Operations (CGO) in 2005, reverse circulation (RC) drilling has been the preferred method for grade control (GC) sample collection. This method was selected because it allowed:for multibench drilling (20 m hole depths for two benches of mining) to aid mine planning increased data density for comparison against the wide spaced ore reserve model angled drill holes to intersect perpendicular to the strike and dip of the shallow dipping mineralisation ability to take two metre sample intervals to enhance the understanding of the mineralisation’s short-scale variability and provide the ability to flitch mine.From June 2008 to December 2013, RC GC was performed using a UDR rotary cone splitter. The field duplicate data over the period displayed strong precision, with a correlation coefficient of 0.94 and an average relative per cent difference (RPD) of 21 per cent for gold. Up to 66.1 per cent of field duplicate data greater than 0.1 g/t fell within ±20 per cent RPD. This is within limits of industry best practice. The Mine to Mill reconciliations over the same period showed the estimated GC grade was 7.7 per cent lower than the calculated head grade (CHG).In December 2013, the Progradex sampling system (PGX) was introduced at CGO due to its advertised ability to capture 100 per cent of the drill cuttings for the complete sample interval, inclusive of fines. Analysis of field duplicate data indicates that since the introduction of the PGX, the sample precision has drifted. From January 2014 to February 2016, the correlation coefficient was 0.92 and up to 51.2 per cent of field duplicate data, greater than 0.1 g/t fell within the ±20 per cent RPD. Over the same 26 month period, the Mine to Mill reconciliation improved to one per cent lower than the CHG. Granulometric analysis of the RC samples collected from the PGX indicated the fines material(<212 µm) averaged up to 22 per cent of the samples mass and following assay determination, the fines material represented a weighted average of 31 per cent of the total gold content within the sample.This paper highlights the:importance of the complete capture of all drill cuttings during an RC drill programinfluence of fines material on the sample quality and accuracyimpact sampling of the fines material has on the Mine to Mill reconciliation performancechallenges experienced in commissioning a PGX system.Citation:Reid, B, 2016. A Fine Looking Sample - the Importance of Fines in Grade Control Sampling to Mine to Mill Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 28–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By R. Ratnagiri, B. Minaie

"In order to expeditiously produce defect-free metallic components in materials processing applications, the relationship between the process parameters and the product properties needs to be well understood while minimizing the production engineering iterations. To achieve this goal, a realistic mathematical formulation of the process should be carried out and an appropriate numerical modeling of various phenomena occurring in such process should be implemented. The materials processing of transforming the molten material into a finished metallic component involves fluid flow and solidification/melting. In the present paper, a finite element based analysis of the fluid flow ·and solidification/melting phenomena in cavities is presented and the various issues in modeling these phenomena are discussed. These transport phenomena play an important role in determining the final characteristics and material properties of the part by affecting the formation of defects and microstructure. A realistic numerical modeling of these phenomena can significantly reduce the rejection rates during the process and can increase the quality of the final product.IntroductionDuring the intelligent materials processing of various metallic components, it is often required to have a thorough knowledge of the behavior of the transport phenomena involved in this process. This is due in large to the coupling that exists between the transport phenomena and the final material properties of the components produced during materials processing. This interrelationship demands that the pertinent transport phenomena in the form of fluid flow and solidification/melting be studied and predicted accurately. In many materials processing applications, the fluid flow is in the form of either a forced convection free surface flow intended to fill a cavity or a natural convection flow resulting from the gravity when the cavity is filled. In either case, the phase change in the form of solidification/melting is also involved in order to complete the process. However, the thermal history during this phase change has a direct impact on the material properties of the final part and the possible defect formation that may be involved. This thermal history itself is dependent on the nature of the fluid flow during the earlier stages of the process. As such, there is a coupling between the fluid flow, phase change, microstructure, and defect formation in the resulting component. It is therefore necessary to analyze these phenomena in order to find optimum methods to produce good quality parts by minimizing the defects that may be generated. Such an analysis can result in the development of appropriate numerical models for the process that can facilitate the economical and timely manufacturing of various components with high consistency. The present paper discusses the issues related to the transport phenomena encountered during materials processing of components engineered largely by using various combination of convective fluid flow and solidification/melting in cavities."

Jan 1, 1994

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By V. K. Risinggård, M. Sparta

We report on the development of a finite-element method model for a pilot furnace for the production of manganese alloys. The model is a multiphysics model that addresses material flow, electrical conditions, heat transfer, and physical and chemical transformations. It is capable of studying both quasi-steady and transient states in time-dependent simulations. The model includes common charge materials and fluxes and can simulate production of both ferromanganese and silicomanganese alloys with acid and basic slags, as well as changing charge compositions. The model output provides access to the material distribution in the furnace during furnace runs, temperature profiles, current paths, energy balances, and alloy and slag production rates and compositions.

Apr 16, 2024

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008