Search Documents

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992

By Sang Han Son

The vapor pressures of FeCL2 and ZnCL2 in the FeCL2?ZnCL2 system were measured by the transpiration method at 873K and 9I7K, The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCL2?ZnCL2 melts, It is presumed that the complex molecule FeZnCl4 as well as FeCL2 and ZnCL2 exists in the vapors in equilibrium with molten FeCL2-ZnCL2 mixtures, The activities in the FeCL2-ZnCL2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCL14 in molten FeCI2?ZnCL2 mixtures.

Jan 1, 2003

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Kandipati Sreenivasarao

Ion and precipitate flotation involve adding an appropriate collector to aqueous solutions containing metal ions, to form hydrophobic metal-collector complexes or precipitates that can be removed by flotation. With a better fundamental understanding of the effects of physical, engineering and chemical parameters on the performance, ion and precipitate flotation techniques could usefully complement techniques now available for removing metal ions from dilute solutions. The removal of Cu(II), Pb(II), Cd(II), Cr(III) and Cr(V1) has been studied, using different types of collector, according to the nature of the metal-bearing species. The effects of collector/metal ion ratio, and solution and froth height on the flotation kinetics, bubble coverage by the metal-collector complex, recovery of metal and effluent quality are reported. The observed behavior is related to the solubility products of the metal-collector complexes, which were also determined.

Jan 1, 1994

By Regina Krachler, Herbert Ipser

"The principles of the derivation of statistical-thermodynamic models to interpret the compositional variation of thermodynamic properties in non-stoichiometric intermetallic compounds are discussed. Two types of models are distinguished: the Bragg-Williams type, where the total energy of the crystal is taken as the sum of the interaction energies of all nearest-neighbor pairs of atoms, and the Wagner-Schottky type, where the internal energy, the volume, and the vibrational entropy of the crystal are assumed to be linear functions of the numbers of atoms or vacancies on the different sublattices.A Wagner-Schottky type model is used for the description of two examples with different crystal structures:For B'-FeAl (with B2-structure) defect concentrations and their variation with composition are derived from the results of measurements of the aluminum vapor pressure; the resulting values are compared with results of other independent experimental methods.For Rh3~ (with an NiAs-derivative structure) the defect mechanism responsible for nonstoichiometry is worked out by application of a theoretical model to the results of tellurium vapor pressure measurements. In addition it is shown that the shape of the activity curve indicates a certain sequence of superstructures.In principle, there are no limitations to the application of statistical thermodynamics to experimental thermodynamic data as long as these are available with sufficient accuracy, and as long as it is ensured that the distribution of the point defects is truly random, i.e. that there are no aggregates of defects."

Jan 1, 1996

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique. thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg-robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By Henry L. Ehrlich

This survey compares bioleaching and biobeneficiation by autotrophic bacteria with that by heterotrophic bacteria and fungi Some physiological principles are reviewed. Advantages and disadvantages of autotrophic and heterotrophic leaching are discussed. Principles of anaerobic leaching by autotrophs and heterotrophs are introduced. and the advantages? over aerobic heterotrophic leaching are discussed. Examples of useful organisms in the autotrophic and heterotrophic categories are cited.

Jan 1, 1991

By Kenneth McGowan

"The aluminum industry is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating accounts for 25% of the energy consumed to manufacture aluminum. Consequently, the generation of this energy results in the production of a significant amount of CO2 (over 3.75 million metric tons in 2003)1. As a result, the Aluminum Industry Technology Roadmap of 2003 listed the development of improved refractory materials as a goal to reduce energy use and decrease greenhouse gas creation. The result of a R&D effort addressing this desire is the development of patented microporous refractory materials for metal contact applications in all furnace areas including the belly band. It has been demonstrated that this material can reduce energy consumption up to 38% in furnaces and significantly reduce heat loss in launder and trough systems. Furthermore the material developed is non-wetting and remains un-penetrated by metal throughout its lifetime. The material does not contribute to the formation of corundum. As a result, the energy efficiency of an older lining remains intact compared to standard refractory materials which may have an initial high insulating value (such as lightweights and board) or standard dense refractory (even with penetration inhibitors) both of which show a rapid increase in thermal conductivity as the refractory is penetrated with aluminum and formed corundumIntroductionThe aluminum industry is the second largest producer of metal in the United States, behind the iron and steel industry. It is the 5th largest consumer of energy and the largest consumer of energy on a per-weight basis. Process heating is required to melt, hold, purify, alloy, and heat treat the metal and accounts for 25% of the energy consumed to manufacture aluminum. As such, process heating is the second largest energy consuming operation. Smelting, which utilizes an electrolytic reduction process is the largest energy consuming operation1.Most process heating is accomplished through the use of fossil fuels, either directly or indirectly. The choice of fuel is dependent on a plant’s location and fossil fuel availability. Table I shows the processes impacted by refractories and the calculated BTU’s generated by usage of the respective fuels as well as the Metric Tons (MT) of metal passed through each process in 20001."

Jan 1, 2009

By Cheng Gong-jin, Chu Man-sheng, Liu Zheng-gen, Zhang Yong, Liu Jian-xing, Xue Xiang-xin

"High chromium vanadium-titanium magnetite is one kind of Fe-V-Ti-Cr composite ore resources, which owes high utilization value. Owing to lacking systematic study on the sintering of this ore home and abroad, effects of carbon addition and basicity on sintering process and sinter metallurgical properties, such as sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation were investigated systematically under laboratory conditions in the paper. The results shows that, when high chromium vanadium-titanium magnetite proportion is kept unchanged as 13% in sintering feeds, sintering process index and metallurgical properties are the optimum under carbon addition 5.0% and basicity 2.70, which meets the requirements of blast furnace burdens. This research provides technical parameters for practical sintering production of high chromium vanadium-titanium magnetite.IntroductionHigh chromium vanadium-titanium magnetite (hereinafter abbreviated as hi§h-Cr V-Ti magnetite), in which Fe is closely symbiotic with Ti and isomorphous with V and Cr1'- l, is one kind of typical vanadium-titanium magnetite resources with high comprehensive utilization value but the difficulties are extremely high due to complex chemical composition and mineral structure. At present, the feasible and mainstream utilization process of high-Cr V-Ti magnetite should be the route of agglomeration-blast furnace smelting. Thus, sintering production is the foundation for high-Cr V-Ti magnetite utilization. However, till now there are few research documentations on high-Cr V-Ti magnetite sintering home and abroad. Under the above background, this study focused on detailed researches of high-Cr V-Ti magnetite sintering. Sintering process uses the powders or fine iron ores to produce artificial rich ore with good metallurgical properties 4l Solid fuel provides 90% heat requirement during sintering15J. The appropriate amount of fuel and flux should be added during sintering in order to provide necessary heat and maintain the desired basicity16l. That is to say, carbon addition and basicity are two key factors affecting metallurgical properties of sintering products17J. Therefore, the effects of carbon addition and basicity on sintering process and metallurgical properties, including sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation, are systemically investigated under laboratory conditions in the study, on purpose to achieve the optimization of sintering process for high-Cr V-Ti magnetite."

Jan 1, 2013

By V. E. Antonov

Hydrides of iron and iron-based alloys are thermodynamically stable only at hydrogen pressures in the gigapascal range and rapidly loose hydrogen under ambient conditions. At low temperatures, however, these hydrides can be retained in a metastable state at atmospheric pressure after being cooled under the high pressure to liquid nitrogen temperature. This review will discuss the current state of studies on phase transformations in the Fe-H and related systems and also on the composition, crystal structure and physical properties of the hydrides, both under high hydrogen pressures and in the "quenched" metastable state at ambient pressure. The studies at ambient pressure include magnetization measurements, X-ray and neutron diffraction, Mossbauer spectroscopy and inelastic neutron scattering. In the sections on Mossbauer and structural investigations of hydrides of Fe-Cr and Ni-Fe alloys new experimental results will be presented.

Jan 1, 2002

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical' challenges are evaluated and discussed.

Jan 1, 1998

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Shawn A. Cefalu, Matthew J. M. Krane, Kent J. VanEvery

"Segregation during electroslag remelting (ESR) of a nickel-chromium-molybdenum alloy (Ni-8 wt% Cr-25 wt% Mo) has been modeled. Features of the model include species transport and AC electromagnetic effects coupled with fluid flow, heat transfer, and solidification. The effect of varying ingot diameter and melt rate, on macrosegregation patterns, local solidification time, and liquid pool profiles obtained from this model are demonstrated. The results show that the macrosegregation in the ingots correlates to the filling velocity.IntroductionElectroslag remelting (ESR) is a secondary melting process used to refine the chemical composition and the microstructure of metals. Macrosegregation of solute elements causes defects in ESR ingots, including freckles and the maldistribution of phases. These defects are not correctable through heat treatment due to the large length scales over which they occur. However, the frequency and distribution of these defects may be minimized, or even prevented, through process control based on an understanding of the conditions that lead to their formation.In the past, studies have been conducted on the effect of the process parameters on the shape of the melt pool and the thickness of the mushy zone [1-7]. In these studies, the shape of the liquid pool is determined by consideration of the heat and fluid flow induced by electromagnetic (Lorentz) force and thermal buoyancy. The transport of solute and the resultant solutal buoyancy effects were not considered in these macroscopic models. Defect formation is tied to formation of secondary phases (e.g., freckling and white spots in nickel superalloys) [5,8]. In cases where secondary phase formation is calculated (e.g., [6]), phase fractions are determined using a micro-scale model given the local solidification time (LST) and local thermal history from the macroscale model.Using the local thermal history from the macroscopic transport model to predict microstructure increases the importance of the accuracy of those results. This investigation models the macrosegregation of molybdenum during the ESR of a Ni-Cr-Mo alloy. The effect of macrosegregation on pool shape and depth is demonstrated, along with its effect on the local solidification time. By comparing the relative effects of the melt rate and ingot radius, a better understanding of the factors that affect macrosegregation, and ultimately secondary phase formation may be obtained."

Jan 1, 2004

By Ari JokiIaakso

Three different sulphidic raw materials were treated in a laboratory scale laminar flow fur-nace simulating suspension smelting conditions. The materials were a pure chalcopyrite concentrate, a high-antimony concentrate (tetrahedritic), and crushed copper mattes. The gas preheating temperatures were 500 -1 100°C ana the atmospheres ranged from N2 to N2 -75 % O2, Two particle size fractions were used for the concentrates with x = 20 -38 um and x = 62 -74 um, and three for the granulated copper mattes with x < 37 um, x = 62 -88 um, and x = 125 -177 um. Scanning electron microscopy combined with energy dispersive analysis and backscattered electron analysis was used for determining the morphology and the mineralogy of the reacted particles. Fragmentation of the particles were observed in all materials during the flash oxidation, the conditions depending on the iron and sulphur content and the original particle size fraction of the material. The melting and/or reaction stages of the particles in different conditions were studied from powder samples. Polished sections were examined in order to follow the development of porosity and the mineralogy of the particles.

Jan 1, 1989

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don&apos;t allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir&apos;s law is discussed for different operating conditions.

Jan 1, 1996

By Ben Bowman

For certain ferroalloy furnaces, such as ferrochrome or ferromanganese, there is still doubt about the mechanisms operating under the electrode tips. In this paper a model is built that does not call upon an arc. The medium is best described as an electrically conducting slurry, a mixture of liquids, solids and gas. There are two sources of propulsion, the Lorentz force within the conducting part and buoyancy generated by CO bubbles, creating two opposed poloidal circulation loops, downward below the electrode axis and upward further out.

Jan 1, 2014

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003