Search Documents

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Yavuz Ali Topkaya, Aydin Rusen

"In this study, zinc and lead recovery from zinc plant leach residue obtained from Çinkur using hydrometallurgical methods have been investigated by laboratory scale experiments. Considering more than one million tons leach residue (LR) rich in Zn (12.43%) and Pb (15.51%) in the stockyard and environmentally hazardous, it is essentially necessary to process Çinkur LR. Zinc and lead have been recovered in two main stages. As a first step, Çinkur LR was releached by using hot sulphuric acid for zinc recovery. About 72 % Zn was recovered by using 150 g/l H2SO4 at 95 oC in 2 hours with a pulp density of 200 g/l. Secondly, for lead recovery brine (NaCl) leaching tests were performed on the secondary Çinkur LR obtained after acid leaching process. In brine leaching while lead recoveries up to 95 % could be attained at a low pulp density, the maximum recovery obtained was 84.9 % at a high pulp density (200 g/l) with 300 g/l NaCl concentration in 10 minutes at 95 oC. Introduction Zinc and lead have been known and used by humans since ancient times and also they are important nonferrous metals [1]. Zinc and lead have different properties thus they are used in various application areas, ranging from automobiles to construction, from batteries to textile. Zinc and lead deposits are widely distributed in the Earth’s crust. The principal ore mineral for zinc is zinc sulfide, Sphalerite (ZnS), and lead sulphide, Galena (PbS), is the main source of lead in the world [2].Although zinc is generally produced from sulphidic ores (ZnS) or concentrates by Roast – Leach – Electrowinning (RLE) in the world, in Turkey, zinc production is based on zinc carbonate ores (ZnCO3), and at the Çinkur plant zinc was produced from zinc carbonate from its establishment to 1997 due to high reserves of zinc carbonate in that region. Çinkur is the only plant in Turkey that produces Zn from primary ore containing ZnCO3 by Waelz – Leach - Electrowinning route [3]. However, due to depletion of local high grade ores, oxidized ore concentrates were imported from Iran after 1997, until this plant was shut down. Therefore, there are two different leach residues (LR) which are Turkish LR (TLR) and Iranian LR (ILR) in Çinkur stockpiles. It has been estimated that the total amount of leach residue is more than one million tons of which the major part is Turkish leach residue (TLR)."

Jan 1, 2008

By Ricardo Morales

Reactions between solids and a gas phase have many interesting theoretical aspects as well as technological applications. The present group had carried out experimental investigations as well as theoretical studies of a number of gas-solid reactions over the past decade and was able to derive interesting results. Studies of the decomposition of alkaline earth carbonates were carried out by thermogravimetric analyses. The experiments were carried out using thin powder beds as well as iso-statically pressed compacts with thermocouples embedded in the same. The investigations revealed the complexity of the reactions and the impact of the heat- and mass transfer aspects on the reaction kinetics. In the case of BaCO3, the kinetics of decomposition was complicated by the formation of a liquid phase. In the case of SrCO3, the reaction kinetics could be simulated by theoretical modeling. Gas-solid reactions were also employed as a versatile process tool towards the production of alloys and intermetallics involving transition elements by hydrogen reduction of complex oxides involving transition metals. Thin powder beds were employed to examine the micro-kinetics, while fluidized bed technique was utilized to produce bulk alloys. Preliminary correlations could be drawn between the thermodynamic stabilities of the oxides and the activation energies of chemical reduction steps. Adjusting the process parameters, products at nano-scale could be produced. The structural, mechanical and thermal properties were investigated in the case of these products. The potentialities of this method as a green route to produce industrially important alloys and intermetallics with unique properties are demonstrated.

Jan 1, 2006

By Duck Jae Lee, Kwan Ho Kim, Ji Whan Ahn

"In Korea, reutilization of constructions waste is gaining an increasing attention as generation of construction waste is projected to increase continuously. In current practices, the concrete waste is simply crushed and used as a low application such as paving, back filling, etc. In this study, a new process was developed comprising of heat pretreatment, autogenous milling, and density separation for complete reutilization of concrete waste. Firstly, the concrete waste was crushed using autogenous milling. The coarse size fractions from autogenous milling have a density of 2.5g/cm3 and a water absorption ration 3.0%, which meet the specification of the first class of KS F 2573. The fine size fractions were further separated using a hindered-settling column into two products 1) underflow, 2) overflow. The underflow sample was a high quality fine recycled aggregate which can be used for concrete making, and the overflow sample was an enriched cement material can be also used for CO2 sequestration by mineral carbonation. Introduction Kwan Ho Kim1, Ji Whan Ahn2, Duck Jae Lee1, Hee Chan Cho1 Recently, the importance of resource recycling is gaining a greater attention due to the increasing price of natural resource. Recycling is beneficial for not only the management of waste, but also the reducing of consumption of natural resources and huge energy consumption to treat of natural resource. The construction and demolition waste comprises the major industrial waste generated in Korea. It increased to 54 million tons in 2004, and is projected to increase to over 300 million tons in 2020, as many buildings reach the end of their 30 years life. Among total waste, the proportion of concrete waste was about 30% in Korea. Due to its large volume, recycling of concrete waste is the most important aspect of the waste management. In the current practices, the concrete waste is simply crushed and used as a recycled aggregate. The recycled aggregate has a low quality and most of them are down cycled for usage as paving material, back-filling material, concrete bricks, etc. It cannot be reused for replacement of natural aggregates because cement mortar is not separated perfectly from aggregates. These kinds of recycled aggregates tent to be weaker, more porous and have a higher value of water absorption. When these aggregates are used in concrete making, there are problems of higher total water demand, low compressive strength and durability [1-5]. And recycled fine aggregate is not almost recycled due to its low quality. In this study, a new processing circuit is developed to produce not only highquality recycled coarse aggregates but also fine aggregates and cement material from concrete waste."

Jan 1, 2008

By J. Garvey

The new Cyprus Miami electrolytic copper refinery was commissioned in October 1994. The refinery has been operating at its design capacity of 190,000 short tons per year, and in recent months to 110% of design capacity, producing high-grade electrolytic copper cathodes. Basic and detailed engineering, performed by Fluor Daniel Mining and Minerals, incorporated state-of-the-art technology, including stainless steel cathodes, automated electrode handling, fine-filtering of the commercial electrolyte, autoclave leaching of the anode slimes and other techniques. The major design goals have been safety of operation and quality of the product. Relatively high cathode current densities of 30 amperes per square foot and greater have been applied since start-up. Cathode current efficiencies of over 94% have been achieved since the latter part of 1997. The cathodes were certified on the Comex and LME markets during 1996. ISO- 9002 certification is in progress and should be completed during the first quarter of next year. This report discusses some of the studies that were performed to obtain an optimum layout for efficient materials handling and to create optimum conditions for producing high quality cathodes. A description of the design and operation of the anode slimes facility, including decopperizing with autoclave leaching, is provided. Finally, a description of the start-up experiences and present operation of the electrorefinery are presented.

Jan 1, 1999

By Andrew Shabalin, Vladimir Skorohodov, Svetlana Babaeva, ?lga Makovskaya

"At processing of some kinds of wastes (electronic scrap, secondary materials, spent nuclear fuel) in nitric acid solutions, and also in technology of silver refining, the significant amounts of palladium and platinum passes into a solution. The ion-exchange concentration of palladium and platinum in nitric acid solutions (5-500/dm3) are investigated. More than 30 various classes of ionites are tested. The most chemically resistance resins at the given conditions are identified. It is shown, that the maximum sorptive capacity to studied metals at high acidity the complexing, synthetic and inorganic sorbents possess. To definition of platinum metals sorption optimum conditions the kinetics is studied, isotherms of a sorption at various parameters from nitrate solutions are obtained. The conditions of the platinum and a palladium desorption from the pregnant sorbents and its regeneration with the subsequent reuse of materials were defined. The raw materials containing precious metals have very diverse composition and physical properties. Commonly the materials are processed by hydrometallurgical way. If gold or PGMs there are in raw materials to its opening hydrochloric acid solutions are applied. As an oxidizer nitric acid, hydrogen peroxide, gaseous chlorine, etc are used. Nevertheless, at processing of argentiferous materials and preliminary treatment of a waste including the spent nuclear fuel, nitric acid solutions are often used and the specified metals in some extent pass into solution [1]. Therefore selective extraction of PGMs from nitrate solutions is an actual problem. In the present work the ion-exchange concentrations of palladium and platinum in nitric acid solutions (5-500 g/dm3) are investigated. At the testing more than 30 various classes of ionites the most chemically resistance resins at the given conditions are identified. These resins are synthesized on the base of polyacrylate, styrene-divinylbenzene and vinylpyridine. For a selection of the most effective resin among what are made in Russia and overseas, a number of ionites with various functional groups were studied. Influence of functional groups type on a PGM sorption is shown for extraction of a palladium as an example (table 1). The presented data shows, that palladium concentration in a phase of ionites depends on sorbent type. If the increasing of solution acidity essentially reduces palladium sorption by sulfonic cation-exchange resins (KU-2×8) than its sorption by strongly basic anionites is approximately equal. Intermediate position is occupied by complexing sorbents. The latter (AN-31, SN-3, ANKB-35, Lewatit TP 207, Purolite S 930) are the most effective for extraction of PGMs from nitrate solutions from the point of view of capacity value. According to [2], solution behavior of Pt (II) and Pd (II) are similar. As is known from coordination chemistry, ligand environment of the metal ions substantially impacts to character of electronic spectra. The figure 1 shows the results of measurements of optical density of platinum bearing solutions with various concentration of nitric acid at ?=400 nanometers"

Jan 1, 2008

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By Emilia Visileanu, Eftalea Carpus

"Due to the demographic explosion and development without precedent of the consumer society, the capacity to destroy the ecological balance the entire planet life depends on, acquire new dimensions. In this context new approaches on society development are imposing as well as special responsibilities for stopping and preventing Earth destruction and repairing the damage already done. The zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the.1. INTRODUCTIONThe zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the economy stability.2. ECOLOGICAL CONCEPTSA long-living Romania means:The closing of the production cycles, by waste reusing and recycling; the reducing of the use of fossil fuel; the improving of the material qualities, for extending the economical life of the products made by these materials; the reducing of the transport traffic.In this context, ecology, the star science with the ability to conserving and renewal of the environment is making its way, having the following principles:•,everything is bind by everything – is referring to the importance which the environment has for a great number of allied fields;•,everything leads to somewhere – the principle of the indestructible property of material (in nature, there must not exist wastes);•,nature does it the best – ecology becomes the responsible science with the governing of the strategic laws between man and nature, man takes advantage of the natural resources which he cannot create by himself and nature must feel guarded and not destroyed by this alliance;•,nothing is for free – the polluter pays.The protection of the natural environment means:•, its strong knowledge and that of the interactions between the social economic system and the natural system, the foreseen of the most close and most distant consequences of these interactions;•,the rational usage with maximum economical character of the natural resources not depending on their origin;•,preventing and direct fighting against as well on the degradation of the environment caused by man, as on those produced by natural causes;•,the ability to harmonize immediate interest of the human society on long and permanent term, using the natural factors of the environment."

Jan 1, 2008

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By R. Escalera-Lozano, M. Herrera-Trejo, M. A. Pech-Canul, J. López-Cuevas, A. L. Leal-Cruz, M. I. Pech-Canul

"The use fly-ash (FA) and rice-hull-ash (RHA) offers the potential for the manufacture of hybrid Al/SiCp/spinel composites via reactive infiltration, both with recycled aluminum. The main reason behind this statement is the beneficial role that both waste materials play in preventing the degradation of SiCp reinforcements when the composites are processed with aluminum in molten state. Experimentally, MgAl2O4 is formed in situ during the infiltration of SiCp-preforms in the temperature range 1050-1150 oC for 50-70 min in argon atmosphere at a pressure slightly above to that of the atmospheric pressure. Results reveal that both FA and RHA help in preventing SiCp dissolution and the subsequent formation of the unwanted Al4C3; and although FA-composites still might be susceptible to corrosion via Al4C3 -by the interaction of native carbon in FA with liquid aluminum- a proper FA treatment significantly mitigates its deleterious effect. Primary corrosion mechanisms and strategies to overcome the potential degradation effects are outlined.IntroductionOwing to inherent materials characteristics and post-processing complications –such as corrosion damage- development of metal matrix composites (MMCs) from recycling/waste sources might be a challenging task. Fly-ash (FA) and rice-hull-ash (RHA) are two primary waste materials that offer excellent opportunities for the development of Al matrix composites. Due to its singular hollow-spherical shape and low density, FA has attracted the attention of many researchers. For this reason, most of the efforts to develop Al-based composites from waste materials have been centered on the use of fly ash. Extensive research efforts in the use of FA for Al-based composites have been undertaken by Rohatgi and coworkers [1-4]. In addition to lowering costs, incorporation of fly ash into aluminum has been proved to decrease the materials’ density, increase their hardness, abrasion resistance and stiffness [1]. One of the major outcomes from the mechanical evaluation of aluminum composites prepared with fly ash is that related to their compression characteristics. Typical compressive stress-strain curves form A356/hollow fly ash composites show a linear elastic region followed by a plateau (associated to the collapse of the hollow particles), and then an increase in stress, representing densification of the foam. The crushing of the cenospheres in the composites has been related to an enhancement in the energy absorption capabilities of the material and to a better damage tolerance [4]."

Jan 1, 2008

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Lidong Teng, Seshadri Seetharaman, Aida Abbasalizadeh

0In the present paper, the feasibility of the recovery of dysprosium from spent Nd-Fe- B magnets containing approximately 9 wt% Dy was investigated by using molten salt process. The salt bath consisted of a mixture of NaCl-KCl-LiCl corresponding to the ternary eutectic composition. AlCl3 was used as a chlorinating agent in order to enable an efficient dissolution of metal in the molten salt phase in the salt bath. The metal chloride which is formed as the result of chemical reaction between the metal in magnet and AlCl3, is subsequently subjected to electrolysis in order to be deposited on the cathode. Graphite rods were dipped in the salt bath as electrodes and alumina crucibles were used as the containers for the electrolytic cells.

Jan 1, 2014

By Leonard A. Duval

This concept employs a viable energy saving method that uses a solvent to separate oil from particle matter; it can be used in metal forming industries to deoil sludges, oxides, and particle matter that is presently committed to landfill. If oily particles are used in their oily state, severe consequences to environmental control systems such as explosions or filter blinding, occur in the air handling equipment. This is due to the presence of hydrocarbons in the stack gases resulting from the oily particles. After deoiling, the particles can be recycled and the separated oil can be used as a fuel. The process does not produce a waste of it's own and does not harm air or water. It demonstrates the dual benefits of being commercially viable and in the national interest of conserving resources.

Jan 1, 1994

By G. Cifuentes

It's know that the cathodic purity and the electrolyte treatment is affect for the solid present in the electrolyte. Anodic slimes properties (f.e.: chemical composition, crystalline composition, sedimentation) was studied in copper electrorefining, this properties were modify through by anodic composition and current density. In this paper will be present only the preliminary anodic slimes relationship at different lead anodic composition. The anodic material was doped during the poured process with lead at different composition. It's confirm the apparition of the (Bindheimitte) SMbz07. The specific gravity of this specie is approximately 7.3 - 7.5, with this values is biggest the probability of sedimentation and smaller the slimes not sedimentabel.

Jan 1, 1999

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Hiroshi Maeta, Takao Kino, Hirota Osono, Kikuo Matsusaka, Azusa Shida

"Prior to refine an ultra-high purity material, it is necessary to estimate the surface cleanness of a base material. In this report, the cleaning method of a surface for refining of an ultra-high purity aluminum has been studied. Aluminum sample of 99.999% purity was p9lished mechanically and electrically and washed with various solvents. Surface composition and a depth profile near the surface were examined. Based on the experimental results, surface structure of an ultra-high purity aluminum was discussed.IntroductionRecently, studies on high purity metals have become of interest, and we have reported .various properties of an ultra- high purity aluminum1- 2)In order to purify a metal, it is necessary to clean a work area and to make vacuous as possible. So, we are studying the purification of aluminum by an ultra-high vacuum refining system and a zone refining system set up in a clean room with cleanliness class of 1000.Now, in order to avoid a mixing of impurities into the refining metal, a surface cleanness of a base metal is very important factor. The purity of the base aluminum used our work is 99.999%, but the surface state of the base aluminum is not clear. Aims in this work .are to investigate the surface state and to obtain the cleaning method of the base aluminum.Experimental procedureSamples used in this work were 99.9% (3N), 99.99%(4N) and 99.999% (SN) aluminum produced industrially and 99.9999% (6N) aluminum purified by us."

Jan 1, 2000

By Kenji Monden

A simple technique is presented to evaluate optical property of biomimetic microlens array (BMA) as an antireflective surface on a polydimethylsiloxane (PDMS) sheet. The integration of these structures is done by a thermoforming process. We have only UV-VIS spectrophotometer for optical evaluation apparatus. The transmittance of the sheet is measured with angled sample holder. The 50 deg. transmittance of 270nm pitch BMA on PDMS sheet increases from 87 to 92% after the moth-eye structure is introduced. The transmittance of 350nm pitch BMA on PDMS sheet increases from 87 to 96% after the moth-eye structure is introduced. The transmittance increases with increasing pitch of BMA. The results obtained using UV-VIS spectrophotometer with handmade sample holder.

Jan 1, 2015

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989