Search Documents

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Gennadiy M. Poletayev, Mikhail D. Starostenkov, Alexandra S. Starostenkova

"The process of the combustion synthesis was modeled by computer simulation using the molecular dynamics method. The set of the critical parameters regulating the velocity of the reaction was found from these computer experiments. It was established that the character of structure-energetical transformations at the combustion synthesis in the systems Ni-Al and TiAl depended on the type of boundaries used for the phases delimitation in the bimetal thin films.IntroductionProducing new materials and products, based on the combustion synthesis (CS), is the objective of scientific investigations as one of the most perspective one for industrial applications. But there are several problems connected with theory and experiment. It allows us to forecast the properties of materials. First of all, the main problems are stipulated by structure-energetical transformations taking place at high velocities of the reaction and at high temperatures. It prevents the analyzing of the transformation mechanisms in materials, taking place at microscopic, atomic levels in details.It is evident, that computer simulation allows to decide some problems and to approach to more exact theoretical presentation of structure-energetical reactions taking place at CS. It is known, that the most typical systems, where CS is observed, are bimetals Ni-Al and Ti-Al. The investigation of interphase boundary stability in the systems of Ni-Al and Ni-Fe was made by the method of molecular dynamics in [1]. The bimetal thin film was presented by the packing of atoms in the plane (111) of FCC lattice. It was found that the discrepancy in the sizes of atoms A and B of bimetal was compensated by the formation of 60° top dislocations, set against interphase boundary in the absence of point defects and free volume. The density of top dislocations was proportional to the factor of size discrepancy of atomic components of the bimetal. Diffusional reconstruction of the interphase boundary and areas, situated near it, was observed only at definite concentration of point defects - vacancies, inculcated in the structure of the bimetal at the definite temperature. The atoms of the bimetal component of less size penetrated in the area of the second component with higher velocity. The clusters of intermetallic germs began to form. It led to the growth of the system temperature and acceleration of the process of the diffusional reconstruction of thin film. The following transformations were found: top dislocations splitted into single ones, which climbed from interphase boundary into the zone of more plastic component; the formation of sub grain structures took place."

Jan 1, 2001

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Shoji Taniguchi, Lifeng Zhang

"In this paper, firstly the 3D single-phase turbulent steady fluid flow in a vessel with four baffles stirred by a single impeller is mathematically simulated. Turbulence is modeled by using the standard k - e model. Sliding-grid method is used to model the impeller. The flow domain is divided into two cylindrical, the inner one rotates at the same speed as the impeller, and the outer one is fixed with the baffles. Results indicate that the high-speed zone is near the paddles, and larger stirring speed generates larger fluid flow velocity. The calculated stirring intensity data are used to analyze the experimental results. Secondly the effects, such as filter pore size, gas flow rate and NaCl concentration, on bubble size are studied by experiment. For the particle removal rate by bubble flotation in this vessel, first order kinetics is adopted. The effects of initial number of the particles, gas flow rate, particle and bubble size, stirring speed and surface condition, on the removal rate constant are discussed, and an empirical equation is derived by experimental data. At last, a simple model is developed to study the particle attachment probability on bubble surface under turbulent flow conditions. IntroductionIt is well known that inclusions have a bad effect on steel quality. Trying to remove inclusions from liquid steel as many as possible is one of the main objects for the metallurgical workers. Lots of ways are developed to remove inclusions from liquid steel. Gas injection is an effective one. This technique is used to achieve homogeneity in the temperature and metal composition and to assist in the removal of second phase and dissolved impurities from molten steel. Gas injection is commonly applied to the secondary metallurgy processes and continuous casting, for example the ladle argon gas treatment, RH vacuum degassing, and the gas injection in the Submerged Entry Nozzles (SEN) of continuous casting mold, etc. The development of these processes focuses on achieving two conditions: fine bubbles and good mixing. Fine bubbles provide a large gas/liquid interfacial area and a high attachment probability to inclusions, and good mixing enhances the efficiency of impurity transfer."

Jan 1, 2000

By Yoshisada Michiura, Junko Umeda, Katsuyoshi Kondoh

Rice husks or straws, one of the main agricultural wastes in South-east Asia, have a large possibility to be employed as usefully renewable resources to produce energy and high-purity silica (SiO2), because they consist of about 70% organics such as cellulose or hemi-cellulose, and 20% amorphous SiO2. The former is utilized as bio-mass energy; for example, thermal or electric energy, and bio-mass ethanol. High-purity silica can be used as raw materials in the industrial uses. It would be possible to extract silica elements from rice husks and straws by burning them in air because their main contents are organics. In the previous studies, a strong acid leaching treatment on rice husks before burning was carried out by using H2SO4, HCl and HNO3 to prepare high-purity silica materials. This was available to accelerate the hydrolysis of celluloses and hemicelluloses contained in rice husks, and remove the above metallic impurities. A strong acid leaching treatment, however, is significantly hazardous to environment and human life, and causes an increase of the process cost. In this study, the environmentally benign, harmless to human and economically effective process to produce high-purity amorphous SiO2 materials from rice husks has been established without using strong acids. From a viewpoint of the harmless influence on human body, the carboxylic acids were used in the leaching treatment on rice husks. TG-DTA measurement and GCMS analysis indicated that the leaching was effective for the hydrolysis of celluloses and hemicelluloses contained in rice husks at 473K~873K, which produced the same results in using the conventional sulfuric acid. The metallic impurities could be also removed from the husks via a chelate reaction between carboxyl groups (-COOH) and the metal elements. In particular, it was clarified that cadmium (Cd) were completely removed from rice straws by this reaction. Concerning the burning conditions of rice husks after the acid leaching, it was necessary to supply a suitable amount of air to completely combust organics; for example it required air supplement of 50 ml/min. or more. The burning temperature should be less than 1273K to obtain amorphous structured silica. High-purity amorphous silica materials with 99% or more were prepared from rich husks by applying the citric acid leaching treatment and burning process at 1073K in air.

Jan 1, 2008

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Elli Miettinen, Markku Lahtinen, Ilkka Kojo

"The recent trends of decreasing energy consumption and environmental emissions and utilization of economies of scale are strong drivers favoring continuous copper converting processes. Flash Converting benefits from low off-gas volumes and low investment and operational costs for off-gas treatment. Separate matte and blister furnaces allow the adaptation to concentrate quality changes and flexibility in layout and maintenance.The stationary blister copper bath in Flash Converting furnace is less aggressive to the furnace linings than agitated processes, resulting in low refractory consumption, long campaign life and high on-line availability.Copper Flash Converting has been successfully applied in Kennecott with a campaign life now exceeding five years. A second FCF was started at Xiangguang Copper in China in 2007. The process itself is proven, as its features are similar to those in FSF, Direct-to-Blister and Direct Outotec Nickel Flash Smelting (DON), with one significant difference: it is the easiest of all to operate.The paper presents differences between continuous Flash Converting and conventional converting based on recent experiences and studies."

Jan 1, 2009

By J. T. Stanley

The identification of crystal phases and crystal chemistry can be critical to understanding the mechanisms of waste material interaction with native soils. Understanding these mechanisms can suggest correct methods for remediation and treatment. A program is outlined and examples are given of the development of effective techniques for rapid phase identification of environmental samples using electron microscopy. The program concentrates on the development of integrated object oriented software to aid rapid searching of online databases and rapid simulation of potential crystal diffraction patterns. Examples come from dried sludge taken from a former hard-chrome plating facility.

Jan 1, 1993

By Michael D. Odekirk

The U.S. Bureau of Mines investigated solvent extraction methods for recovering scandium from water leach filtrates of sulfated tantalum tailings. These complex solutions typically contained 20 or more metals in significant quantities. Two commercially available organics, DEHPA and PC-88A, were identified as effective scandium extractants. The two organics were tested in continuous solvent extraction circuits to compare loading and stripping kinetics, recyclability, and general processibility. Results showed that 95 pct of the scandium, greater than 80 pct of the zirconium, and only small amounts of other solubilized metals were extracted. Scandium was stripped directly as a 3.6 pct Sc precipitate when a 3n NaOH liquor was used as the stripping agent. This precipitate was subsequently upgraded to 94 pct ScE3 via a selective HE leach.

Jan 1, 1993

By C. Anderson

Most applications of copper metallurgy are geared towards primary production. However, as recycling of materials is a growing industry, one future facility will rely on copper metallurgy as a means of processing precious metals. This paper will discuss the derivation of the proposed copper pyrometallurgical and electrometallurgical unit operations to be utilized in industrial recycling of secondary precious metals.

Jan 1, 1999

By D. J. Brennan

A techno-economic study is in progress, examining process and product options for treating smelter gases containing various concentrations of sulphur dioxide. Key contenders have been examined within an Australian context using the following criteria: * Markets for products * Capital Costs * Operating Costs * Waste streams generated Product options considered thus far are sulphuric acid, sulphur, calcium sulphite and gypsum. The development of an appropriate overall framework for evaluating process and product options is discussed and findings thus far presented. The emerging techno-economic study offers promise as a constructive guide to future policy decisions by industry and government.

Jan 1, 1994

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By G. P. Swayn

Recycling of dusts produced in a flash furnace by direct injection provides the opportunity to reduce recycle loads to the reaction shaft, lower fuel requirements and possibly increase metal recovery to products. Ausmelt has provided an Ausmelt lance system for injecting dusts collected from the waste heat boiler and electrostatic precipitator units, directly into the slag melt. This has been installed and operated in the Kalgoorlie Nickel Smelter with systems for feeding dust, for firing with oil and air, and for raising and lowering the lance. Modelling and testwork development of dust injection, results of commercial trials and design considerations for further opportunities of the Ausmelt lance system, are discussed.

Jan 1, 1994

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By Anita E. Lam

The thiosulfate leaching of gold generally requires the presence of a catalyst such as cupric tetraammine, Cu(NH3)42+, to obtain reasonable leaching rates and gold extractions. Unfortunately, this same catalyst that accelerates gold leaching also tends to accelerate thiosulfate oxidation to tetrathionate and other species. It is therefore imperative that a detailed understanding of the role of this catalyst and the factors affecting it is obtained. It is equally important for plant application that a method of assessing the catalyst be developed. In this work the role of the cupric tetraammine catalyst was studied using geochemical modeling for speciation prediction, thiosulfate leaching of gold ores, and chemical analyses of resulting leach solutions. It was found that the variables of pH, temperature, and the concentrations of ammonia, thiosulfate, and total copper all work in concert to affect the concentration of the cupric tetraammine species. It was also found that the presence of sufficient thiosulfate and cupric tetraammine was critical to the success of the leach.

Jan 1, 2003

By J. Y. Aubut

The modernization of the CCR Refinery to permanent cathode technology is presently underway. The 360,000 mt/y refinery is being retrofitted to accept the Kidd process. Part of this modernization includes the installation of Kidd stripping machines, and the total replacement of the materials handling equipment. It also involves the reinforcement of building structures to accept the new equipment and the ability to operate in different modes. The future equipment will interface with some existing apparatus, which is being retained for future operations. The whole operation will be automated and will allow product traceability for quality purposes. This retrofit poses important challenges given the size and scope of the modernization project and because it is being undertaken concurrently with normal plant operations.

Jan 1, 1999

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By Gary A. Campbell

This article is an analysis of world consumption of copper for the years 1976-1996. It is done to provide a comparison of what has happened over this time period with the trends of previous years in order to learn more about world copper consumption and to forecast world copper consumption trends into the new millennium. The analysis begins by documenting the geographic trends of consumption of copper for the years 1976-1996 by both region and key individual countries. Then, variables based on the intensity-of-use hypothesis and the intensity-of-use technique are selected and tested against the observed consumption behavior by using the correlation coefficient technique. The statistical results and their implications for the consumption of copper into the new millennium are discussed.

Jan 1, 1999

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999