Search Documents

By Susan Jacob

The heat of fusion of silver was measured using high temperature differential scanning calorimetry (HTDSC). Heating rate, sample mass, calibration standard and cover gas flow rate were varied to determine their impact on instrument accuracy and reproducibility. Good reproducibility was achieved in most of the runs. Accuracy was not satisfactory in most of the runs, though three runs gave results within 1.7%, 3.3% and 3.5% of the literature value, within the acceptable limits. A larger mass and higher heating rate tend to generate more accurate results.

Jan 1, 2006

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006

By Carlos Maurício Fontes Vieira

In the present work a ceramic body, fabricated using a mixture of clays and sand, for roofing tiles, produced in Campos dos Goytacazes, north of the State of Rio de Janeiro in Brazil, was characterized. Characterization was performed by X-ray diffraction, thermo analysis, chemical analysis, particle size distribution determination and plasticity. In addition, technological properties related to water absorption, linear shrinkage and flexural rupture strength were determined in samples fired at 700, 900 and 1100oC. The results showed that the investigated ceramic body has satisfactory plasticity and presents a refractory behavior during firing due to the predominantly kaolinitic nature of the clays.

Jan 1, 2006

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By Junji Shibata

Keywords: Synergistic effect, Solvent extraction, Nickel ion, extractant mixture Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni (II), 0.1 kg/m3 Fe (III), 0.01 kg/m3 Zn (II), 48 kg/m3 SO42-, 98 kg/m3 HPO32- and 31 kg/m3 lactic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods may be used for the treatment of this kind of solution. In this study, solvent extraction of Ni (II) is investigated by using two kinds of extractants in order to clarify the relationship between extraction equilibrium (static synergistic effect) and extraction rate (dynamic synergistic effect) for several extractant mixtures. The static synergistic effect does not take place significantly for the extractant mixtures of acidic extractants and neutral organphosphorous compounds, while a large static synergistic effect is confirmed when the extractant mixtures of acidic extractants and nitrogen-containing compounds are used. Nickel ions can be extracted in the wide pH range of 3.0-8.0 without any pH adjustment by using the several extractant mixtures. At the same time, the extraction rate remarkably increases by using the extractant mixtures of acidic extractants and nitrogen-containing compounds.

Jan 1, 2005

By Oliver Zach

To know as much as possible about the condition of the refractory material (lining thickness, slag layer, build ups, ...) in an high temperature furnace is very important due to the safety and economic impacts. The new CONSCAN system offers the possibility to measure the inner surface of an furnace, and based on this results to calculate the thickness of the refractory lining, slag layer, build ups,.... The CONSCAN System provides this results as figures and graphics. This system is also working under hot conditions so it is not necessary to cool down the furnace. Based on these results the process control and the refractory lining concept could be optimized for maximum campaign life of the furnace.

Jan 1, 2006

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By Mokka Rao, Asdrubal Serrano

"A mathematical model is developed which describes the movement of the minerals present where the vertical and angular velocities are related with the different operative parameters involved in the process of separation of silica from iron ore, which permit maximise the capacity of the spirals to obtain major productivity. The process is realised in two steps, of the rough dressing and other cleaning. Through the results obtained for chemical analysis of the final products of each spiral and the equation of movement of particles, it is proved the applicatibility and efficiency of mathematical model to operating parameters of the spiral. Moreover, it is determined though the recuperation of the final products of quality in the use spiral HC 1870 and HG 8/7. INTRODUCTIONThere is prospetive of increasing the production the iron ore in agreement with the demand of siderurgical proyects united with the external demand of quality 40 million tons per year. The Ferrominera de Orinoco Company is experimenting two types of modem spirals, Humprey (HC 1870) and Reichart (HG 8/7) which have limited capacity. For this reason this investigation designed a mathematical model with which larger units can be designed for increasing the capacity of the spiral."

Jan 1, 1999

By Chuanlin Fan

The process of flotation separation and recycling of spent potlining (SPL) was described. On the basis of the laboratory investigations, the effects of influencing factors in froth flotation process, such as grain size, flotation agent dosage, pH value, pulp density, and dissolved components concentration, etc, were carefully studied. And the influence on environment of the process was also discussed. It was found that flotation separation can be used as an environment-friendly method for treatment of SPL residue. Carbon and other compounds (include cryolite, sodium fluoride, calcium fluoride and diaoyudaonite, etc.) from SPL were separated and recycled as flotation products respectively.

Jan 1, 2009

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By Hirokazu Narita

Keywords: solvent extraction, precious metals, thiodiglycolamide, rapid separation, hydrochloric acid The solvent extraction of some precious metals (Pd(II), Pt(IV), Rh(III) and Au(III)) and base metals (Fe(III), Cu(II) and Zn(II)) in a hydrochloric acid solution was carried out using N,N'-dimethyl-N,N'-dioctyl-thiodiglycolamide (MOTDA) dissolved in the mixed solution of 80 vol-% dodecane and 20 vol-% 2-ethylhexanol. The extraction percentages of Pd(II) and Au(III) in the 0.01 M MOTDA-1.0 M HCl solution system are 99.6% and 71.8%, respectively. In contrast, the other metal ions are hardly extracted under the studied conditions. The Au(III) and Pd(II) extracted in the organic phase are easily back-extracted with a 1.0 M thiourea/1.0 M HCl solution. A comparison with the conventional extractant for the Pd(II) separation, di-n-hexyl sulfide (DHS), revealed that the extraction rate of Pd(II) with MOTDA is much greater than that with DHS. The extraction percentage reached over 99% in less than a 2 min contact time. However, in the DHS-Pd(II) system, it takes about 240 min to achieve the extraction equilibrium. Furthermore, MOTDA can quantitatively extract Pd(II) up to half the molar amount of MOTDA. Therefore, MOTDA is a promising extractant for Pd(II) from the HCl solution after the removal of Au(III).

Jan 1, 2005

By Andrey V. Tarasov

To carry out a physicochemical substantiation of a transition to ?soft? modes of reduction of calcine obtained by desulfurizing roasting of nickel concentrate produced as a result of copper-nickel converter matte separation in a nickel anode production circuit, an analysis has been conducted of the macrokinetic behavior of actual calcine samples in the presence of gaseous H2-CO mixtures and solid reductant additives. Within a temperature range of 900°C to 1100°C the main regularities typical of the calcine reduction process with individual gases (H2, CO) also take place when using a gaseous mixture. Under the conditions of low-temperature (900°C to 1000°C) nickel oxide reduction with products of fuel oil conversion in the presence of coke, the role of the latter is insignificant from the technological viewpoint. As a result of the present investigations, we have obtained analytical expressions of macrokinetic parameters of the reaction interaction within the [NiO] calcine-H2-CO-C-CO2-H2O-O2-N2 system.

Jan 1, 2005

By Fang Wu

The paper designs an extraction flow for the total recovery of nickel and cobalt and removing magnesium simultaneously from the cadthodic materials of the spent hydrogen-nickel and cadmium-nickel batteries. The separation of Co, Ni and Mg though P507 extraction .The extraction equilibrium pH is 4.5~5.0, ßNi/Co is 140~180, and ß Ni/Mg is 20~25; nickel and magnesium are scrubbed in two steps, in which the equilibrium pH of nickel and magnesium scrubbing is controlled at 5.0±0.1 and 4.4±0.1 respectively. The stepwise scrubbing technique is adopted to remove 94.5% of magnesium and to recover 99.45% of nickel and 95.35% of cobalt. During the integrated extraction and precipitation process the total recovery fraction of nickel and cobalt are 99.99% and 99.95%, and the recovery fraction of magnesium is 94.02%.The recovered NiSO4 and CoSO4 solution are enriched and crystallized.

Jan 1, 2009

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Chang-Dong Li

Cadmium ingot and nickel powder were prepared by high-temperature distillation, solvent extraction and liquid phase reducing method with spent Cd-Ni batteries as raw material. The impacts of the temperature in the distilling stage, the concentration of H2SO4 in the leaching stage, the pH value in the extracting stage and the dosage of hydrazine in the reducing stage were discussed respectively. The as- prepared samples were characterized by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic absorption spectrometry (AAS) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results showed that the recovering efficiencies of Cd and Ni reach 99.5% and 99.3%, and the purities of Cd ingot and nickel powder were higher than 99.90% and 99.80%, respectively.

Jan 1, 2009

By María Eugenia Castro, Silvia Galasso, Jorge Duca, Claudia Osuna, Ernesto Esparza

"We present a procedure for treatment of non-active solutions equivalent to the solutions obtained from dissolution of ionic exchange resins used in purification of a nuclear reactor primary cooling system containing Co, Ni, Cs and its isotropic varieties as main radioactivity source. Finally it is immobilized into a ferritic matrix by calcination which avoids its future leaching into environment.In order to achieve the objective of this treatment, a bivalent and a trivalent iron salt is added to the solution. Then, either a base or an acid is added, depending on the initial pH of the treated solution, with a Cs precipitating additive in order to reduce Co and Cs by precipitation, flocculation and adsorption. Controlling the amount of precipitating reactives it is possible to modify the activity/volume rate becoming a medium into a low radioactivity waste.The leaching test result applied over the ferritic sample is lower than the minimum limit established by law. Therefore, it can be kept safely in a interim storage."

Jan 1, 2008

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005