Search Documents

By Stankusm John C., Xiaoting Li

"Quantitatively identifying the load on a steel king beam set is a complicated issue in designing the king beam structure at the slope bottom area. From an engineering perspective, understanding the nature and support mechanism of the king beam structure as a standing support is critical in identifying the calculation input parameters for the structure design software. Based on design practices in recent years and successful applications in several slope bottom intersections, the authors present a king beam design methodology, including qualitative analysis, quantitative calculation with a structural design software, and computer Finite Element Analysis (FEA) verification.Especially important is the concept of interaction and the confinement effect between the king beam structure and surrounding rocks, which is essential in designing a proper steel structure in terms of maintaining the roof stability, as well as saving the steel materials and costs of manufacture, labor, and delivery. This paper details the design methodology and applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.INTRODUCTION AND DESIGN METHODOLOGYCurrently, the load on a square or arch set is typically determined by either past empirical design experiences or known heights of roof falls in current or adjacent mines. These methods work but sometimes are too conservative from an engineering perspective. For example, when designing a king beam structure for an intersection, these methods may lead to a design with extremely large and heavy steel beams, which are not convenient for delivery and installation on-site, not to mention, costly. Therefore, accurately identifying the potential maximum load on the king beam structure is important for designing a safet, effective, and cost-efficient steel structure. Based on past several years’ practices and fundamentals of ground control and structural design engineering, the authors propose a design methodology including the following components:The nature and mechanism of effective roof support (qualitative analysis),Ground reaction curve,Interaction and confinement effect between bolts and steel standing support and surrounding rocks,Factors affecting the load conditions of the king beam set"

Jan 1, 2018

By Paul C. Hagan, Jianhang Chen, Serkan Saydam

"Modified cable bolts are commonly used in underground mines due to their superior performance in preventing bed separation when compared with plain strands. To better test the axial performance of a wide range of cable bolts, a new Laboratory Short Encapsulation Pull Test (LSEPT) facility was developed. The facility simulates the interaction between cable bolts and surrounding rock mass, using artificial rock cylinders with a diameter of 300 mm in which the cable bolt is grouted. Furthermore, the joint where the load is applied is left unconstrained to allow shear slippage at the cable/grout or grout/ rock interface. Based on this apparatus, a series of pull tests were undertaken using the MW9 modified bulb cable bolt. Various parameters including embedment length, test material strength and borehole size were evaluated. It was found that within a limited range of 360 mm, there is a linear relationship between the maximum bearing capacity of the cable bolt and embedment length. Beyond 360 mm, the peak capacity continues to rise but with a much lower slope. When the MW9 cable bolt was grouted in a weak test material, failure always took place along the grout/ rock interface. Interestingly, increasing the borehole diameter from 42 mm to 52 mm in weak test material altered the failure mode from grout/rock interface to cable/grout interface and improved the performance in terms of both peak and residual capacity.INTRODUCTIONFully grouted cable bolts have been used in underground mining industry for many decades. Initially, plain cable bolts manufactured by winding seven flexible steel wires together were commonly used (Thorne and Muller, 1964). Laboratory and field tests lead to a better understanding of the transfer process between grouted cable bolts and the surrounding rock mass, which is beneficial to improve the reinforcing performance of cable bolts in engineering practice (Fuller and Cox, 1975; Cox and Fuller, 1977; Schmuck, 1979; Stillborg, 1984). Nevertheless, as in many cases the initial cable was sourced from discarded steel with a smooth surface along the strand, plain cable bolts did not always meet performance expectations (Windsor, 1992). Over time, it was realised that cable surface geometry plays an important role in determining anchorage performance. Consequently, modified forms of cable bolts were developed. For instance, twin-strands which were made by using spacers to combine two plain cables together improved anchorage capacity two-fold (Matthews, Tillmann and Worotnicki, 1983). However, this required a large borehole to be drilled. Epoxycoated strands had remarkable performance in practice but were difficult to install without damaging the epoxy layer (Dorsten, Hunt and Kent, 1984). In the 1990s, there was a rapid development in the cable bolt design. A typical example was birdcaged cable bolts. They were initially suggested by Hutchins et al. (1990) via unwrapping traditional seven-wire strands and generating a number of nodes together with antinodes along the strand. But it was difficult to make birdcaged cable bolts that could be coiled for transporting."

Jan 1, 2015

By Winton Gale

"Rock and coal fractures and micro seismic vibration are common occurrences during development mining. It is very uncommon for coal and rock to be propelled into the roadway during normal mining operations. However, such occurrences do occur and appear to require significantly more energy than is available from strain energy release during coal cutting. The sources of energy, which can contribute to the propulsion of coal from the face or ribs, are typically strain energy from the surrounding ground, seismic energy from a rapid rupture of the ground in the vicinity, or rapid expansion of gas from within the burst source area.The aim of this paper is to briefly review the bursts that could be related to strain energy or seismic energy. However, the greatest emphasis is placed on the effect that gas within the coal could play in moderate to gassy mines.It has been found that the bursts related to the expansion of gas can occur in coal and stone. The volume of gas involved in coal bursts is typically lower than in gas outbursts; however, the process is generally similar.INTRODUCTIONA coal burst is defined as a rapid expulsion of coal (and potentially gas) from the boundary of the roadway. The volume of a burst can be variable, but volumes above 10-50m3 are noted and cause significant disruption to operations.Rock and coal fracturing is common about roadways, particularly under the influence of elevated stresses, either tectonic or related to mining abutment stress. Shear fracture is very common; however, it is very uncommon that the coal is propelled from the face or ribs as a result of fracture of the material. The nature of rock fracture about roadways under elevated stress is presented in Figure 1.A burst requires energy to propel the coal or rock from the rib or face of the roadway. The depth of material impacted may vary from 0.5m to greater than 3m inside the roadway boundary. The strength of the ground in this zone is variable depending on the nature of the coal seam (or surrounding material). Typically, this material has significant residual strength as confinement increases into the ribside.The energy required to propel this material is typically in addition to that which is associated with normal fracturing about the roadway."

Jan 1, 2018

By Weihua Song, Hongwei Zhang, Feng Zhu, Sheng Li, Guoshui Tang

"Rock burst is one of the most serious dynamic disasters in coal mining. Rock burst prevention involves two difficult tasks: systematically evaluating the occurrence conditions and effectively forecast for rock burst. This paper systematically studies the effects of natural geological dynamic conditions and mining engineering on and forecast for rock burst. It establishes the evaluation method and index system of rock burst geological dynamic conditions and proposes a method of forecasting rock bursts by monitoring fault activity with anchor cables. Natural geological dynamic conditions are a necessary condition while mining engineering is a sufficient condition for the occurrence of rock bursts. Rock bursts in mine must have suitable geological dynamic conditions, and mining engineering activity is merely an inducing factor. There is a good correlation between anchor cable stress variation and fault activity, when the anchor cable dynamometer indicates that the fault is active. It can forecast a rock burst a few days in advance. This technique has been successfully applied to Panel 83003 of a coal mine in China, which improved the safety production level of the mine and found a new way of rock burst evaluation and prediction.INTRODUCTIONRock burst is one of the most serious dynamic disasters in coal mining. With the increase of mining depth, rock burst disaster is becoming more and more serious. Systematically evaluation and effective forecasting of the occurrence of rock burst in the coal mines are important and difficult work in the control of rock bursts. Chinese researchers have performed numerous researches on rock bursts, Qi et al., established the rock burst model of frictional sliding instability, explained the occurrence mechanism of rock bursts by stick-slip phenomenon in frictional sliding, gave full consideration to the influence of primary rock stress and mining-induced stress on rock burst occurrence, and proposed the stress controlling theory of rock burst. Pan et al., [3] put forward the criterion of perturbation response, explained and analyzed the problem of rock burst in circular openings, put forward the ratio of coal-rock elastic modulus and reduced modulus is the significant parameters for the determination of stabilization; systematically summarized the rock burst distribution, type, mechanism and control in China. They classified rock bursts into three types: coal compression, roof fracture and fault movement. By applying energy transfer principle and conservation of energy, combined with the analysis of the weakening of rock fabric damage, Zhou and Jiang put forward the theory and equation for the occurrence of coal-rock mass impact effect. They analyzed and discussed the formation mechanism of rock burst by combining impact effect theory and energy equation. Wang et al., recognized that the mechanism of rock burst which induced by fault, fold and phase transition is the superposition of tectonic stress and mining stress and that the axes of syncline and anticline and their flanks are the location where rock bursts mostly occur. To prevent stress superposition is the efficient way to control the structural rock burst [7]. Jiang et al., summarized the research achievement of rock burst mechanism and controlling techniques and existing problems in recent years in China, and pointed out the direction to improve the level of prevention of controlling rock bursts in coal mines."

Jan 1, 2015

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By Xianxin Shi

In surface electrical exploration the high resolution earth resistivity method (HRRM) is a very effective method for detecting abandoned drift mines workings. When the abandoned mines are more than 500 ft (150 m) deep, its detection capability reduces greatly and requires more effort to implement. In Yan Quan coal mine, Shanxi province, we tried to adapt this method for underground application. Two survey lines were designed with the spacing of current and potential poles 20 m and 10 m, respectively and measuring points at 2m. The measurement radius of I line and I1 line were 140 m and 60 m, respectively, and the infinitely far pole was 1200~2000 m from the survey line. (Note the I and II lines are located on the north and south ribs of main tunnel, respectively). The survey results showed that abandoned workings were located at 25-70m, Survey Line I and at 80-1 10m, Survey line 11. Based on this finding, the longwall panel gateroads and set up entry were properly located thereby providing safe mining of the No. 15 Coal seam. Key Words: Abandoned coal mine, High resolution earth resistivity, Underground electrical exploration

Jan 1, 2005

By S. Mehrdad Heidari

The concentrator plant is located near a very high (105m), large (- 500m) and steep (a, > 45' ) wall. Geologically, the wall was composed of very complicated formations and broad range of soils and rocks type in which a variety of local typical failures models have been occurred on different soil and rocks formations. The construction of concentrator plant structure and other activities have been overshadowed by these local failures. Safety and risk of huge failures were serious concern. For distinguishing the wall conditions a broad campaign of slope stability investigation with detailed geotechnical drilling on berms of wall have been done and the structure of slope was fully identified and further Lab tests and slope simulation models done. Slope stability of the wall was analyzed and the effects of instability factors were described in short term (for construction phase) and long term (for production phase).The results indicated, if a well-appointed drainage system is implemented, the overall stability of the wall in short term will not cause any particular problem but about long term stability, the wall must be supported by rock bolting, consolidation grouting, shotcrete reinforced with fibers. The results have been confirmed by passing one year after this investigation.

Jan 1, 2005

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain- softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OBAB) ratios of less than 5, interactions do not occur, and that for OBAB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OBIIB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

Jan 1, 2005

By Ross W. Seedsman

The feasibility of 6 m high single pass longwalling has been studied using Newlands Mine as a case study An intensive geological investigation identified a range of hazards but a mine layout was possible that minimised the risks with respect to joints, cleats, angular bedding, coal shears and horizontal stress. Geotechnical design input was required for support capacity, subsidence, gate to face transition, face span, and roof support. It is concluded that longwall face equipment can be made available by modifying existing designs, gate to face transitions will require a number of steps, and a mid-face sprag should not be required for routine operations.

Jan 1, 1992

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By Xu Linsheng

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including modelling.

Jan 1, 1992

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By Andre Zingano

It is known that the backfilling confinement increases the pillar strength and also reduces the rib lateral displacement. With backfilling, it is possible to increase the room-and-pillar mining recovery. This paper aims to study the behavior of coal pillars confinement using rock fill as backfilling material. Laboratory tests were carried out to determine the behavior of backfilling materials. Constitutive models were developed for the tested backfilling materials. Numerical simulations for the effect of backfilling materials on the ground stability in room-and-pillar coal mine entry were performed. The backfill method is a good strategy to (i) improve the ground stability in room-and-pillar coal mines for long term, especially for weak coal seams, (ii) increase the coal mining recovery and (iii) reduce the quantity of waste material on waste piles at the surface.

Jan 1, 2011

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011