Search Documents

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

Floor heave events in underground mining often happen suddenly and cause risk to workers and equipment. Reducing the risk of floor heave must be addressed in mining layout design. To improve that design one must understand the significant parameters that are correlated to the occurrence of floor heave. To accomplish that goal, researchers from the National Institute for Occupational Safety and Health (NIOSH) completed a numerical study using FLAC3D, taking advantage of its strain softening and ubiquitous joint capabilities to better simulate the floor heave and caving mechanisms involved at an actual mine site.

Jan 7, 2020

By Louis W. Cope

Since its discovery, Cuba has been called the “Pearl of the Antilles.” The country remains that, albeit a little tarnished these days. In Havana, many of the buildings are being refurbished, while some new ones are under construction. Since 1991, the laws have been relaxed so that Cuba is developing a mixed economy of central control with free market. Joint venture agreements have been signed with businesses from many countries. This does not include the United States due to its embargo. But even these regulations have been relaxed some.

Jan 1, 2003

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator's compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator's location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines' involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By G. Récoché, A. Chamaret, M. O’Connor

Building indicators that respond to all stakeholders' needs is a time-consuming and complex exercise, with certain questions still unsolved. The aim of the current three-year research project, carried out in partnership between BRGM’s Mineral Resources Division and C3ED, is to propose a top-down / bottom-up indicators building methodology that combines conception and coordination methods and a participative approach. The tool-design phase is based partly on a comparative analysis of existing international initiatives according to different criteria (objective, observation scale, framework, etc.). The study of two African mining projects will provide the opportunity to confront the conceptual aspects with reality in the field. Careful consideration of the participants’ suggestions will result in a set of indicators that can be easily understood and adopted by all stakeholders. The final objective is to measure the impact of a mining site on a local, regional and national sustainable development frame, throughout the full life cycle of a mine.

Jan 1, 2005

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008