Search Documents

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By O. A. Lima

Effective solids suspension is a necessary precondition for particle collection, and solids suspension is largely dependent on the hydrodynamics of the flotation cell. This study attempted to correlate the status of the suspension of apatite particles of different sizes in a Denver laboratory flotation cell versus the impeller rotational speed (N) adopted to operate the machine. The latter variable (N) influences the impeller capacity to lift the particles from the bottom of the tank and also to disperse them throughout the volume of the vessel. Such an impeller capacity can be characterized by the critical impeller speed for the accomplishment of solids off-bottom suspension (Nz) and also by the velocity of the radial water flow discharged by the impeller (U) divided by the particle terminal settling velocity (Us). This way, the status of the suspension of apatite particles inside the flotation cell can be characterized by one of three categories: ?segregation? (N/N2 < 0.60 and Us/U > 0.08); ?suspension? (0.60 = N/N2 < 1 and 0.06 < Us/U < 0.10); and ?dragging? (N/N2 = 1 and Us/U = 0.03). The range of impeller rotational speed (N), which was able to suspend the finest particles (Dp = 90 µm), was unable to suspend the coarsest particles (Dp = 254 µm). Conversely, the high value of N (N > 1,300 rpm), which is adequate to suspend the coarsest particles, may promote the entrainment of the finest particles to the froth layer.

Jan 1, 2009

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By C. Guan

Since it was patented in 1942, the Crago process with fatty acid rougher flotation followed by deoiling and amine cleaner flotation has become the standard for phosphate flotation in Florida and North Carolina. This paper outlines the basic fundamentals involved in this proven technology. Included are the mineralogy of the flotation feed, the solution chemistry and the interfacial phenomena. The process variables affecting the performance of this technology are also discussed.

Jan 1, 2009

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

By S. Vivek

An Atomic force microscope (AFM) was used to measure the surface forces between hydrophobic silica surfaces. The measurements were conducted in the presence and absence of Cu(II)species in solution to study the effects of the cation adsorption on the hydrophobic force. The results obtained in the absence of the Cu (II)species showed that the hydrophobic force does not change with pH, while the electrostatic repulsive force changes substantially with pH. In the presence of the Cu(II) species, the hydrophobic force begins to decrease at a pH where Cu2+ions are hydrolyzed, indicating that the first hydrolysis product (i.e., CuOH+ions) are the species adsorbing on the surface of the hydrophobic silica. The results of the surface force measurements were used to develop a model for the adsorption of the hydrolysis product of Cu(II) species on the hydrophobic silica.

Jan 1, 2003

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today&apos;s apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery&apos;s capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003