Search Documents

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By X. Song, Q. Zhang

"The development of fracture zones in surrounding rock mass has significant impact on the stability of underground mine roadways. Detection of the fracture zones is of compelling importance for maintaining roadway stability as well as for safe and speedy excavation of the roadways. This paper presents a study conducted at Dong Bao Wei underground coal mine, where the roadways were developed in diabase rock mass. The roadways suffered severe damages, including sloughing and excessive floor heaving. The borehole imaging technique was applied in the study to observe and detect fracture zone development surrounding the roadway openings. Based on the borehole imaging studies, new roadway support systems were proposed to improve the stability. INTRODUCTION At the Dong Bao Wei Coal Mine three main roadways of the west wing were excavated. The three roadways had semicircle arch cross sections and were at a depth of 650 meters, each being about 750 meters in length. The roadways were driven through a section of thick diabase intrusion, which was softened by water with reduced strength and may turn into powder form under weathering. Site investigation indicated that the roadways in diabase intrusion zone were badly damaged due to severe deformation, and very serious roadway sidewall sloughing and spalling accompanied by severe floor heave often occurred.(Figures 1 and 2) In order to ensure the normal use of the roadway, undercuts were excavated. However, this operation seriously affected the roadway construction progress and increased the amount of roadway support operations as well as the roadway maintenance costs. Furthermore, a roof fall accident occurred in nearby drilling site. The investigation indicated insufficient support provided for the roadways which imposed significant safety hazards and would have serious impact to mining production and subsequent mining activities.The support of the main roadways is a critical task and is the focus of the underground opening excavation work at the mine, since more than 40 years of service life is required from these main roadways. For these roadways, large cross sections with high degree of stability and minimal amount of deformation should be maintained. Therefore, providing sufficient and appropriate roadway supports is of significant importance to the coal mine. In this paper, in order to optimize the roadway supporting system, studies were carried out on the geological structures, lithological characters, roof bolt anchoring features and suitable anchoring layers. The studies were aimed at ensuring the stability of mine roadways, reducing the roadway maintenance costs and providing a safe mine passageway for orderly production and progressive development of the mine"

Jan 1, 2016

By C. E. Jordan

The Bureau of Mines investigated a simultaneous elutriation and flotation technique for separating polyethylene terephthalate (PET) from polyvinylchloride (PVC). The Tuscaloosa Research Center, through a cooperative agreement with a recycling company, devised an elutriation-flotation method for beneficiating the mixed heavy plastics portion of municipal solid wastes which is composed of polystyrene (PS), PET, and PVC. A sodium carbonate brine was used to remove the lighter PS from the heavier PET and PVC. Over 98 pct of the PS was recovered in a high purity PS concentrate containing 99.7 pct PS, The remaining PET and PVC mixture was washed to remove the brine salts that would be harmful to the flotation process. The clean PET and PVC mixture was conditioned in a solution of 45 g/t gelatine and floated in a short (l-m) column flotation cell in an upward flow of water. In a single flotation step, over 75 pct of the PET was recovered in a high purity product containing 99.8 pct PET. The bubbles attached to the PET lowered the effective density of the PET-bubble agglomerate and allowed successful separation of these agglomerates from the PVC plastic pieces. This method separated two-thirds of the mixed plastics fraction into high purity PS and PET products suitable for recycling and left only one-third of the plastics in the mixed plastics product.

Jan 1, 1992

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By S. Makni, F. Wang, A. Rosa, B. Klein, C. Saud, R. McIvor, A. Kumar, C. Gagnon, D. Gong

In response to the Natural Resources Canada “Crush It Challenge”, Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling, with high-pressure grinding. Two plant case studies, a small tonnage gold recovery operation, and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed set up to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of highpressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone, and final stage total circuit energy savings, exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Mar 2, 2022

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

Large mining-induced seismic events and their aftershocks cause hazardous working conditions, damage infrastructure, delay production and pose a risk to miners in the deep-level gold mines of South Africa. Stress changes affecting pre-existing zones of weakness are the main drivers of large mining-induced seismic events, which are often followed by aftershocks triggered by quasi-static stress transfer within the rockmass. A better understanding of seismic source mechanisms is important if the seismic data is to be used more effectively for mine planning and to reduce the rockburst risk. Four large seismic events (ML≥2.0) associated with the mining of the Ventersdorp Contact Reef (VCR) at Kloof Gold Mine occurred on 13 June 2017. The events and their fore- and aftershocks were studied in detail to establish the circumstances and the cause of the incidents. The local magnitudes ranged from ML 2.3 to ML 3.0, the seismic moment from 0.69 to 2.25 x 1013 Nm and the source radius from 92 – 150 m. The main shocks were preceded by foreshock sequences, which were especially vigorous in the four hours before the main shock. Seismicity was recorded by in-mine arrays of three-component 4.5Hz geophones (detection threshold approx. ML -2.9). Following all four main seismic events, ML 2.3, ML 2.3, ML 2.9 and ML 3.0, the network detected a total number of 300 aftershocks ranging from ML -2.9 to ML 1.6 spread within a 1300 m radius from the centre of the seismic network. The statistical properties of the aftershocks were analysed using three scaling relationships: (i) Gutenberg–Richter frequency magnitude relationship; (ii) modified Omori’s law; and (iii) Båth’s law for the magnitude of the largest aftershock. The geological or mining feature that controlled the failure (e.g., fault, dyke, pillar, abutment) was determined by calculating the orientation of the nodal planes of the large seismic events using moment tensor analysis and studying the aftershock distributions.

Apr 26, 2022

SOLUTION MINING Solution mining techniques present a means of extracting soluble ores, particularly such materials as salt and potash, from horizons which are not accessible by conventional mining. In the process of dissolving materials, it is evident that solution may be complete or partial. In general, the solution mining operations described in the following section relate to complete solution of the desired compound. Even though the solution of material is complete, there may be instances in which insoluble material is present to a large extent either as granular separated particles or as insoluble layers. The process required for obtaining the desired product involves access wells to reach the deposits, sufficient water supply to yield the production goals, and the development of an underground cavity. The process of solution mining, therefore, depends to a great extent on three factors: availability of a relatively pure strata or formation of salt or potash to be mined, access well or wells, and adequate control of the solutioning process so that enlargement of underground cavities can be fairly well delineated. Since halites represent the most general ores mined by this procedure, the considerations which follow are based primarily on the production of sodium or potassium chloride. The producing formations may be in the form of bedded evc~porites wherein the salt member may be some 30 to 500 ft thick or from salt domes in which great depths of salt occur. Solution mining has been carried out to depths of nearly 10,000 ft. The recovery of saturated brine from wells drilled to effect the solution-mining process leads to further processing. In many instances, the procedures are relatively simple and involve simple recrystallieation or fractional crystallieation, while in others more complex flow systems are required before a final product is obtained. The intent of this section is to provide information relative to the basic procedures for obtaining materials which are soluble in water and to acquaint the engineer with the various aspects of the overall problem which in many instances, may become quite complex and present numerous difficulties. The storage of fluids, particularly hydrocarbons, underground has proven to be a very important part of industry operations. Cavities formed in salt provide excellent storage facilities. The formation of well-defined controlled configurations of such cavities has been possible because of better understanding of the solution process, wide experience gained over nearly 30 yr, and improved technology in drilling and completing wells, surveying caverns, and the operation of numerous types of systems. Solution mining techniques will improve in the future. Many facets of the simple operation of pumping solvents and extracting valuable minerals require further study. Developments undoubtedly will occur to further the processes of mining by solution. In addition to those whose names appear in connection with the individual subjections which follow, a major role in assembling and processing the material in this section was played by Dr. D. A. Shock, Central Research, Continental Oil Co., Ponca City, Okla.

Jan 1, 1973

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By Glen L. Black

Choosing a mining method for an underground orebody is a complicated and often iterative process. Advances in technology have given design teams an array of possibilities for methods and equip¬ment. Hecla Mining's discovery of the deep Gold Hunter ore body challenged the staff at the Lucky Friday Mine to determine the optimum mining method. Taking an ore body from prospect to production requires traditional resource characterization. This includes drilling, delineating and modeling. Developing the mining plan is an evolving process, changing with each new piece of in¬formation as the project progresses through exploration and development. The Gold Hunter deposit is a steeply dipping vein system in the Wallace Formation of Idaho's Coeur d'Alene mining district. Gold Hunter is a misleading name for the ore body. The vein is a silver-rich, lead-zinc deposit with only traces of gold. The Gold Hunter ore body is located about 1.6 km (1 mile) north to northeast of Mullan, ID. The ore body is mined from the Lucky Friday Mine, located 0.4 km (0.25 miles) east of Mullan. Mining began on the vein from an access drift driven from the Lucky Friday Mine's 4900 level. Production from the ore zone is projected to be 771 t/d (850 stpd). The Gold Hunter ore is combined with Lucky Friday ore and milled in the Lucky Friday mill. The combined ore boosted Lucky Friday's 1998 silver production from 62.2 t/a (2 million oz/year) to more than 124.4 t/a (4 million oz/year).

Jan 1, 1999

By Richard J. Goff

Technical Support, one of several major organizational units in the Mine Safety and Health Administration, provides technical assistance to the mining community in all areas of health and safety. One of its many areas of expertise is noise control. Depending upon the needs of the operator or inspector, the services provided can range from locating major noise sources to actually building noise controls. Over the years a vast amount of knowledge has been obtained as to what will work and what will not. DESIGN GOALS While many noise controls have been developed for mining equipment and operations, the most acceptable (ergo successful) have achieved the following design goals: - a noise level reduction of at least 5 decibels; - minimum interference with production; - inexpensive to install; and - effective in reducing low frequency noise.

Jan 1, 1984

I am deeply honored and grateful to receive the prestigious Gaudin Award. Frankly, I find myself amazed to be included in the company of those outstanding individuals who have previously received this recognition. I am humbly honored to receive this award from an industrial research group. Gaudin was an internationally respected leader of mineral processing. His research contributions widely covered the whole spectrum of mineral processing science and technology, including comminution, size distribution, electrostatics, magnetics, thickening and, especially, the development of flotation theory and application. In his later career, he increased his emphasis on hydrometallurgical technology. In fact, one of his most notable practical contributions was in the development of leaching and ion exchange purification of uranium from low-grade ores. Gaudin catalyzed the trend in mineral processing toward engineering science for a better understanding of process mechanisms and kinetics. He said that those working in academic fields should have an underlying responsibility to the industry they represent. This imposed on him the objective of seeking out research areas that had some relevance to industry's problems. He said, "research without an audience cannot survive." Gaudin performed a most vital service, both in the areas of research in which he was actively involved and through his less-direct influence on current research by his many former students and their students in turn. Interestingly, Gaudin's strength has influenced Newmont Mining Corp. His favorite student was Plato Malozemoff. He had a long and distinguished career with Newmont, beginning as staff engineer in 1945, serving as Newmont's president for more than 30 years and as chairman of the company for 20 years. Newmont's greatest growth occurred during his leadership. Another one of Gaudin's graduate students from Montana School of Mines, Oscar F. Tangel, joined Newmont in 1967. He was a vice president of research and development until 1986. In their efforts, Newmont built a research group, developing the technologies of exploration, geophysics and metallurgy. The Newmont technical facility is named in honor of Malozamoff as "a leader in the development and implementation of new technologies." The mining industry is facing very difficult times, especially in the metals industry. Most metal prices have declined and are still not stable. Most domestic mining companies have largely done away with in-house research and development. Many are reluctant to invest in technology development for which there is not an immediate need. The metal mining industries are focusing on reducing operating costs to survive. Newmont is in the same situation. I appreciate that Newmont's management believes in the importance of research and technology and the impact technology has on the company's value. At Newmont, technology development involves working in the area of applied research. The connections from academic fundamental research to applied research and finally to process development and implementation are very important to develop a new technology. Fundamental research is our foundation, our guidance, giving us direction, providing the principal and mechanism and understanding why it works. Understanding the why will lead to further innovative development. Applied research needs to find the approach to reality, how it works, how to make it better and how to commercialize it. Process development and implementation needs a strong leadership, requires long-term commitment, makes improvements in practical engineering and finally develops an economically favorable process. Implementation is the most important stage in making research a reality. Each stage needs to give feedback to the other stages. Problems need to be understood and solved. Otherwise, the new technology will go nowhere. Simplicity of operation is a key of success in any plant. Necessity is the

Jan 1, 2002

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines paper to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios are prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By R. Mensah-Biney

The kinetics of gold-bromide loading onto activated carbon has been investigated in a batch stirred reactor. The amount of gold adsorbed by the carbon was correlated with time based on a second-order equation. The rate constant for gold-bromide species onto activated carbon ranged from 0.27 to 1.2 x 10-3 (kg/t)-l(min)-l from a solution containing 25 ppm of Au, with 0.8 g carbon per liter of solution at 30° C. The equilibrium saturation capacity (Q.) was 36±3.0 kg/t from the same system. The rate of loading increased with decreasing particle size, decreasing pH, increasing temperature, and decreasing concentration of gold in solution. The calculated activation energy E. was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Q.) increased with increasing concentration of gold in solution, but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1996

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,300 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for the mining designs and operations in the Leeville underground mine.

Jan 1, 2010

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By Brianna Eiter, Max Barham, Tim Bauerle

Fatigue-related risk is a persistent safety concern for the mining industry. However, fatigue and sleepiness are often treated interchangeably, which can lead to confusion and potentially less effective reduction of safety risk. To provide clarity, we present an overview of similarities and differences between work-related fatigue risk and sleepiness including definitions, theories, measurements, and mitigation strategies. As a supplement, a summative visual model which highlights these similarities and differences is presented. Expanding industry knowledge in this area will assist safety professionals in crafting more targeted risk management practices appropriate for work-related fatigue risk, sleepiness, or both.

Dec 19, 2023