Search Documents

By Richard C. Corson

The objective of blending materials in a bedding pile is to reduce the variation in successive samples taken from the materials to be blended. In designing a bedding and reclaiming operation, several mechanisms are available to effect the reduction of variability, or increase in homogeneity, of the materials. These mechanisms can act before stacking, in the stacking process, in reclaiming and after reclaiming. In evaluating alternative methods of stacking and reclaiming, the potential user must judge each method on the basis of certain criteria; the capital cost of the equipment, the allowable absolute variability of the reclaimed product and the effectiveness of blending. Several stacking and reclaiming methods have been tested using a computer simulation. Based on the results of this program, factors were developed to describe the effectiveness of blending for chevron stacking of discrete materials and preblended materials, bucket wheel reclaiming and drum reclaiming. From these factors, the total effectiveness of a combined stacking and reclaiming system can be determined.

Jan 1, 1985

By Jean-Michel Rendu

In most mining operations, some degree of selectivity is applied. Whether one deals with surface or underground operation, ore zones, and waste zones are defined not only on the basis of the value of the ore contained, but also taking mining constraints into account. A number of computer techniques are presented which can be used to determine the optimum location of the footwall and hanging wall of ore zones intersected by drill holes. Minimum mining width and minimum internal waste width constraints are taken into account, as well as other economic constraints. The system is presented as an integral part of a larger manumatic ore reserve and mine planning system.

Jan 1, 1982

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By William F. Stowasser

The United States has traditionally been the world's largest producer and net exporter of phosphate rock and related fertilizer products with the exception of rock exports from Morocco. In recent years, however, U.S. producers have faced increasing competition from operations in foreign countries, leaving the future position of the U.S. phosphate .industry as a leader in the world markets somewhat less certain. This paper will review the U.S. phosphate rock industry in relation to its known demonstrated reserves, its historical and present production and export levels, and its future mining potential. The paper will include an analysis of the availability of phosphate rock in the United States represented by cost-tonnage relationships. The U.S. phosphate rock industry has for decades provided raw materials at reasonable costs to the phosphate fertilizer industry, and the fertilizer products have been made available to both domestic and international markets. Natural soils normally contain low quantities of phosphorus, and cultivation exhausts the available phosphorus through the removal of harvested products. Yields diminish, and it becomes necessary to apply phosphorus to the soil in an amount at least sufficient to compensate for removal. Raising the level of phosphorus also permits nitrogen and potash fertilizer nutrients to be effective and sustain the high crop yields necessary to support increasing food demands. In only a few areas of the world are soils, climate, rainfall, and low-cost phosphate fertilizer available to assure high agricultural yields in successive years. One of these areas is the central United States and south central Canada. By contrast, in the Soviet Union, the weather conditions in farming areas frequently cause crops to either bake or drown in the field. To attempt to counter the effect of weather on production, the U.S.S.R. has increased use of fertilizer and equipment in recent years. The effect of fertilizer on various crops has been documented, and in all cases, improvements in yield and plant development were noted, as was the ability of fertilizer to mitigate the effects of unfavorable climatic conditions. Phosphate resources can be classified as either identified or undiscovered. In the identified classification, we are principally concerned with demonstrated phosphate resources, or those that have been measured or indicated. In the southeastern United States, the phosphate mining areas of Florida and the Carolinas have been explored and drilled extensively in attempts to locate new deposits. The exploration programs indicate that another Florida Bone Valley Formation or North Carolina Pamlico River Deposit is unlikely to be discovered in the southeastern U.S. coastal plain. Phosphate rock deposits of commercial interest in the western United States are located in Montana, western Wyoming, northern Utah, and southeastern Idaho. The deposits are in the Permian Phosphoria Formation with most of the mining activity occurring in Idaho. Although substantial demonstrated resources have been identified, recovery costs and the field's isolation from markets have restricted growth of the industry in the west. The phosphate rock deposits in Tennessee are well known, and it is estimated that about 29 million metric tons1 are potentially recoverable. Undiscovered deposits of brown rock in Tennessee would likely be quite small.

Jan 1, 1985

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By JÖRG DEHNERT, PETER WINDISCH, Bernd Schönherrt, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposures of miners in Germany, especially during remediation work in old mines. The QESS is a light-weight, modular, and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil, and expanding foam. It is designed to seal off radon-rich parts of galleries within only a few minutes. Originally, the QESS was developed to protect miners against radon exposures. Then, the QESS found the attention of several mine rescue teams at a German mining conference. The Student Mine Rescue of the Technical University Bergakademie Freiberg and the Wismut Mine Rescue carried out firstmine rescue drills in Freiberg and Schlema. Additionally, a mine rescue drill was carried out by the Front Range Mine Rescue in the Edgar Experimental Mine of the Colorado School of Mines. These drills helped to improve the systemand highlighted its potential for mine rescue operations. Now, the QESS is wellsuited for small-scale mining. The QESS can be used to seal off galleries in only a few minutes to both protect miners fromradon exposures and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

Jul 23, 2020

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By Eric Sitorus, Septian Prahastudhi, Roy William, Wieda Azani

In July 2020, massive slope failure occurred in the southeast corner Grasberg open pit. This was the final episode in the breakthrough of Production Block 2 South (PB2S) of the Grasberg Block Cave to connect to the surface. This breakthrough had been rapidly evolving during the first half of 2020 and occurred as expected with no adverse impacts to safety or operations. To manage and safeguard the exposure to the workforce and operations, numerous hazards were identified and anticipated. The failure of the sill pillar between the open pit and PB2S cave was identified as the main area of interest and was closely watched during the failure process. This paper reviews the systematic approach developed to convert monitoring data into information around the collapse of the GBC PB2S cave sill pillar. The data that was interpreted consisted of micro-seismic, piezometric, ground-based radar and observational inspections. Geological structures on the boundary of the PB2S cave were clearly involved in the breakthrough process. As the cave propagation reached these structures and triggered instability, the resulting acceleration and breakdown were clearly shown by IBIS radar units associated with high movement in the slope. The focus of this paper is on the evolution of changes seen in the micro-seismic data and how it was used to understand the rapidly changing conditions of the sill pillar. The seismic parameters evaluated were event distribution, Es/Ep value, and the seismic moment tensor inversion. The changes of breakthrough indication seen in these parameters were substantiated by Shear Wave Splitting (SWS) analysis that showed a close correlation with the fractured zone above the PB2S cave as indicated by the increasing anisotropy.

Jan 1, 2022

By L. H. E. Weyher

Minerals beneficiation commonly requires initial crushing and grinding so that the mineral phase we seek to concentrate is adequately liberated to obtain a product of specified grade at optimum recovery. To some degree this also is true for coal preparation. In the comminution process we liberate not only the product but also the tailings phase. The true objective is, therefor, to eliminate from the comminution circuit whatever particulate matter has reached specified liberation, regardless of whether the particle is product or tailings material. Overgrinding either of the two phases ties up mill capacity and usually also burdens the downstream processing steps by increasing costs or decreasing recovery, or both. In view of this situation, one would expect concentration steps to be commonly incorporated into the cominution circuit. The reasons this is not done may vary, but probably include the desire to utilize large scale unit operations, e.g., large mills, in conjunction with very simple processes. Hydrocyclones have satisfied this desire but may not always be employed for the right reasons. Hydrocyclones are indeed simple. They also are rugged and forgiving. Unfortunately, these virtues are frequently misused. The direct results are inefficient classification and overgrinding. The indirect results are added costs through recovery losses, unnecessary recirculation, and so on,

Jan 1, 1985

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

The paper describes a practical methodology based on numerical modelling for the prediction of progressive failure of underground mine stopes with cable bolt support. A case study of the 40-761 stope at Kidd Creek Mine, Timmins, Ontario is presented. The stope was mined by blasthole open stoping in 1986 as a lead stope within a mining block between 36-1 and 38-2 levels. Initially designed to peak at 38-2 level, the stope back caved upwards approximately 40m towards 36-1 level. Cable bolts were installed above the stope from 36-1 level after caving had begun. The stope eventually stopped to cave when the falling rock mass encountered a sufficiently high cable density. The paper provides details of the geomechanical data and modelling results of the case study. Numerical modelling is carried out using a finite element package known as e-z tools which has, among other things, a special cable/rockbolt simulation capability.

Jan 1, 1994

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird's list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997