Search Documents

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

The separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. More than 50 percent of the phosphate reserve in Florida contains too much dolomite to process using current industry practice. The current way of producing phosphoric acid requires less than one percent MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate Research (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option I entails three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand, which could reduce MgO content in the final concentrate by 20 to 40 percent. Option II involves the crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9 percent MgO at about 87 percent P2O5 recovery. Option III is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By Zhiyuan Shen, Dan Zhao

The abstract discusses the importance of reliable mine monitoring systems for preventing accidents. It focuses on diagnosing ventilation system failures caused by roadway faults that alter airflow resistance. The paper proposes using an improved Support Vector Machine (SVM) method to identify the fault location based on changes in air volume detected by wind speed sensors. The approach involves building a sensitivity 0-1 matrix and establishing a roadway fault scope library. The improved SVM method is tested on the Daming coal mine, demonstrating its effectiveness in diagnosing fault locations, reducing training time, and improving accuracy compared to traditional SVM.

Apr 5, 2022

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By W. G. Cornwall

The mining field, inclusive of the treatment plant is located in the foothills, five miles inland from the northern coast of Viti Levu, the largest and most important island of the Fiji Group. Gold and silver occur as tellurides, associated with the sulphides, and as minor occurrences of electrum.

Jan 1, 1975

By Richard Klimpel

The laboratory ball mill grinding of coal/water slurries is described for three coals. Emphasis is placed on the measurement of specific rates of breakage for various operating conditions. Corresponding rheological information is also presented based on data collected using a rotational viscometer. A rheological explanation of the influence of various slurry fluidity conditions on the specific rates of breakage is presented. This rheological approach has proved useful In both the identification of suitable chemicals for increasing breakage rates in coal/mineral slurry grinding and in the plant scale implementation of dense slurry grinding systems.

Jan 1, 1982

By J. B. Hiskey

The principle oxide minerals of molybdenum are wulfenite (PbMoO4), ferrimolybdite (Fe2(MOO 4)3.nH2O), powellite (CaMoO4), and ilsemannite (Mo304). Wulfenite is found in Arizona, New Mexico, Nevada, Utah, California, and Montana. It is also found in the states of Sonora and Chihuahua, Mexico. Prior to 1915 wulfenite ores were the primary source of molybdenum. The solubility of wulfenite in hot sodium sulfide was first noted by Bonardi(1) during attempts to sulfidize wulfenite material prior to flotation. He identified lead sulfide and soluble sodium molybdate as reaction products. Bacon (2) sulfidized wulfenite in preparation for flotation and by X-ray analysis found the reaction product to be lead sulfide. Holmes(3) made an extensive investigation of the extraction of molybdenum from wulfenite concentrates by leaching. Nearly 100% molybdenum extraction was possible from -100 mesh samples leached for 15 min with 10% sodium sulfide solution at room temperature. Molybdenum extraction from -100 mesh samples after leaching 30 min at a temperature of 45°C using 2, 4, and 6% sodium sulfide was about 32, 79, and 98% respectively. The extraction showed little sensitivity to time, temperature, or particle size using 10" sodium sulfide solution.

Jan 1, 1976

By Donald I. Bleiwas

The U.S. Bureau of nines evaluated the potential availability of tungsten from 57 tungsten mines and deposits in 19 market economy countries (1). The 38 properties that were producing at the time this study was performed contain approximately 375,000 tons1 of W03 (tungsten trioxide). The total estimated recoverable resource from all properties studied, both producers and nonproducers, was 1.2 million tons W03 (demonstrated level). Approximately 143,000 tons of W03 is recoverable from producing properties with costs at or below the January 1983 market prices. The study indicates that by 1990 production from currently operating mines in market economy countries will decrease as their demonstrated resources become exhausted. Some of this potential decline may be offset by lower than anticipated levels of market demand, discoveries of additional resources at producing mines, development of other known deposits, and/or discoveries of new deposits. Development of new tungsten resources in market economy countries will likely result in costs higher than exist at currently producing properties. The People's Republic of China has been steadily increasing production and export of tungsten in various form and currently supplies about 25 pct of U.S. imports. China's tungsten mines are large, high-grade operations capable of producing at relatively low cost. These factors, coupled with China's apparent need for foreign exchange, could lead to further expansions of production and exports from China, with a consequent increased dependence by market economy countries on China for tungsten requirements and a threat to the survival of the market economy countries' tungsten industries.

Jan 1, 1984