Search Documents

By Omar Abd el Fattah Ramly, Abdallah Mohamed Sourour

FOREWORD In 1974, the Ministry of Housing and Reconstruction (The Client) which subsequently became the Ministry of Development and New Communities of the Government of the Arab Republic of Egypt assigned responsibility to the Arab Contractors (Osman Ahmed Osman and Company) for the design and construction of the tunnels under the Suez Canal. For this project the Arab Contractors of Cairo and Tarmac International of London formed a joint Venture, called Osmac. Sir William Halcrow and Partners of London are responsible for the design of the Ahmed Hamdi Tunnel as a Sub-Contractor to the Contractor. The advisory consultant of the client is a joint Venture between Tippetts-Abbett-McCarthy-Stratton (TAMS) of New York and Arab Consulting Engineers (ACE) of Cairo. INTRODUCTION A site investigation was carried out between Km 141 and Km 150 Suez Canal chainage to determine the ground conditions relevant to design and construction of a road tunnel under the Suez Canal. A feasibility study included aerial surveying, geological mapping and the drilling of 8 boreholes. Detailed investigation included the drilling of 105 boreholes, sampling, piezometer installation, pumping tests, and the digging of trial pits and trial excavations. In-situ work comprised SPT, permeability tests and dilatometer tests. Laboratory testing included soil classification tests, compaction tests, California Bearing Ratio tests, shear strength determination and oedometer consolidation tests as well as chemical analysis of both soil and ground water. The investigation revealed that the ground conditions at the first proposed El Shatt site (Km 148.5) were not favourable for bored tunnelling, whereas they were more favourable at the southern El Shatt site (Km 150.0).

Jan 1, 1979

By J. L. Sloughfy

The size distribution and mechanical strength of the iron ore pellet burden are important parameters in determining the efficiency of the blast furnace. From the very outset, the guiding principle of our pellet quality improvement program was that these parameters are also the key to improving productivity and cost control at the pellet plant. Recognizing the need for improved blast furnace burdens and for higher productivity and lower costs at the pellet plant, Carol Lake operators, in conjunction with the IOC Pellet Quality Committee, established the following goals for the improvement of Carol pellets: [ ]

Jan 1, 1981

By R. J. Miller

Rock strata, natural and mining-induced stresses, and structural features can combine to create dangerous instabilities in or around longwall panels. Rock noises and properties variations associated with local stress systems can be used to characterize developing instabilities. Through a learning process at a particular mine, guidelines can be developed to allow the determination of relative risk and timing of a potentially disastrous instability. Once a dangerous instability has been identified, operational modifications can be employed to get through the instability, or active measures such as destressing can be used to mitigate the instability. This paper will discuss how an integrated monitoring system and associated data processing can be used to develop a hazard prediction capability for a longwall mine.

Jan 1, 1996

By D. Scott Barr

The Zarafshan/Newmont Joint Venture operates the Muruntau heap leach project, located in the Kyzylkum desert of central Uzbekistan. The mine produces more than 12.4 t/a (400,000 oz/year) of gold from low-grade oxide ore stockpiles adjacent to the Muruntau open pit. It is op¬erated by the Navoi Mining and Metallurgical Combine and is one of the largest gold resources known (Fig. 1). Since commissioning in 1995, total heap leach production has exceeded 21 t (675,000 oz). The joint venture uses four-stage crushing and screening to produce a final product for heap leaching, Merrill-Crowe processing and local refining.

Jan 1, 1998

By J. J. Casey

This paper is one of a series of presentations organized by the Conference of American Society of Civil Engineers with the goal of making significant progress toward an equitable and effective allocation of risks in construction undertakings among the principal parties - owner, contractor and designer. The role I have been assigned is principally one of identification of risk while others will devote greater attention to the allocation of these risks and the contractual arrangements necessary to properly make these allocations. Construction projects are joint undertakings by parties who bring different skills and interests toward a common effort, much as this conference does. A project is not an adversary proceeding and does not benefit from establishment of an adversary mode, as our lawyer friends seek in the resolution of legal issues. Accordingly, I urge upon this Conference the adoption of two basic precepts and guidelines as the criteria for sharing of the risks inherent in construction undertakings toward achievement through mutual effort the common goal of a successful project completed in the shortest time and at the least overall cost. These precepts are: (1) that all risks are rightfully the owners unless transferred to or assumed by another party for a fair compensation; and (2) that the principle guideline in determining whether a risk should be so transferred should be whether the receiving party has both the competence to fairly assess the risk and the expertise necessary to control or minimize it. The sponsors of the conference have provided certain guidelines to the authors. There is, however, no constraint in expressing one's bias and I suspect that my contractor's outlook may be inherent in my comments. The guidelines have suggested that I indicate whether the risks identified are ones that can or should be shared or borne by one party alone. In doing so, I will attempt to follow the precepts I have recommended.

Jan 1, 1979

By David R. Delling

Tenneco is a large, diversified, energy-based company which has grown rapidly during its forty year life. We're the youngest corporation among Fortune's top 20 companies. Tenneco Minerals Company is the division of the Corporation responsible for nonfuel minerals exploration, development and operations. Tenneco Minerals Company is headquartered in Lakewood, Colorado. Exploration offices are in Colorado, Nevada, Alaska, and Perth, Australia. We currently operate two gold mines in Nevada and a large underground trona mine and soda ash processing plant in Wyoming. The latter has a capacity of 907 000 tonnes per year of soda ash and is the subject of my presentation today.

Jan 1, 1984

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By Jim McKinley

With a growing number of mines reaching closure and seeing closure costs materialize, regulators, lenders, and banks are observing projects that fail economically by miscalculating these costs. Mine closure costs are often categorized as a type of liability which is defined as the money owed by the company to offset effects from the project, and the money available to pay for those debts (e.g., bond). Often, decisions made before Day 1 of mining (e.g., co-disposal, dry stack tailings, waste segregation) can significantly change the bond calculation. Once the bond is calculated and funded, operators are encouraged to conduct closure research and use applied science for progressive bond release prior to final closure. However, this author has observed few instances of financially significant progressive bond release, as there are typically no robust procedures for bond return, either before or during closure activities. As a result, many companies decide that entering a state of Care & Maintenance (C&M) is less risky than attempting to fund closure activities with an unknown bond return mechanism. Although perhaps less risky in the short-term, the primary long-term risk with entering C&M is that it increases the chances of the bond not covering the cost of closure and the chances of the government/regulatory agency inheriting the mine closure. Bonds are typically reevaluated on a regular cycle (e.g., five years) so every mining company goes through this financing challenge eventually.

Feb 22, 2026

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By Frank J. Skudrzyk, Vladimir F. Petrov

In compliance with the current Russian environmental legis­lation, possible impact of industrial activities on the environment is restricted by acceptable limiting values (maximal allowable concentrations - MAC) of individual chemical substances in the natural environment - water, atmospheric air and soils. These norms have federal status and are valid for the whole territory of Russia. Disposal of the substances, for which no MAC is estab­lished, is forbidden by the law. Many gold mining companies use cyanide in precious metal recovery. This paper overviews the Russian experience in pro­tection of natural water reservoirs from technogenic impact of cyanic technologies. Major toxic compounds, contained in liquid and solid rejects from hydrometallurgical treatment of gold ore using cyanidation, are cyanides (CN), thiocyanates (SCN) and cyanide metal com­plexes. Unlike western classification of various cyanide types, in Russia any inorganic cyanide compounds (simple and in com­plexes with metals), with the exception of iron cyanide com­plexes, are considered toxic and the acceptable limiting value is established for them. MAC is 0.05 mg/I for fish reservoirs and 0.1 mg/I for drinking water. For iron cyanide complexes MAC is 0.15 mg/I for fish reservoirs and 0.25 mg/I for drinking water. Russian norms for thiocyanates are practically as rigid - the acceptable limiting value for them in fish reservoirs is at the level of 0.07mg/l (0.15 mg/I for potassium thiocyanate) and for drinking water - O. lmg/1. Norms for metals are established on the basis of total content regardless of the form in which they are present in water - as cations or complex ions. It should be noted, that in case several toxic compounds of the same limiting value (for cyanides, thiocyanates and base metals the limiting value is toxicological) are present in water. Their allowable concentra­tion is calculated as the sum of actual concentration of each com­pound, divided by the corresponding acceptable limiting value, with the result not to exceed one (compounding effect). Differences in cyanide classification and the necessity to include thiocyanates dictate different analytical methods. This, in a number of cases, results in certain discrepancies in analytical results. Until recently chlorination was used as a basic process of detox­ification of wastewaters. Calcium hypochlorite powder or hypochlorite pulp, prepared of lime milk and chlorine shipped to the plant, were used as a reagent. Chlorination is an efficient method: it allows to completely destroy plain and complex cyanide, in addition to iron complexes, and thiocyanates. A good example of high efficiency chlorination can be found at the Mnogovershinniy mill near the Okhotsk Sea located in the salmon spawning area, for which we designed an automated chlorination plant for tailings dam. Since plant start-up ten years ago, the required concentrations of cyanides and thiocyanates have been kept at the MAC level required by environmental regulatory agen­cies and no harmful affects on ichthyofauna has been reported. One major drawback of chlorination is high cost of the major reagent, as well as secondary contamination of detoxified waters by chlorides. Secondary contamination by chlorides becomes obvious in the course of detoxification of wastewaters of com­plex composition, which require increased reagent consumption. Recent changes in economic conditions in Russia caused the necessity to direct efforts to reduce the costs of precious metals recovery, and in particular, wastewater treatment. We have con­ducted certain work in this direction and obtained positive results. We hope that our experience described below will be of interest to other specialists particularly taking into account the current low gold prices.

Jan 1, 1998

By W. J. Spat

Political risk is an integral part of the mining business in Northern Andean countries. Peru, Ecuador, Colombia, and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations in such contexts require: 1. Good political risk information; 2. A thoroughgoing political risk management plan; and 3. A strategy to deal with political risk perception on the part of the investing public. Obtaining quality political risk information, developing a political risk management plan, and addressing political risk perception are the foci of this work.

Jan 1, 1999

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By W. N. Hamilton

British Columbia is geologically favourable for a rich variety of industrial mineral occurrences. Some have been produced for years, others overlooked until recently. Major production occurs for asbestos, gypsum, limestone, magnesite, silica and sulfur; lesser production for a dozen others. For several of the minerals, potential is much greater than existing production. New production opportunities exist also for diamonds, niobium and REE minerals, fluorspar, kyanite, nepheline syenite, talc, and several others. Alberta, though geologically less diverse, also has many industrial minerals. Limestone, salt and sulfur have the major production; clay and shale, silica, sodium sulfate and a few others lesser production. Opportunities exist for expanded production, and for new production in heavy (Ti -Zr) minerals, formation brines (Ca-Mg-I-Li), and gypsum.

Jan 1, 1987

By L. Max Scott

[INTRODUCTION] The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U308. Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U308. The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure. [Dose Estimates] When one has a point source of radiation, the conventional laws of isotropic emission and the fall of dose with square of the distance, make dose calculations relatively easy. However, if one has an area source of infinite thickness, the assumption must be made that a uniform gamma flux is being emitted from all faces of the source (Figure 1). Dose from gamma emission would fall off only due to air attenuation up to such a distance at which the source can be considered to be a point source (usually 10 times the largest dimension of the source). For short distances, such as to the cab of ore-moving equipment, the dose reduction would be negligible. Assumptions: 1) Radium and gamma-emitting daughters are in secular equilibrium with uranium. 2) All gamma radiation is emitted from radium and its daughters. 3) Average gamma energy of 0.8 MeV. 4) Uranium ore has a linear attenuation coefficient of 0.212 cm-1, similar to that of Si02(sand). 5) Uranium ore density of 3.0 gm/cm3. 6) One curie of radium emits 6.84 x 1010 photon/sec(l). 7) One percent uranium ore contains 1 x 10-8 Ci/cm3 of radium. 8) Each MeV of 0.8 MeV photon results in a dose of 2.10[ ]10-3 mRem/hr. per MeV/cm2 -sec. 1) 9) Minimum ore depth 100 cm. 10) Linear attenuation coefficient instant for radium gamma of 0.374 cm -1 [ ] The photon flux from a radioactive slab is computed as follows: [Flux = photon/cm3 3(1) 2u S] [where, us is the linear absorption coefficient of s the source (uranium ore).] Thus, 1% uranium ore, in the form of an infinite slab, emits 1613 photon/cm2-sec, which results in a dose rate of 2.71 mRem/hr. Since the dose from an infinite slab is the same as a dose from an infinite radius right circular cylinder, the only correction needed from the above dose rate is for finite radius and point of dose above the end of the cylinder (Figure 2) [Dose = mRem/hr. {E2(bl) - E2(b3) - [(E2(b1sec[E] -E2(b3sec[E]]cos[O](1)]

Jan 1, 1981

By Stephen Liu

Tunnel excavation while mining is not often performed in North America primarily due to access constraints in both operations. Referencing European approaches for long distance tunneling, the Devil?s Slide Tunnel project has applied innovation and technology to provide the ability to overcome this unique challenge. The Devil?s Slide Tunnel requires the construction of twin bore tunnels excavated based on sequential excavation method (SEM) construction methods using New Austrian Tunneling Methods (NATM) principles. The twin tunnels are approximately 9 m (30 ft) in diameter and 1,250 m (4,100 linear ft) in length. The purpose of this project is to reroute Route 1 from around the Devil?s Slide through the San Pedro Mountains crossing from Montara, CA along the south and into Pacifica, CA in the north. The Caltrans project was awarded in December 2006 for a total of $272,366,000. The job is an A+B job, thus the estimate scheme of final lining while tunnel excavation is important to save time. A+B is a method of rewarding a contractor for completing a project as quickly as possible. By providing a cost each working day, the contract combines the cost to perform the work (A) with the cost of impact to the public (B) to provide the lowest cost to the public. Concurrent mining while lining is achieved through a series of gantries and a set of tunnel forms allowing the pass-through of the excavation equipment. The tunnel lining operation passes through several phases of work that are dependent upon the progress of the tunnel excavation process. This involves unique milestones, such as the evolution of the ventilation system, development of an enlarged cross passage to allow equipment to access each tunnel from within the tunnel and, finally, the installation of an invert prior to arch lining that limits the continuity of the final lining operation.

Jan 1, 2011

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019