Search Documents

By W. D. Eddy

Topaz is a fluorine-bearing aluminosilicate mineral of the kyanite-sillimanite group. The formula has been given as Al2SiO4(F,OH)2, [Al(F, OH)]2SiO4, or 2Al2O3?2Al(F, OH)3SiO2. Topaz is generally considered a semiprecious-to-precious gem mineral, but it is a fairly common minor constituent of granites. In 1937 the U.s. Geological Survey reported an occurrence of massive topaz in the 3 Brewer gold mine, Chesterfield County, S.C. Over the next 8 years considerable research was done on topaz to establish its properties and to determine possible end uses The first reported shipment of ore was in 1939 Peak production was reached in 194412, and output then began declining until the mine closed in 194913? During World War II topaz was used in refractories, as a flux in steel mills, and in the manufacture of borosilicate glass 14. The main advantage of using topaz over kyanite and sillimanite in refractory use was that calcined topaz converted to over 95 percent mullite (3A1203 .2Si02) while calcined kyanite or sillimanite contained only 88 percent mullite15. However, a major draw-back to utilization of topaz is the evolution of fluorides during calcination. In 1973 the Geological Survey reported that topaz occurred in probable commercial quantities in at least two domestic locationsl6: the Brewer area of South Carolina and a location in Colorado. The literature also indicated that progress had been made in controlling fluorine-bearing fumes. This research has progressed to the state where valuable fluorine compounds are being recovered on a commercial scale 17. Thus, a major obstacle to utilization of topaz appears to have been resolved. The Bureau of Mines under its program of advancing minerals technology initiated a project to study techniques for the concentration of topaz from disseminated materials. The objective of the study was to determine those techniques that would be used to produce topaz concentrates that could be utilized as a source of fluorine and mullite.

Jan 1, 1977

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By Gary N. Weinrich

Large surface mining projects in sparsely populated regions of the West have the potential to create disruptions in an area's social and economic character with potential effects on man that can far outweigh the physical and ecological effects on man's environment. The data and analyses involved in addressing the socioeconomic issues are additional to those traditionally associated with surface coal mining, such as those concerning land reclamation and water quality. Appropriate socioeconomic studies in conjunction with mine-planning can identify the potential problem areas in order that project measures can be taken to maximize the beneficial impacts and minimize the adverse effects of surface coal mining. The information required to conduct such socioeconomic analyses, available data sources, and the applicable analyses are described. Overall impacts of some proposed Western surface mines are summarized and potential mitigating steps discussed.

Jan 1, 1975

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

By L. Martin, M. Raffaldi, M. Stepan, D. Benton

The Office of Mine Safety and Health Research, Spokane Mining Research Division, is continuing its high-energy, high-displacement testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link mesh, welded-wire mesh and combinations of them. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can assist in interpreting the condition of installed surface support. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to better quantify the stability of installed shotcrete support.

Jan 1, 2016

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By Maryam Motamed, Jeremy Stone, Leigh Anne Zhang

Controlling and predicting ground movements are essential to the design of shoring systems. The Courthouse Commons tunnel in San Diego, California, included a 56-foot-deep temporary shaft as a launching point for tunneling using the Sequential Excavation Method (SEM). The rectangular shaft was unique in that it was surcharged on one wall by an 11-story building and employed a hybrid support of excavation design. An array of geotechnical instrumentation was used to monitor lateral and vertical movements at the ground surface. This paper compares the measured ground movement with the predicted ground movement from various excavation stages

Dec 1, 2022

By Jim Huerta

Diesel fuel usage in the mining industry continues to escalate. This is because approximately 60 percent of all mined materials are surface extracted by large equipment using diesel fuel, which continues to increase in cost per gallon. For example, coal mining uses large equipment such as wheel loaders, wheel dozers, draglines and [ ] dredgers. In one year, three of the largest U.S. coal mining operations consumed approximately 567 million to 852 million L (150 million to 225 million gal) of diesel. At an approximate cost average of $3.25/gal the expenditure on diesel is $487 million to $731 million per year. So, are there any solutions that could reduce this cost burden? Yes, there are. Coal mining companies can extract less ore; use more efficient extracting equipment that consumes less fuel; wait for a significant reduction in the cost of fuel; or find and use technology that would create efficiencies that would lower the cost. Nanotechnology is one such technology that might provide the means to create the efficiencies that will significantly lower diesel fuel costs.

Jan 1, 2011

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

Roadheaders are commonly used in coal mines for roadway excavations. The prediction of roadheader performance is necessary for the planning of roadway projects and the estimation of costs. Recently, a new rock mass cuttability classification (RMCC) system has been introduced for roadheaders used in coal mines. In this study, the validity of the RMCC system was investigated for different types of roadheaders and different coal mines. Four different coal mines were visited, and the performance measurements of different axial and transverse roadheaders were carried out during the excavation of roadways. Uniaxial compressive strength, volumetric joint count, the strike and dip of joints, joint aperture, the Cerchar abrasivity index, and water ingress were determined in field and laboratory studies to calculate the RMCC index. The analysis of the data demonstrated that the correlation coefficients between the net cutting rates and the RMCC indices were higher than 0.94, suggesting that the RMCC system was valid. It was concluded that the RMCC system could be reliably used for the evaluation of roadheader performance in coal mines.

Jun 21, 2023

By M. Paul

"INTRODUCTION In 1990, the uranium production of SDAG Wismut in East Germany was stopped. 45 years of inconsiderate destructive exploitation had scarred both landscape and nature. With the “Wismut law” which came into force in December 1991, the Federal Republic took responsibility of the remediation of the legacies from former uranium ore mining and milling in Saxony and Thuringia. A unique opportunity turned out in order to remove environmental damage, to enhance the life quality of the local population, to shape new landscapes and to advance the economic restart. (1) The results of nearly 25 years of remediation activity are evidence that this opportunity was used at all former SDAG (Sowjetisch-Deutsche Aktien-gesellschaft) Wismut sites. The reference project “Wismut“ has evolved into a joint project of all parties involved and radiates beyond the affected regions. This is particularly reflected by the Know-how transfer starting from Wismut and the increasing activities for third parties abroad.WATER MANAGEMENT AT WISMUT REHABILITATION Within the Wismut project, water management and conventional technical water treatment are by far the most cost-intensive long-term tasks of the remediation programme. Over the medium term, there is no viable alternative to the operation of active systems to catch and treat contaminated mine waters at the Ronneburg, Schlema, Königstein, Pöhla, Seelingstädt and Helmsdorf sites. Based on the status quo, this paper outlines the key issues of the Wismut GmbH water management strategy over the medium and long term. It is focused primarily on achieving protection goals for potentially impacted water bodies in the surroundings of Wismut sites and on optimising associated remediation expenditures as well as on creating the prerequisites for achieving low post-remedial care and maintenance or walk-away system status over the long term. (2) The applied mining practices during the active SDAG Wismut period have not been up to the high standards of modern mining operations and their requirement to leave former production premises and deposited residues in a condition that was not only physically but also chemically stable. Rather the emission of mine and seepage waters laden with high acidity, metal and salt content is a frequent corollary and difficult legacy of historic mining and processing operations (4, 5). As a consequence, the control or mitigation, respectively, of environmental impacts associated with contaminated mine waters ties up enormous public resources worldwide (6, 7)."

Jan 1, 2016

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By Anuradha Khetwal, Tala Tahernia

The estimation of TBM utilization rate can be problematic due to the uncertainty involved in the tunneling system reaction to various geology along the tunnel. Moreover, the impact of operational and management issues on TBM performance is unsettled. This includes the occurrence and duration of downtimes and the uniqueness of projects relative to the geology, machine type, backup system, site setup, crew experience, and operational restrictions imposed on the project by localities. The CSM2020 is a model based on discrete event simulation that predicts machine utilization for single or double shield TBM. This model was developed by the Earth Mechanics Institute (EMI) team, using the database of tunneling activities which was compiled based on field observation and measurements in pertinent projects. In the current study, CSM2020 was modified to simulate the workflow of slurry TBMs. The operating principle of slurry shield TBMs is different than open-mode TBMs. The model was verified by comparing results with a recently completed project in the United States. As a result, the model offers reliable utilization rate estimation in different types of TBM by implementing appropriate workflow.

Dec 1, 2022

By Richard Klimpel

The influence of selective chemical dispersants on the hydrocycloning of a copper ore slurry is illustrated. In the % solids and slurry feed rate ranges associated with industrial practice, desirable changes in both d50 and Sharpness Index values of classification were measured with the use of chemical as compared to tests with no chemical usage.

Jan 1, 1981

By Rudecindo S. Silo

[The principal characteristics of the process is that when applied in medium or in great degree it only needs unelaborated raw materials such as sodium chloride and calcium carbonate, or of medium elaboration, as sulphur which is found in large quantity in the North of Chili; however, the may be also applied to small copper plants provided that low cost sulphuric acid is available as a substitute for sulphur, that is, in. those plats of small capacity where large additional installations are not needed for the regeneration of the leaching solution. The method itself comprises 6 stages, namely: crushing, leaching, washing; of solutions, precipitation, regeneration of the leaching solution and fusion.]

Jan 1, 1965

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA's BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA's hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014