Search Documents

By M. L. Brashears

Pine Point Mines is located in the Northwest Territories of Canada, about 500 miles north of Edmonton, Alberta (figure 1). Lead-zinc ore is found in numerous localized deposits along a generally east-west trending reef of Devonian dolomite, about 5 miles south of Great Slave Lake. A pumping-test program was carried out in 1968 to guide the design of dewatering systems for several open pits that are partially or wholly below the natural ground-water levels. The hydrogeologic conditions, methods employed and results obtained are discussed.

Jan 1, 1971

By Tracey A. Conrad, Mark E. Mussett, Max Kaufmann

The varied benthic habitats of the Pacific Ocean are comprised of different types of seafloor geology. These geologic domains generally consist of sedimented abyssal hills, high relief features such as seamounts, and polymetallic nodule fields that vary in spatial extent and abundance. Nodules represent a deep ocean habitat type, and are of economic interest owing to their metals content. Multibeam data can be used to classify seafloor geology. The wide swath of hullmounted multibeam systems used in deep water provides efficient coverage of large areas of seafloor. Our research examines how multibeam backscatter and bathymetry data, with regional environmental parameter assessments and GIS analysis, can help identify probable polymetallic nodule fields in the deep remote ocean prior to groundtruth seafloor observations. A workflow for processing 30 kHz hull-mounted multibeam data within QPS Qimera and FMGT software was developed to facilitate multibeam processing, while also generating a terrain model and backscatter products. An additional GIS protocol for evaluating multibeam data products, including cluster analysis, was also developed. These methods were applied to a test case of publicly available multibeam data collected by the Ocean Exploration Trust and NOAA. Processed multibeam products were used to identify areas exhibiting coarse sediment backscatter characterization with low relief; filters for water depth at or below the regional CCD, seafloor age, and sedimentation rate were then applied. Sophisticated GIS cluster analysis further identified trends within the data to forecast where coarse sediment domains, potentially including nodule occurrences, exist. The test case multibeam data allow determination of the composition and variability of seafloor geology. This analysis can further identify where previously unexplored nodule fields may exist and edify estimates of nodule extent throughout the ocean. The research methods and outcomes contribute to marine spatial planning, ecosystems modelling, and mineral resource management initiatives.

Feb 22, 2026

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By Y. C. Kim

Although the first published optimum pit limit design algorithm by Lerchs-Grossmann dates back to 1965, the majority of the open-pit mines in the U.S. has not as yet adopted such a rigorous optimization algorithm. Instead, the floating cone approach initially developed by Kennecott Copper in 1961 is still used today for various reasons. However, shortcomings with the floating cone algorithm, particularly for precious metal deposits with erratic mineral distributions, have provided a renewed interest in optimizing algorithms.

Jan 1, 1988

By C. L. Karr

Researchers at the University of Alabama are investigating artificial intelligence based computer models of mineral processing systems. Two approaches have been found to be particularly effective in developing data-driven computer models. The first approach employs neural networks which are computational paradigms based on the mechanics of the human brain. They are able to extract the basic relationships between input and output variables from large data sets. The second approach combines fuzzy mathematics with genetic algorithms to produce an adaptive modeling system. Fuzzy mathematics provide computers with the capability of manipulating abstract concepts like those which humans use so effectively in decision making. Genetic algorithms are search algorithms that mimic evolutionary processes apparent in nature. Together, these two techniques can be used to produce an effective modeling system. In this paper, the two approaches to modeling are compared and contrasted with respect to accuracy and computational time while used to model three mineral processing systems: (1) a grinding circuit, (2) a hydrocyclone separator, and (3) a flotation circuit.

Jan 1, 1997

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines' airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By A. D. Trippel

The Cripple Creek Mining district is located in Teller County, Colorado, 30 km west of Colorado Springs and 9 km southwest of Pikes Peak (Fig. 1). Since its discovery in 1891, the district has produced almost 21 million tr oz of gold (Gott et al., 1967), most of which has been from high-grade vein deposits. Globe Hill is located in the northern part of the district (Fig. 2). Production from its summit has yielded over 100,000 tr oz of gold. Early production was concentrated along high-grade veins and fault structures, but emphasis was soon placed on the extensive, low-grade (0.0X oz/t), breccia-hosted mineralization. From 1977 to 1981 Newport Minerals, Inc., a subsidiary of Gold Resources, Inc., mined 680,000 t of low-grade gold ore from the Globe Hill pit (Fig. 3) and production is expected to resume in 1986. These strongly-altered and -oxidized breccias are amenable to bulk-mining methods, and thus similar deposits are currently being sought elsewhere in the district. Numerous publications and reports discuss the breccia-hosted mineralization at Globe Hill. They include Cross and Penrose (1895); Argall (1905, 1908); Lindgren and Ransome (1906); Keener (1962); Peters (1982); Thompson, Trippel, and Dwelley (1985); and Trippel (1985). This preprint is a summary of the recently-completed research documented by Trippel (1985).

Jan 1, 1986

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by more than 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy.

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984