Search Documents

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T '1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By J. A. Ober

"In 2016, the estimated value of total nonfuel mineral production in the United States was $74.6 billion, a slight increase from the revised total of $73.4 billion in 2015 (Table 1). Increased construction activity spurred increased production of industrial minerals, especially those used in infrastructure and residential construction. Although starting the year relatively low, prices for several metals, especially for some of the precious metals, began to trend upward. Decreased production of most metals produced in the United States, however, contributed to an overall decline in the value of metal production.Several U.S. metal mines and processing facilities were idled or closed permanently in 2016, including iron ore mines in Michigan and Minnesota; three primary aluminum smelters in Indiana, Missouri and Washington; one secondary zinc smelter in North Carolina; a titanium sponge facility in Utah and titanium mineral operations in Virginia. In addition, in May, the weekly average rig count for oil and gas drilling reached its lowest level since the 1940s when that measurement was first recorded. The reduced drilling activity resulted in decreased production of some industrial mineral products used in the drilling sector. Trends in mineral-related sectors of the domestic economy declined or held steady, except in the manufacturing of nonmetallic mineral products and nonferrous metals excluding aluminum, which increased. Overall, mining trended downward as the result of significant declines in coal mining, oil and gas extraction and metal mining (Table 2). Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct compar"

Jan 5, 2017

By U. S. Geological Survey Staff

"In 2017, the total estimated value of nonfuel mineral production in the United States increased by 6 percent from 2016 (Table 1). The value of metals produced domestically increased by 12 percent and the value of industrial minerals produced domestically increased by 3 percent. Some metal commodity values (cobalt, magnesium metal and palladium) increased by more than 35 percent in 2017 from 2016 owing to higher prices.Some U.S. metal mines and processing facilities remained idle in 2017, including three primary aluminum smelters in Indiana, Missouri and Washington; a titanium sponge facility in Utah and a byproduct vanadium production facility in Utah. In contrast, new gold mines opened in late 2016 and 2017 in Nevada and South Carolina, respectively, and iron ore mines in Michigan and Minnesota restarted or operated for the full year. In addition, increased oil and natural gas drilling activity led to increased production of some industrial mineral commodities that are used for oil and gas drilling. Production of some industrial minerals, especially those used in infrastructure and residential construction, remained essentially unchanged in 2017, a reflection of the limited growth in construction activity. The production of some metals, including iron and steel, aluminum and other nonferrous metals and nonmetallic mineral products increased. Overall, mining activity trended upward as the result of increases in coal mining, oil and gas extraction and metal mining (Table 2).Discussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

Jan 5, 2018

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By Dion Weatherley, Raúl Castro, RENE GOMEZ, Pablo Cid

The study examines the impact of different drawbell geometries on hang-ups during ore extraction in underground mining. Using the discrete element method, the research compares three drawbell geometries: drawer, circular, and El Teniente. The findings indicate that the El Teniente geometry experienced more hang-up events, while the circular geometry had fewer.

Sep 1, 2023

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

The health and safety of miners is critical in the industry. Prolonged exposure to dust-laden air results in irreversible ailments like pneumoconiosis that have a severe impact on their lives. Operations use various personal protective devices (PPEs) to alleviate their exposure to respirable dust. Powered Air Purifying Respirator (PAPR) is one such device that uses high- efficiency filters and positive pressure masks to shield miners from airborne contaminants. Used in the medical and other industries, these respirators efficiently protected healthcare workers during the COVID-19 pandemic. Recently, the mining industry has shown a growing interest in adopting this PPE to ensure safe working conditions for the miners. We present an introduction to the PAPRs and discuss their dust capture efficacy in this manuscript.

Feb 1, 2025

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By K. Awuah-Offei, A. U. Rehman

"Information diffusion potential of a social media user affects how quickly information about a mineral project can diffuse through that user. If management can use social media and network analysis, in community engagement program, to understand how fast and how far information will diffuse to communities and followers of particular social media users, it can selectively focus on the most influential users. This paper proposes a method to examine the information diffusion potential of social media accounts. The work uses Gephi, an open source software, to extract and analyze data from different Twitter handles to predict their information diffusion potential. The work uses case studies of real Twitter users (e.g. mining news organizations and bloggers) associated with mining to illustrate the approach. The case study results show that there are significant disparities in information diffusion potential that will demand selective attention. This research will help mines develop effective social media engagement strategies. INTRODUCTION The mineral industry provides raw material for industrial activity to support our society (Martens and Rattmann, 2001). Mines have changed conventional mining practices to sustainable ones because of the negative impacts of mining and increased public awareness (Wang et al 2016). The concept of sustainable mining is getting mature as stakeholders (e.g., governments, investors and host communities) are getting involved in mining projects (World Economic Forum, 2014). The failure of mining companies to address the demands of these stakeholders might result in failure to acquire social license to operate (Thomson and Boutilier, 2011). The social license to operate (SLO), if granted, is mutually beneficial to all stakeholders. Mines prefer being granted SLO and keeping it to avoid any kind of social unrest due to their operation (Prno, 2013; Moffat and Zhang, 2014). Mining communities can grant different levels of SLO; ranging from withholding SLO to psychologically identifying with the project (Joyce and Thomson, 2000; Thomsan and Boutilier, 2011). Most of the previous work to understand community perceptions and SLO in mining is generally qualitative (ICMM, 2012a; Thomson and Boutilier, 2011; Prno, 2013; Moffat and Zhang, 2014; IFC, 2014). In particular, there is limited work on how community perceptions change over time due to information diffusion (Boateng and Awuah-Offei, 2017). However, SLO changes with respect to time (Yates and Horvath, 2013), which can result in risks that are not easy to predict. Mine managers and engineers have a desire to understand these changes so as to mitigate these risks (Que and Awuah-Offei, 2014; Que et al., 2015)."

Jan 1, 2018

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Robert G. McLusky

Since 1998, environmental extremists have waged war with the central Appalachian coal industry in West Virginia and Kentucky. In particular, they have filed three lawsuits challenging the legality of excess spoil ‘valley fills’ under CWA, NEPA and SMCRA: 1) Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D.W.Va. 1999), rev’d. 248 F.3d 275 (4th Cir. 2001); 2) Kentuckians for the Commonwealth v. Rivenburgh, 204 F.Supp. 2d 927 and 206 F. Supp. 2d 782 (S.D.W.Va. 2002), rev’d. 317 F.3d 425 (4th Cir. 2003); and 3) OVEC v. Bulen, 2004 U.S. Dist. LEXIS 12690, July 8, 2004; OVEC v. Bulen, 2004 U.S. Dist. LEXIS 16078, August 13, 2004.

Jan 1, 2005

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By Richard C. Mayberry

Phosphate reserves have been and still are a controversial subject. Some published estimates are particularly conservative and have caused concern in government and political circles that southeastern phosphates are a dwindling resource. "Ores and ore bodies" are a function of economics that relate to a time/demand factor. The history of phosphates and other mineral commodities is one of mineral deposits (resources) ever becoming ore (reserves) via a long term logic based on price, supply, and demand factors operating through time and improved technology. Projections indicate that southeastern phosphates are sufficient for several centuries of operations at present production rates.

Jan 1, 1981