Search Documents

By J. A. M. Cano

Pot Grate tests were carried out in the pilot plant at Samarco producing pellets containing SiO2 between 2.0% and 2.2% in a wide range of basicity to be used in blast furnace. These pellets were submitted to tests in Samarco's laboratory and another laboratory in Germany to evaluate the metallurgical properties. The pellets in the binary basicity range (CaO/SiO2) from 0,87 to 0,95 were those that presented the best results in the Pot Grate tests. Based on the results, these pellets are being routinely produced?on industrial-scale confirming the results observed in laboratory tests.?

Jan 1, 1994

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By Kwame Awuah-Ofei, Sisi Que, Shaochun Yuan, Yumin Wang, Ziwei Ding

This research sought to facilitate improved stakeholder analysis in mining by providing further insights into the preferences of local community members using discrete choice theory. While recent research has demonstrated the usefulness of discrete choice theory in mining stakeholder analysis, no previous work has examined which discrete choice model (DCM) is most suitable. This paper provides a research note on a case study in a mining community that was performed to compare three DCMs. After a thorough examination of the benefits and deficiencies of all models, this study concludes that the conditional logit model stratified by questions is the most useful DCM for mining stakeholder analysis. The recommendation is based on the usefulness and accuracy (ability to match the survey data) of this model.

Jul 25, 2022

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By A. J. Basu

An overview of the evolution of computerized mine planning and design has been given, emphasizing the need for a knowledge-based system for planning and design of underground coal mines. An outline for the development methodology and procedure has been provided. Problem structuring guidelines have been used to incorporate intelligence and integration to the design modules. A skeletal model for a mine planning and design expert system has been prescribed, and the development process has been documented in detail. A feasibility prototype has been developed to test the structure of the skeletal model and to ensure completeness of the design process. The feasibility prototype development and its contribution toward proto typing has been addressed in this paper. At present, prototype development is underway. The prototype is expected to be avail-able for testing and implementation in early 1991.

Jan 1, 1991

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2010 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2010: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2010, as compiled by the USGS, and 3) regional events including economic, social and political conditions that affected exploration activities. These were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2011

By J. Drelich

The flotation limit of fine particles has been re-examined based on the effect of bubble size on contact angle, and a new surface chemistry-limited relationship describing the minimum particle size which can be floated is proposed. In this analysis the critical value of bubble-solid contact radius (re) for which there is no effective attachment between particle and bubble has to be determined. The values of re determined by extrapolation of our experimental data for contact angle versus bubble-solid contact diameter permit the prediction of the flotation limit of methylated quartz particles, with fraction-al coverage of trimethylsilyl groups from 0.07 to 0.51. The limit of fine particle flotation as determined by this theoretical approach agrees well with experimental data reported in the literature.

Jan 1, 1994

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

By Smart Chika Obiora, Anthony Chukwu

Mining and processing of raw materials is one of the earliest activities of man for survival and development. The products are used for making jewelleries, metal tools, and for exchange of goods and services. However, despite the benefits of mine recoveries, it’s negative and long term effects on the environment and lives remain the point of discussion throughout the world. This study summarizes findings of researches in active/abandoned lead–zinc mines in Enyigba and Ishiagu mining districts including social surveys in the localities surrounding the mines in order to ascertain the effects on the inhabitants. Lead–zinc mining in Enyigba and Ishiagu, southeastern Nigeria has lasted for decades and has affected the socio-economic well-being of the host communities. There are evidences of soil, water, and plants contamination by Pb, Zn, Cd, and Mn in these mining communities. The mining activities also affect the overall social development of the host communities. These effects include retardation in educational development, health care provision, unemployment, and access to potable water supply. Others are rise in poverty level, social amenities, sanitary/hygiene level, high cost of living, and fertility rate. Possible mitigation strategies such as to liaising with relevant government agencies in collaboration with mine owner, mine workers, and host communities can ameliorate these negative effects and promote environmental sustainability.

Feb 24, 2023

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By Joel L. Morrison

The preparation of coal-water slurry fuel (CWSF) has the potential to be a commercially viable technology for the coal industry. The technology base required to prepare stable CWSF using grinding circuits has been developed over the past decade and is now being applied to the preparation of CWSF from wet coal fines which are generated during coal beneficiation. When preparing CWSF, the optimum CWSF formulation must be determined to ensure that the fuel will be stable while having acceptable atomization and combustion properties, and the production run must be monitored closely to ensure that the CWSF quality is maintained. This paper describes the CWSF formulation process, CWSF preparation circuits, and some of typical problems encountered in, and solutions to, the transportation and storage of CWSF.

Jan 1, 1993

By S. Klein, M. McLeod, S. Gambino, K. Johnson, E. O’Hara

The Mokelumne Aqueducts Resiliency Project (MARP) involves construction of a 16.5-mile tunnel across the Sacramento-San Joaquin Delta (Delta) to replace the existing surface aqueduct pipelines with more resilient conveyance. The tunnel will be bored in Pleistocene-age alluvium at elevations between 100 to 10 feet below mean sea level. At this depth ground conditions are signicantly stiffer and denser than surcial soils and will mitigate potential seismic harards related to liquefaction ground shaking and cooding that could arise from potentially damaged levees. The heterogeneous soil deposits at tunnel depth consist of interbedded layers of stiff to very stiff clay and silt, and dense to very dense clean sand and silty sand.

Jun 23, 2024

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona&apos;s BHK System.

Jan 1, 1990

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.