Search Documents

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By J. W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct iron making pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicate that 69% are less than 2.5 µm across, 21 % are 2.5-5 µm, and 10% are larger than 5 µm. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2009 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on industry exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2009: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2009 and were compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2009, primarily for base metals (copper, lead, nickel and zinc), diamond and precious metals (gold, platinum-group metals and silver). Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis prior to 2008. The MEG survey methodology was changed in 1999 to include companies with exploration budgets greater than $100,000, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2009 survey is reported by MEG to cover an estimated 95 percent. Companies who chose not to participate in the MEG study, private companies that do not publish data and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 86 more companies in its 2009 survey than it did in 2008.

May 1, 2010

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Greg J. Hasenfus, Allison M. Haines, Joshua M. Silvis

The floodable volume of longwall gob can be of great importance in developing accurate coal mine operation plans, particularly for mine water management and environmental control strategies. Given the inaccessibility and difficulty in direct measurement of gob characteristics following gob recompression, hydrologic, geomechanical, and spatial data and principles were used to solve for the porosity and height of the residual gob using a mathematical model framework and bulking-based techniques. Based on this approach, gob porosity of Appalachian longwalls appears to be tighter than previously reported, ranging between 4.99 and 14.31%. Residual gob height, as normalized with respect to mine extraction height, ranges between 1.90 and 2.45. A novel, bedding-based bulking approach is ampliative with respect to existing roof caving and bulking fundamentals, as it has greater explanatory value compared with the traditional, lithologic-based bulking application. The efficacy of using the residual gob characteristics determined by the mathematical model and bedding-based bulking is examined using a causal comparative method, whereby time series prediction of historical groundwater rebound is compared with observed mine pool elevation data. Prediction accuracy is significantly improved using a prototype model to calculate void volume of longwall gob, specifically, the dependence of porosity of the gob material upon the longwall width to overburden depth ratio for movement basins of subcritical and critical panel widths. The potential implication of these findings toward hydrologic, geomechanical, and ventilation studies of longwall gob could be significant.

Aug 13, 2021

By R. Gradnik

The continuous need for infrastructure expansion forces the mining industry to develop underground structures into more sensitive and violent environments. When underground excavation enters into deep and high stress rock conditions, geotechnical designers find themselves faced with the difficult task of selecting a rock support system that will meet today's stringent requirements. Whatever support system is chosen, it is mandatory that potential rock movement be controlled. All this has intensified the development of safety systems and new, unique solutions which can enable construction companies to go both, further and deeper, without reducing the level of safety. To address these needs, Atlas Copco developed the Roofex® bolt, specifically designed to withstand large static and dynamic deformations under prespecified load conditions. The Roofex Rock Bolt acts as stiff support up to a designable load level before the sliding effect of the mechanical frictional system is triggered and allows highly controlled rock mass movement without loosing the support function.

Jan 1, 2011

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By J. G. Craig

This paper initially was to be on the design, construction and operation of the Lucky Friday mill. However, this subject has been pretty well covered in some of the mining publications in the past few years - specifically Mining Congress Journal for April, 1961 and Mining World for March, 1962- : In order to avoid too much repetition, we decided to present in this paper a comparison of the Lucky Friday mill constructed in 1959, and the Mayflower mill built by us in 1962. During the past three years Hecla Mining Company has constructed two relatively small mills: The Lucky Friday mill at Mullan, Idaho 750 T/day; and the Mayflower mill at Heber, Utah - 450 T/day. These mills were engineered, designed and constructed by Hecla, using principally our own personnel, with very little outside (contractor) labor employed. This paper presents a comparison of some of the interesting features of these mills, and where differences occur, it discusses the reasons for the various differences. It compares such points as the testing program, physical layout of the plant, construction costs, the grinding section, the flotation section, tailings disposal, metallurgy, recovery, grades, operating costs, etc. To help illustrate, and to compare these features, we will project pairs of slides showing each of the two mills. First a little background and history on the properties ---

Jan 1, 1964

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), the authors showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/tonne of REEs occur in AMD and AMDp respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. Geospatial analysis identified a total resource of 340 tonnes stored at the 141 sites sampled in this study. While this analysis did not quantify the basin-wide REE inventory, it does indicate the impact that processing cut-off grades will have on the overall AMDp resource base.

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimum when the concentration of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/ liquid ratio of 67 g/L, stirring speed of 400 rpm, and leaching duration of 60 min. Under this condition, 90.49% and 6.78% of Mn and Fe were dissolved, respectively, from the ore sample with a size fraction of − 106 μm. It was determined that the leaching of manganese from the ores was a second-order reaction with an activation energy (Ea) of 53.38 kJ/mol. The leaching residues obtained under the optimum condition were subjected to high-intensity wet magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20% Fe and 1.79% Mn with iron and manganese recoveries of 56.83% and 66.73%, respectively. A magnetic separation test from an unleached ore sample was also carried out as a benchmark. To the best of our knowledge, this is the first time that a magnetic separation process was used to a residue obtained from reductive acid leaching of manganiferous iron ores to recover iron.

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By Charles W. Daugherty

INTRODUCTION The Washington Metropolitan Area Transit Authority's (WMATA's) rapid transit system, Metro, ultimately will comprise 162.5 km (101 miles) of line divided among 10 routes. As shown in Figure 1, about 24 km (15 miles) of the system will consist of mined rock tunnels distributed along the A, B, C and K Routes. The structural construction contracts for all of the A, C and K Route rock tunnels are complete and trains are running in about one-third of them. A contract for construction of rock tunnel section B-9, the southernmost third of the B Route, was awarded on June 27, 1980. The final design of Sections B-10 and B-lla, the remainder of the rock tunnel portions of the B Route and the Metro system, are well advanced and should be under con¬struction by 1982. Of Metro's 87 stations, 11 will have been constructed by mining in solid rock, a not inconsiderable achievement, since each structure must be over 183 m (600 feet) long, wide enough to accommodate two trains and one or two passenger platforms, and high enough to achieve a stable arching action without encumbering columns. With the passage of years, some original priorities have been reordered, and ways have been sought to streamline and simplify this most complex of Metro structures without grossly violating the architectural standards that make it unique. This paper will summarize that search, and describe the design and construction aspects of the resulting product, the dual chamber rock tunnel station.

Jan 1, 1981

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress in underground coal mines is a major threat to the health and safety of the miners. Hence, managing heat and prediction of heat stress in advance is essential for maintaining a safe, healthy, and productive underground mine environment. In this study, an extensive ventilation survey has been carried out in three different deep and mechanized underground coal mines. The ventilation survey data are used to develop 3D simulation models with the VentSim™ software to predict the conditions that could cause heat stress in underground mine workings. The developed 3D models predicted well the wet-bulb globe temperature (WBGT), a recognized indicator of potential heat stress, with a coefficient of determination (R2) of 0.986, 0.994, and 0.993 for Mine-A, Mine-B, and Mine-C, respectively. Moreover, through 3D modelling, the applications of auxiliary ventilation and spot coolers to reduce the wet-bulb globe temperature (WBGT) for improving the underground workplace environment have been explored. The study demonstrated that auxiliary ventilation and spot coolers can help in significant reduction of heat stress conditions in an underground mine environment. By application of auxiliary ventilation, to increase air volumes, and spot coolers, the WBGT index in mining faces is reduced by 1.2–1.4 °C and 3.9–5.4 °C, respectively. Therefore, it is concluded that the spot coolers are more effective in reducing the heat stress conditions in hot and humid underground mine environments in comparison with auxiliary fan that is used to increase the air volume and velocity. This study opens up a new horizon of 3D simulations for heat stress management in underground mines. The outcome of this study will be useful for the researchers, mine operators, and environmentalists understanding the heat stress contributors and their control in underground mine environment.

May 10, 2023

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.