Search Documents

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By C. J. Fauconnier

The main purpose of the paper is to determine the contribution of fluctuations in barometric pressure to flammable gas explosions in South African mines. For this purpose, the barometric-pressure patterns preceding each of the 59 major explosions in South African gold and coal mines over the past 20 years were analysed. It is concluded that diurnal fluctuations in pressure do not have a major influence on the accumulation of gas in the underground workings, but that pressure drops associated with cyclonic weather systems moving across the country over a number of days are the major factor contributing to gas explosions in mines. To illustrate some of the points made in the paper, the Hlobane Colliery explosion of September 1983 is used as a case study. In the final section, several general conclusions are drawn and recommendations put forward as to how mines should recognize and react to meteorological phenomena that may lead to an increased probability of gas explosions in underground workings.

Jan 1, 1992

By D. Limpitlaw

As coal mining often results in the generation of acid mine drainage (AMD), careful planning and management of the water on such mines is required. A colliery in Mpumalanga recently sponsored independent research into the pollution-ameliorating potential of a natural wetland that has been receiving AMD for at least two decades. Samples of the sediment collected in the wetland were subjected to nine stages of sequential extraction in a determination of the distribution of the metal species present. The samples were then analysed for aluminium, iron, and manganese. The concentrations of sulphate-reducing bacteria (SRB) were also determined. The SRB concentration was found to increase with distance downstream (away from the source of pollution). An analysis of the sediment speciation data indicated that metal immobilization may be optimal in areas where the organic adsorption of metals is at its greatest. The analysis also provided evidence of the biogeochemical improvement of the water quality as the AMD passed through the wetland environment. The metal species present did not correlate strongly with the SRB populations; nor did the soluble species correlate with the species formed over long periods of time.

Jan 1, 1996

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar

An electrochemical technique based on the solid oxide galvanic cel Mo / Mo + MoO2/ ZrO2-MgO / Fe + (FexO)slag + Ag / Fe was used in a determination of FexO activities in liquid slag systems. The emf measurements, scanning electron microscopy, and microprobe analysis of the cross-sections of the electrolyte tubes used in direct contact with the slag melts indicated that slag attack did not affect the open-circuit emf values during normal cell operation, The reliability of the cell was confirmed by the good agreement between the standard free energy of formation of liquid Fep obtained in the present study and those reported in the literature, The FexO activities were determined in FexO -CaO and FexO-SiO2 slags at 1673 K, and are in good agreement with those measured by the conventional gas-equilibrium technique. The experimental technique was successfully extended to the measurement of Fe2O activities in the complex slags that are used for the external desilliconization of the hot metal product of the blast furnace.

Jan 1, 1986

By M. W. Hildyard, J. A. L. Napier

The improved design of support systems and stoping strategies when changes in depth, stratigraphy, or mine layouts are considered must rely on the designer's fundamental understanding of the deformation mechanisms adjacent to underground openings so that he can extrapolate and predict expected mining conditions. This paper presents a numerical approach to the modeling of the growth and interaction of mining-induced fractures near the edges of deep tabular excavations in brittle rock. Fractures are represented by displacement-discontinuity elements that are allowed to propagate according to prescribed growth rules. This procedure is justified by the reproduction of several features observed in laboratory simulations of fracturing around openings in blocks of rock subjected to uniaxial and biaxial compression. An attempt is then made to explain some of the attributes of the fracture zone surrounding tabular stopes. Particular questions of interest are the sequence in which fractures form and are mobilized in front of the mining face, the effect of parting planes parallel to the plane of the excavation, and the distribution of stress parallel to the hangingwall and footwall.

Jan 1, 1992

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By M. L. Smith

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By M. Akyüzlü

The equilibrium between carbon-saturated Fe-Cr-Si-C alloys and SiO2-CaO-MgO-A2O3-CrO2-FeOy slags was studied under atmospheres of argon and carbon monoxide at temperatures of 1500 and 1600°C. The equilibrium distribution of chromium, silicon, and iron between the slag and the metal phases was determined for different compositions of both phases under different atmospheres and temperatures. It is shown that silicon transfer from the slag to the metal increases with increasing temperature, decreasing carbon monoxide partial pressure, decreasing carbon content of the metal, increasing chromium-to-iron ratio of the metal, increasing silica content of the slag, and decreasing lime-to-alumina ratio of the slag. Some activity calculations were made for the experiments conducted at 1600OC in a carbon monoxide atmosphere. It is also shown that a decrease in the iron content and an increase in the slag basicity decrease the chromium content of the slag. A major proportion of the chromium present in the slag was found to be in the divalent state under the highly reducing conditions prevailing in the experiments. The chromous capacities of these slags were calculated and were found to decrease with increasing basicity.

Jan 1, 1992

By R. H. C. Andrew

With the advent in recent years qf mechanization in deep-level gold and platinum mines, large quantities of rubber was are being used on both production and support vehicles. Conditions in these types of mines are extremely harsh and, as a result, we performance is significantly lower than in other types of mining such as open-cast base metal mining, where more favourable conditions prevail. Various options are available to the user to reduce tyre costs, including the use of retreads, the filing of tyres, and the repair of damaged tyres. While these methods may be generally successful in open-cast conditions, their use in deep-level mining needs to be carefully evaluated for each particular set of conditions. A basic requirement for any evaluation of we costs is the availability of reliable data on tyre performance and, for this reason, it is essential that proper tyre records are maintained This paper reviews the performance of tyres in deep-level gold and platinum mines in Johannesburg Consolidated Investment Company, Limited (JCI) over a period of about 8 years, and shows how the costs of retreading and tyre filing can be evaluated in practice. It also discusses the cost implications of repairing damaged tyres.

Jan 1, 1994

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

At the Annual General Meeting of the Chamber of Mines of South Africa, held in Johannesburg on 29th June, 1982, the following leading members of the mining industry were elected to office for the 1982-1983 term: Mr W. W. Malan President Mr C. T. Fenton Vice-President Mr G. Y. Nisbet Vice President William Wouter Malan was born in Springs on 7th November, 1928, and was educated at the Springs High School and the University of the Witwatersrand, where he obtained a B.8c degree in mining engineering. Diamond Mines. Mr Nisbet became a consulting engineer of the Anglo American Corporation in 1972, and a deputy managing director of the Gold Division in 1974. George Young Kisbet was born in Benoni in 1923 and was educated at Pretoria Boys High and the University of the Witwatersrand. Mintek reports Report 2010D A process for the recovery of rare-earth oxides from monazite. (First published 16th March, 1979). Report 2073D A preliminary investigation of the concentration process at Ucar Minerals Corporation. (First published 19th September, 1980). Report 2092D The recovery of pyrite from gold ore by gravity separation. (First published 28th November, 1980). Report M13 Factors affecting the production of fines during the screening and handling of highcarbon ferromanganese.

Jan 1, 1982

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By R. Van Rijswick

Crankshaft driven piston and piston diaphragm pumps inherently generate a varying flow each crankshaft revolution. Depending on the system connected, this flow variation results in a pressure pulsation. This pressure pulsation may, depending on the structural design, result in structural vibrations. In order to limit the level of pressure pulsations, volume absorbing devices, mostly gas filled vessels, are used. The standard selection of these so-called dampeners is based on the flow variation of the pump but does not incorporate the interaction with the connected system. The paper discusses the application of a pulsation analysis tool developed by WEIR Minerals Netherlands, manufacturer of GEHO positive displacement slurry pumps. The paper first discusses the basics of pressure pulsation analysis, such as flow variation generated by crankshaft driven pumps, and hydraulic effects such as capacitance, inductance and resistance and their influence on the hydraulic response of a system. Furthermore, the relation between pressure pulsations and structural vibrations, known as fluid structure interaction, will be discussed. Additionally, the capabilities of the pump pulsation analysis tool are presented, illustrated by examples of simulation results and experimental verification.

Jan 1, 2007

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By H. J. Swanepoel, N. B. Strydom

Groups of up to twelve new recruits to the industry were subjected to climatic room acclimatization for either five, seven, eight or nine days prior to being tested for the degree to which they had been acclimatized. These tests were done at 32,2 0C (wet bulb) at a wind velocity of about 0,4 m/sec and the men worked for four hours at a rate of 215,6 kg m/min on one day and at a rate of 431,2 kg m/min on the second day. The results indicated that there is no significant difference between the degrees of acclimatization obtained by the eight- and nineday procedures which confirms the conculsions drawn in a previous report1. The eight-day procedure can thus be claimed to be perfectly adequate and safe. Decreasing the period of exposure to five or seven days would however, not be justified because of the significant differences in physiological responses that were observed on both test days between men acclimatized for these periods and those acclimatized for nine days. It is concluded that it would be unsafe to employ these shorter periods of acclimatization when underground environmental temperatures at which the men are to work, exceed 31 0C (wet bulb).

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By E. A. Brinkmann

A kinetic model framework for single particle kinetics in combined diffusion and adsorption processes is presented. The framework applies to the general case in which both diffusion and the adsorption reaction play important roles in determining the overall rate in processes where the migrating species can both adsorb and accumulate. The technique, which should be applicable to a wide range of reaction mechanisms, consists of an iterative integration procedure for the coupled diffusion and reaction equations. The case of a reversible linear adsorption reaction rate is developed. In order to verify the technique as a legitimate method of model development, an analytical solution for the identical case is derived and compared to the numerical solution. Excellent agreement exists between the two solutions.

Jan 1, 1987

By M. M. Oosterveld

Diamonds are mined from ancient raised beach deposits in southern Namibia where complex geological controls have resulted in patchy diamond distribution, largely related to irregularities (trapsites) in the bedrock. The distribution of the number of diamonds per sample is a discrete, reverse- J shape distribution which can be characterized by two parameters. These parameters have been transformed into a Beta and Theta Contribution which can be interpreted as reflecting the &apos;quantity&apos; and &apos;quality&apos; of the trapsites. The relationship of statistical parameters, obtained during the sampling of an ore deposit, to the geology of the deposit is an important element of ore reserve estimation. The large-scale regional trends in the contributions have been explained in terms of the geology.

Jan 1, 1987

The refractoriness of the gold in many of the pyritic ores from the eastern Transvaal is due mainly to the association between the gold and the sulphides, but it can be due to the presence of graphltlc carbonaceous material, which complicates the recovery of the gold by virtue of its adsorption activity. In an examination of the roasting characteristics of three flotation concentrates from the Barberton area, It was found that the gold in the concentrates occurred mostly in two forms: in very fine gold particles distributed within the arsenopyrite, and in a slightly coarser form loosely associated with the pyrite. Direct cyanidation of the concentrates gave gold extractions of from 16 to 30 per cent. After the concentrates had been roasted at temperatures of 650 to 700°C for 20 minutes with rabbling, the extractions varied from 86 to over 90 per cent. Examination of the residues after cyanidation indicated that gold was present in the porous calcines or in the calcined sulphide product. This observation, together with porosity measurements, suggests that physical encapsulation of the gold particles is the main reason for the refractory behaviour of the gold in the calcines.

Jan 1, 1988