Search Documents

By J. Hadjigeorgiou, G. Knox

Since their introduction in 2010, paddled energy-absorbing rockbolts have been widely used in seismically active hard rock mines. This paper provides new data and reviews previous work to quantify the performance of paddled energy-absorbing rockbolts under controlled laboratory conditions. Of significance is the realization that the typical split location in impact tests, at the centre between two paddle anchor points can at best provide an upper limit value. This inherent variability in performance under different testing configurations should be acknowledged and taken into consideration in the design of ground support in seismic conditions. This paper discusses the reduction in capacity of paddled rockbolts as a function of loading angle from a maximum value during axial tests (0° loading angle) to the lowest value during pure shear (loading angle of 90°). A significant reduction in displacement capacity is observed as the loading angle changes between axial (0°) and 40°. Beyond a 40° loading angle up to shear (90°) loading the reduction in displacement capacity is less significant. Due to the variances in the capacity observed through the variance of the testing configuration: loading mechanism, direction of loading, location / presence of a discontinuity, it must be recognized that results from laboratory-based testing are not independent of the testing configuration. This should be acknowledged when extrapolating anticipated performance in the field.

Oct 9, 2024

By P. Linzer, L. M. Linzer

The gravity method is often applied in mining-related scenarios such as geological and mineral exploration, detecting subsurface cavities and voids (“receptacles”) that may become sinkholes, siting of surface structures, fault-mapping, and more. It is also widely applied in geotechnical engineering to map subsurface karst profiles and to detect subsurface cavities, such as can occur in open pit mines. While it is widely acknowledged that, compared with other available geophysical methods, this method is the most applicable to the karst profiling problem, survey geometries applied in the field are often far from optimal. The gravity surveying specifications prescribed in SANS 1936 omit some key requirements for optimal survey outcomes, and this paper is intended to fill those gaps. The authors have seen scopes of work that require only a few measurements over the footprint of a proposed structure, indicating a lack of understanding of the nature of the gravitational field. A single gravity measurement is subject to the camouflaging effects of several influences, many of which can be larger than the anomaly caused by the subsurface density variation itself. Papers in the body of literature show an awareness of the need to map the regional field so that it can be subtracted to unmask the residual gravity anomaly, but rarely do they examine how instrument sensitivity governs the size of detectable anomalies or discuss how a detailed terrain correction can be instrumental for isolating faint targets. This paper aims to explain how to apply the gravity method correctly to mining and geotechnical problems, specifically in the detection of subsurface cavities. It discusses various factors to assist with optimising the acquisition of gravity data and its processing so as to maximise the practical value of gravity surveys.

Sep 1, 2025

By J. W. van der Merwe, K. G. Moloko

Furnace wall tubes from 600 MW subcritical boilers at three coal-fired power stations were sampled and the fireside deposits examined to determine the mechanism of fireside corrosion. This involved an indepth investigation into the morphology and composition of the fireside deposits and the conditions of the furnace that enable this type of attack. SEM-EDS analysis revealed high concentrations of oxygen, iron, and sulphur, QEMSCAN and XRD analyses identified the presence of Fe3O4, Fe2O3, FeS, and FeS2. Differential thermal analysis showed thermal activities at temperatures of 500–600°C, 900–1100°C, and 1100–1250°C, which are associated, respectively, with FeS2 oxidation to FeS and Fe2O3, at 475–525°C, formation of aluminosilicates at 925–1100°C, and melting of FeS around 1190°C. The absence of sodium and potassium eliminates the contribution of molten alkali sulphates to the corrosion. The consistent coexistence of iron sulphide and iron oxide is indicative of the substoichiometric conditions in the furnace, while the detection of pyrite suggests that the coal is not completely combusted, which points to a poor combustion process. These observations were affirmed by gas analysis at one of the stations, where very high levels of carbon monoxide were measured at the furnace wall (≥ 14 000 ppm) and furnace exit (≥ 3500 ppm). The high CO concentrations are indicative of limited combustion caused by limited O2. These reducing conditions promote the formation of FeS-rich deposit, which is the corrosive species responsible for degradation.

Jun 1, 2021

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025

By M. Mpofu, G. Stenzel, F. Magweregwede, B. Maphalala, T. Kgarume

Surface coal operations in which mining activities are conducted above old underground workings experience hot holes after drilling. In a coal mine, hot holes are defined as shot holes, which after being drilled have an in-hole ambient temperature of 40°C or above or show a temperature increase of 3°C or more during monitoring. Hot holes and other cavities, such as cracks, pose health and safety risks to workers, such as exposure to hot air and high concentrations of noxious gases released from these holes. In addition, workers may be exposed to premature detonation of explosives caused by in-hole temperature increases and chemical reactions. To this end, Coaltech Research Association commissioned a project to develop a Best Practice Guideline for the management of hot holes. This paper is a compilation of the activities conducted in the development of the Best Practice Guideline between 2021 and 2022. The activities included a review of standard operating procedures and hot-hole temperature-measuring and -monitoring devices, and the assessment of current hot-hole procedures at selected mines. The results indicated that management of hot holes requires a focus on pre-emptive risk assessment of mining blocks, identification of hot holes using the correct temperature-measuring devices, and continuous monitoring of hot holes from the time of drilling until just before blasting. Hot-hole management accessories, such as polyvinyl chloride sleeves, were found to be effective in insulating the hot-hole emulsion from the rock mass temperature, thus preventing the potential for premature detonation.

Sep 9, 2024

By B. Maybee, J. Venter, J. Wesseloo

The selection of open-pit slope angles involves high-value decisions with small changes in slope angle, often representing significant changes in net present value. The existing methods used to define design acceptance criteria have evolved from factor of safety to probability of failure (P[F]) to risk consequence to risk frontiers, which represents current state of the art. Current design acceptance measures are based on references to published tables representing the experience and judgement of their authors, who did not specify the purpose of the measures contained therein. As the purpose of the published design acceptance criteria is not specified (i.e., definite stability, marginal stability, optimization, etc.), such tables cannot be used to achieve optimum slope angles that maximize profitability. This paper develops a design acceptance criterion that maximizes profitability by defining a formulation for optimum risk that balances expected risk and reward. The model developed is titled the Mining Risk Model (MRM), and is applied to open-pit slope angle selection through an equation for optimum probability of downside (P[D]O) that balances the upside or opportunity, the P[F], and the downside impact. This formulation for optimum risk is unique, as many authors have presented objective functions for their risk models that can be optimized, but none of the sources reviewed contained a formulation for optimum risk. The MRM is sufficiently flexible to allow the design performance measure that drives P[F], and hence P[D]O, to be selected based on the intended goal. Furthermore, the essential information that must be known to quantify optimum risk is defined. This allows users to determine what information to collect for optimum risk decisions. A further benefit of the MRM is that slope angle decisions and pit shells can be ranked to select the best option, and a threshold is provided that separates acceptable from unacceptable decisions. Finally, the workflow and information required to determine optimum risk are presented.

Sep 9, 2024

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 25th August, 1971, at 4.15 p.m. Mr V. C. Robinson (President) was in the Chair. There were also present fifty one Fellows, twenty one Members, two Associates, two Students and fourteen Visitors, making a total of ninety one. The President declared the meeting open at 4.15 p.m. OBITUARIES The President: 'It is my sad duty to announce the death of the following members of the institute: H. J. G. C. Arndt, Life Member, joined 1933, passed away 11th May, 1971. J. H. A. Diering, Fellow, joined 1921, passed away 24th June, 1971. L. O. W. Leimer, Fellow, joined 1960, passed away 25th June, 1971. E. A. Meltzer, Fellow, joined 1941, passed away April, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 17th March, 1971, as published in the July, 1971 issue of the Journal?' Agreed. WELCOME TO VISITORS The President: In welcoming you here, ladies and gentlemen, it gives me great pleasure to see so many of our office bearers-our important honorary office bearers-and particularly I would like to welcome our Honorary President, who is, as you know, the President of the Chamber of Mines, Mr John Shilling, and we are 'privileged also to have with us two of our Honorary Vice-Presidents. One in particular I am very pleased to welcome here, and that is Mr G. F. van L. Froneman, who is the Administrator of the Orange Free State, and we extend a very hearty welcome to him, because he is a long way from home. Then we have another Honorary Vice-President, Mr Tommy Gibbs, the Government Mining Engineer, and there are many distinguished guests, whose names I want to give you, so that you will know who they are. We are happy to have present: Mr R. C. J. Goode, Member of Council, I.M.M. London; Mr E. Boden, Manager, A.S. & T.S. of S.A.; Mr G. A. P. Louw, The President, The Associated Scientific and Technical Societies of S.A.; Mr I. R. G. Stephen, The President, The South African Institution of Electrical Engineers; Mr A. S. Robinson, The President, The South African Institution of Civil Engineers; Mr C. F. J. Schneider, The President, The Institute of Land Surveyors of the Transvaal; Mr R. J. Vermaak, The President, The South African Institute of Assayers & Analysts; Prof J. P. F. Sellschop, The President, Joint Council of S.A. Scientific Societies; Mr T. C. Watermeyer, The President, The Federation of Societies of Professional Engineers; Mr G. A. MacWhirther, The President, S.E.I.F.S.A.; Mr C. G. Hinds, The President, The Mine Managers Association; Mr J. F. Aldersley, The President, The South African Institute of Foundrymen; Dr H. O. Reisener, The President, The Institute of Welding; Dr F. P. A. Robinson, The President, S.A. Corrosion Council; Mr A. Bain, The Chairman, Witbank-Middelburg Branch; Prof D. J. Schoeman, The Chairman, The S.A. Institution of Chemical Engineers; Dr N. P. Finkelstein, The Chairman, The South African Chemical Institute (S.Tvl Section); Mr J. M. Meyer, Chairman, O.F.S. Branch. To all these guests and their ladies, I extend a most cordial welcome, and hope that you are going to enjoy the afternoon. MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates having been published in accordance with By-Law 5.2.2., Council has elected them to membership in the following grades: Fellows: Richard Lloyd Blandy, Byron J. Haley. Members: Brian Roger Borton, Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom. Students: Peter Boesley James, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade. ANNUAL REPORT OF THE COUNCIL AND ACCOUNTS FOR THE YEAR ENDED 30TH JUNE 1971 THE PRESIDENT: We now come, ladies and gentlemen, to the annual report of the Council of the Institute-and our accounts for the year ended 30th June, 1971, and these documents are on your chairs; I know you probably haven't had time to study them yet, but I would like to highlight some of the things which I think are worth mentioning. I would ask you to take, first of all, ladies and gentlemen, the report of the Council as being read, and before moving adoption, however, there are certain salient points I wish to touch on, and I will leave the financial side of this entirely to our very competent and worthy, Honorary Treasurer, Mr Denis Maxwell.

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 22nd August, 1973. Dr J. P. Hugo (President) was in the Chair. There were also present 64 Fellows, 20 Members, 5 Associates, 3 Students, and 34 Visitors, making a total of 126. The President declared the meeting open at 4.05 p.m. OBITUARIES The President: It is my sad duty to announce the death of the following members of the Institute C. Boocock, R. J. G. Moore, M. P. Pearse, and A. I. Sussman, all Fellows, and W. T. Dalling, a Life Member. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments' silence. MINUTES Die President: Item twee op die agenda is die bekragtiging van die notules van die jongste Algemene Vergadering van die Instituut. Daar die notules in die Augustus uitgawe van die Joernaal gepubliseer is, vra ek u toestemming dat dit as sulks bekragtig word. Toestemming verleen. WELCOME TO VISITORS The President: It is my very great pleasure to welcome all the distinguished guests who have honoured us with their presence this afternoon; in particular, a hearty word of welcome to the Honorary President of the Institute, Mr Plumbridge, the President of the Chamber of Mines. You are doubly welcome here, sir, and we thank you for your presence. Also to that old member and stalwart, the Honorary Vice-President of the Institute, Mr Tommy Gibbs, the Government Mining Engineer-you're very welcome, Mr Gibbs. Then, we are particularly privileged this afternoon to have an Honorary Member with us, the Minister of Mines for Rhodesia, Mr Dillon. You will recall that he honoured us with his company last year. Mr Dillon, we are very appreciative and hope that this is now a standing arrangement. We are also honoured by the presence of some thirteen Presidents, Vice-Presidents, or Chairmen of our sister scientific and technical organizations. I shall rapidly read their names, but they must all feel assured that they are very welcome here today. Firstly, one of our own Past Presidents and members, Mr Geoff Goode in his capacity as President of the Associated Scientific and Technical Societies of South Africa; Mr L. R. Robinson, President of the South African Institution of Mechanical Engineers, and Mrs Robinson; Mr G. Goedhals, President of the South African Institute of Electrical Engineers ; Dr Antrobus, President of the Geological Society of South Africa, and Mrs Antrobus; Mr T. V. Dean, Vice-President of the Institute of Land Surveyors of the Transvaal, and Mrs Dean; Mr R. M. Stroh, President of the Mine Ventilation Society of South Africa; Mr Ken Steele, President of the Association of Mine Managers, and Mrs Steele; Mr Mike Gericke, President of the South African Council for Professional Engineers; Mr R. G. Matthews, President of the Institute of Mine Surveyors of South Africa; Mr P. H. Pettifor, President of the Institute of Production Engineers, London, and Mrs Pettifor ; Dr Nico Stutterheim, Chairman of the South African Institute of Chemical Engineers, and Mrs Stutterheim; Professor F. A. van Duuren, Chairman of the Engineers' Liaison Committee in Pretoria; also, I haven't spotted him but I trust he is here-Mr Alex Bain, who is Chairman of this Institute's Witbank/Middelburg Branch. To one and all, ladies and gentlemen, a hearty word of welcome. Not last on our list, a word of welcome to Mr Eric Boden, the Manager of A.S. and T.S. We also have with us I trust, Dr Deist, and his good lady-Dr Deist will be figuring in our proceedings later this afternoon. Also Mr Barcza and Mrs Barcza. Mr Bareza, a former President of the Institute, also has a task to perform. Then, I hope two of our student prize winners are here-Mr Beetge and Mr Painting. Then we also have Mr Roberts, who is welcome in his capacity as co-author with Dr Deist. Then, last of all, a hearty word of welcome to Dr Helen Glen (I am not sure whether she has arrived yet, but she is certainly due to come)-the new Honorary Editor of the Institute's Journal. MEMBERSHIP The President: I have pleasure in announcing that, their names having been published in accordance with By-law 5.2.2, the following have been elected by Council to membership in the following grades Fellows: W. G. Jayes and F. K. Wright Members: D. W. Penman, A. W. Bryson, and D. L. Gibbs Graduates: R. J. Adey, J. P. Bond, R. C. Dunne, G. M. Entwhistle, J. M. Rendu, J. P. S. Turner, and A. P. van Jaarsveld Associates: A. Ellis, B. R. Hambly, A. J. Johansen, and G. W. Tregoning

Jan 10, 1973

A General Meeting and Colloquium was held in Kelvin House, Johannesburg on Wednesday 29th September, 1971. The theme of the Colloquium was "The Ferro-alloy Industry". Prof D. D. Howat (President) was in the Chair. The meeting was attended by 106 delegates and was opened by the President at 10.05 a.m. OBITUARY The President: "It is my sad duty to announce the death of G. C. Needham, Fellow, who joined the Institute in 1966 and passed away on 27th September, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence." MEMBERSHIP The President: "I have much pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute. Fellows: Richard Lloyd Blandy, Brian Roger Borton, Brian Teversham, Peter Donald Dickson. Members: Frederick Brian Peacock, Peter John Stacey, Kenneth Niles Thanstrom, Byron J. Hayley, Ian Flemming Buchan, Abraham Hercules le Roux. Graduate: Ian William Coy. Students: Peter Boesley J ames, Kenneth Brian Perel. TRANSFERS From Member to Fellow: Cecil Eugene Fivaz, Peter Edwards. From Student to Graduate: Roy Stavely Traviss. From Student to associate: William Mitchell. I welcome the new members to the Institute and congratulate those members who have been transferred to a higher grade. COLLOQUIUM The first paper, presented by Mr S. Selmer-Olsen, Consulting Metallurgist, Amcor Limited, on 'Trends in Ferro Alloy Production' was published in the May issue of the Journal and comprised information and data relating to new developments in ferro alloy production in various parts of the world. This was followed by a paper-'Conductivity and Viscosity Properties of Slags produced in ferro-alloy manufacture' by D. 1. Ossin et al. This was a record of laboratory test work on slags containing both lime and magnesia, corresponding with the composition of slags encountered in the production of ferro chrome alloys when a dolomite flux is employed. The third paper-'Review of the work of the Pyrometallurgical Research Group of N.I.M. and Metallurgy Department, Wits.' presented by Dr P. R. Jochens, leader of the Research Group, outlined the progress made on ten different research projects presently under way in the Department of Metallurgy. These projects range from studies of the kinetics and mechanism of the reduction of chromite ores through the determination of the activities of MnO in slags to phase studies and melting point determinations in the alloy systems Cr-Fe-Si-C and Cr-Fe-Si. A new feature of this Colloquium was the introduction of the discussion panel composed of four or five individuals known to have special knowledge or interest in the subject under duscussion. Mr J. J. Coetzee was chairman of the first panel, Professor D. D. Howat of the second and Dr R. E. Robinson of the third. During the discussion of Mr Selmer-Olsen's paper an interesting contribution was made by Mr Jack Hayley of Transalloys (Pty.) Limited who pointed out that the lowest power cost in the U.S.A. was that from the TV A at 6 mils per unit (0,43 cents S.A.) while costs from other sources were 7 to 8 mils per unit (0,50 to 0,57 cents S.A.) He also referred to the use of 'pile sintering' of ore fines plus coke at certain ferro alloy plants in the V.S. and to the recent practice of 'graphitising' the paste used for Soderberg electrodes. The last session in the afternoon was devoted to a group discussion on 'Practical problems in Arc Furnace Operation', Mr H. R. Reid of Middelburg Steel Alloys (Pty) Limited occupying the chair, members of the panel being Mr J. Meintjies (Rand Carbide Limited), Mr J. Benn (Amcor) and Mr E. J. Jackson (Transalloys (Pty.) Limited). Mr Reid initiated the discussion by talking of the design and composition of electrode shoes, mentioning the use of the 85/15 Cu/Zn alloy and the comparison of hollow shoes and shoes cooled by tubes. Mr Meintjies discussed electrode management with particular reference to breakages, and dealt with casing and fin design and the welding of fins. Mr Benn dealt with aspects of closed top furnace operation with particular reference to the control of eruptions in the furnace and indicated that preheating of the raw materials might be well worth considering together with the development of a system for the detection of the water vapour present. Mr J ackson was concerned with shells, linings, refractories and tap holes. He deprecated the use of oxygen for opening the tap hole emphasising how uncontrolled use of oxygen led to loss of shape of the tap hole and quite severe burning out of the front hole resulting in time and labour in repairs. A notable feature of the Colloquium was the free discussion 'from the floor' of the hall. Many valuable and highly pertinent contributions were made spontaneously and usually in reply to some controversial topic raised by the discussion group.

SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg in June 1969, may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal, at the reduced price of R5.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). "The world sulphur position," by W. C. J. van Rensburg (Member). "The South African sulphur position," by D. L. Taylor (Member). "The recovery of pyrite at Government Gold Mining Areas Limited," by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. P. Carlisle (Member). "Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment," by W. A. Gilbert (Visitor) and E. A. Nugent (Member). "The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process," by D. J. Tutt (Associate Member). "Pyrite recovery by jigs at Durban Roodepoort Deep Limited," by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). "The storage of pyrite concentrates," by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). "The flotation plants of the Anglo-Transvaal Group," by L. A. Bushell (Member). "Pyrite flotation with amines and cyanidation of the products," by E. H. D. Carman (Member). "Gold recovery by cyanidation from mill products obtained after pyrite flotation," by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). "The influence of sulphydryl and cationic flotation reagents on cyanidation of native gold," by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). "Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector," by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy). INCOME TAX: POST-GRADUATE STUDY COURSE CONCESSION As a result of representations made by the Associated Scientific and Technical Societies of S.A. and the Suid-Afrikaanse Akademie vir Wetenskap en Kuns, engineers and scientists will now be allowed to deduct expenses incurred on post-graduate study courses from their taxable income. The conditions of this concession are set out in section 16 of the Income Tax Act, 1969, which reads as follows: 16. (1) The following section is hereby substituted for section 16 of the principal Act: 16. "Notwithstanding the provisions of section 23(a) and (b), there shall be allowed to be deducted from the income of any person who is a dentist or medical practitioner or practises any profession referred to in paragraph (a), so much as the Secretary may allow of any expenditure incurred by such person in the circumstances contemplated in paragraph (c), if the Dental Association of South Africa in the case of a dentist, or the Medical Association of South Africa in the case of a medical practitioner, or the "Suid-Afrikaanse Akademie vir Wetenskap en Kuns" or the Associated Scientific and Technical Societies of South Africa in any other case, certifies in such form as the Secretary may prescribe that such person- (a) if he is not a dentist or medical practitioner, is the holder of a degree in engineering or allied technology or natural sciences awarded by a recognized university on completion of a prescribed minimum period of study of not less than four academic years or the equivalent thereof and enabling the holder thereof to practise the profession of an engineer or a profession for which advanced and specialised scientific knowledge is required which relates directly to- (i) the development or exploitation of natural resources; (ii) mining or prospecting for minerals; (iii) the production of pastoral, agricultural or forest produce ; (iv) the breeding or care of farm animals; (v) any industrial process; or (vi) the training of specialists in any branch of science or technology connected with any aforementioned profession; (b) has practised his profession for not less than three years; and (c) has incurred such expenditure during the year of assessment in respect of the attendance by him of any postgraduate study course approved by such body to improve his qualifications for carrying on his profession in the Republic". (2) The amendments effected by subsection (1) shall first take effect in respect of assessments for the year of assessment ending on the twenty-eighth day of February, 1970. From this section it is clear that the concession will only be granted if the application is accompanied by a certificate, which certificate must be either signed by the Chairman of Die Akademie or the President of the Associated Societies. In terms of the authority granted such certificates must certify that: (i) the taxpayer concerned has practised his profession for not less than three years; (ii) the expenditure was incurred by the taxpayer during the year of assessment indicated in the certificate; (iii) the expenditure was incurred by the taxpayer in respect of the attendance by him of a post-graduate study course approved by the Associated Scientific and Technical Societies of South Africa or Die Suid-Afrikaanse Akademie vir Wetenskap en Kuns, as the case may be, to improve his qualifications for carrying on his profession in South Africa; (iv) the taxpayer is the holder of a degree in engineering or allied technology or natural sciences, which degree was awarded by a recognized university,

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publicatiol1 of technical notes taking up to three pages (maximum 3000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute asa body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By J. U. Burger

The Elizabeth Bay aeolian deposit in Namibia comprises a sedimentary package of diamondiferous grits that have been deposited, reworked and concentrated to various degrees by dominant southerly winds. Diamond concentration in these deposits is highly variable and often unpredictable. The deposit is marginal from an economic perspective and therefore requires selective mining which in turn requires correct sampling and accurate estimation. Three methods of sampling have been used at Elizabeth Bay for mineral resource estimation: (i) pit samples utilizing an excavator to produce a sample 1 to 3 metres deep with a 10 to 20 m2 footprint, (ii)GB50 grab sampling with a 3.34 m2 footprint and (iii) a BG36 bucket auger drill with a 5 m2 footprint. Pit sampling, being easy to execute, has been the most widely used despite a limited penetration ability and, at times, questionable integrity. The GB50 grab sampling tool was tested at Elizabeth Bay and although it had better penetration ability and sample integrity, it struggled with cemented horizons. No sample optimization was conducted prior to the GB50 grab sampling. The latest phase of sampling was conducted using a BG36 bucket auger drill which is capable of penetrating thick overburden, penetrate cemented horizons and provides an acceptable sample support size. Geostatistical simulation methods were applied to establish the optimum sampling parameters required to estimate a mineral resource at an indicated level of confidence. The results show that a 5 m2 sample support size is adequate and that a 50 m 100 m sample configuration is optimal. Sample data obtained from the three methods confirms that the BG36 bucket auger tool combined with the parameters identified in this exercise produce the best results for diamond resource estimation.

Jan 1, 2009

The successful commissioning of the Cerro Verde project in Peru at the end of 2006 marked the culmination of the efforts of many in the industry over many years to have high pressure grinding roll technology recognized and accepted as a legitimate alternative to the conventional approach to large-scale hard rock comminution circuit design. Other hard-rock projects that have recently adopted HPGR include Freeport (Indonesia), Boddington (Australia) and Amplats Potgietersrus (South Africa). With the increasing acceptance of this technology, the need for technical presentations and articles exhorting the industry to adapt has diminished somewhat, and it is considered appropriate now to shift the emphasis to the provision of information for those considering embracing change. This article endeavours to answer frequently asked questions on the subject of high pressure grinding roll technology, with particular reference to its application in the hard rock minerals processing sector.

Jan 1, 2010

By B. P. Watson

Uniaxial tests performed on core from instrumented sites at Amandelbult 1 shaft, Impala 10 shaft and Union Section Spud shaft showed a nonlinear elastic relationship between applied load and induced deformation. This nonlinear behaviour does not appear to be dependent on borehole orientation but in the case of the Amandelbult and Union sites appears to have been influenced by the stress condition of the rock mass at the time of drilling. Cores drilled at these two sites under destressed conditions, such as over a stope, showed a linear elastic response to the applied load whereas most of the cores drilled under relatively high radial stresses were nonlinear. The Impala 10 shaft tests, however, all showed strong nonlinear behaviour irrespective of the stress condition of the rock mass at the time of drilling, although high stress conditions may have influenced the severity of the nonlinearity. A comparison between underground stress change measurements and an elastic model indicated that the rock mass became nonlinear when the virgin stress condition was relaxed to about 10 MPa. The cores for laboratory testing were retrieved from vertical boreholes drilled up from the centre of a stope and from horizontal boreholes drilled over pillars and stopes at about 600 m, 1 100 m and 1 400 m below surface for the three sites respectively. The k-ratios under virgin conditions were estimated from sockets, modelling and stress measurements to be 1.0, 1.3, and 0.5 for the Amandelbult, Impala and Union sites respectively. Of the three sites, therefore, Impala 10 shaft appears to have had the highest virgin stress state. Tests performed on similar rocks from shallower depths at Impala Platinum essentially showed a linear relationship between stress and strain. From the small Impala Platinum rock test database available to the project, it appears that the nonlinear elastic behaviour initiates at this mine from about 1 000 m below surface and seems to become progressively more nonlinear below this depth. In addition, the nonlinear elastic rocks are weaker, have a lower Young?s modulus and a higher Poisson?s ratio than their linear elastic equivalents. Interestingly the tangential Poisson?s ratios of the nonlinear elastic materials are often greater than 0.5 at 50% of the failure stress, suggesting an early failure initiation. The paper describes the microscope and modelling work done to determine the causes of the nonlinear behaviour and discusses some implications of the behaviour for deep-level mining.

Jan 1, 2009

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014