Search Documents

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By J. Du, V. Shukla, C. R. Kumar, U. Shivangi, D. P. Chakraborty

During the processing of iron ores, a large quantity of low-grade tailings containing abundant iron values in fine particle size range is produced. Due to the increasing demand in the high-grade ores for metallurgical operations and the stringent environmental conditions imposed on mining activity, it is essential to utilise the waste tailing pond slimes. Recovery of iron values from these tailing ponds not only enhances the life of the existing operating mines, but also enables achievement of a sustainable process. Iron ore tailing/slime (-150 μm) is produced after scrubbing and wet screening of a low-grade iron ore. Tailing beneficiation of iron ore has been addressed either by flotation or wet high intensity high gradient separation. The present paper aims to recover iron values from discarded slime containing assay ~56% Fe, ~6.5% SiO2, and ~7.0% Al2O3 from the Noamundi processing plant by using a high gradient magnetic separator (HGMS). In this process, tailings are effectively processed with a vertical pulsating high gradient magnetic separator to produce a relatively high-grade iron concentrate. The results of investigation indicate that this novel process is capable of producing an iron concentrate assaying ~ 60% Fe and ~3.25% alumina with a yield of ~55 % on weight basis and recover > 65 % iron bearing particles from the tailings. More importantly, the corresponding tailing contained ~45% Fe. It was concluded that this novel process may be effectively used to recover iron values from low-grade hematite tailings. Keywords: Iron ore slime, Fe recovery, HGMS, yield, Noamundi

Jan 1, 2020

By G. Mucsi, F. Kristály, R. Szabó

Kaolin is one of the most important ingredients in porcelain manufacturing. Its main phase is clay mineral containing aluminum hydrosilicate, namely kaolinite. Beside kaolinite it also contains quartz, illite and feldspars, which impair its applicability. Kaolin is a non-reactive material, but metakaolin can be produced by heat treatment (calcination) of kaolin, which is also used by the cement and concrete industry due to its latent hydraulic (pozzolanic) properties. Beside thermal activation, reactive materials can also be produced by mechanochemical activation in general. This paper deals with the mechanochemical activation of kaolin. The raw material was classified into various size fractions, then ground in a batch stirred media mill under varying circumstances (residence time, circumferential velocity). After grinding, the structural changes of the products were investigated by X-ray diffractometry (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). In addition, the particle size distribution of the ground material was determined by laser scattering. As a result of the grinding experiments and analytical measurements of the products, it can be clearly seen that reactivity of kaolin can be improved significantly by mechanical activation in a stirred media mill, but due to its high energy density the circumstances were optimised carefully to avoid aggregation. Keywords: Kaolin, grinding, stirred media mill, mechanical activation, material structure

Jan 1, 2020

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

Mr R. C. J. Goode (President) was in the Chair. There were also present one hundred and thirty-six Members, including Messrs R. J. Adamson, Dr J. M. Bereza, Messrs M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, G. W. Holl, Dr J. P. Hugo, Messrs C. J. Irving, P. Lambooy, Prof J. de V. Lambrechts, Mr D. G. Maxwell, Dr J. T. McIntyre, Prof R. P. Plewman, Messrs J. F. Reid, V. C. Robinson, H. Simon and P. W. J. van Rensburg (Council Members), G. Abdinor, C. B. Anderson, H. F. Allan, E. L. Atkinson, V. C. Barnes, J. F. Bennet, W. W. Bath, R. E. Barnes, C. L. Berrange, J. P. Buds, Dr W. Bleloch, Dr L. A. Bushell, Messrs D. L. Carson, D. D. Cornier, R. S. Cooke, R. R. M. Cousens, J. P. Coetzee, W. L. Cousens, J. Daniel, R. Daniel, D. G. Davies, S. K. de Kok, V. S. Dillon, B. S. Dykhouse, Dr H. G. Denkhaus, Dr R. S. J. du Toit, Messrs J. I. L. Edwards, R. C. Espley-Jones, J. C. Ferguson, D. T. Fourie, A. Frost, W. R. Flook, Dr N. P. Finkelstein, Messrs D. F. H. Grave, J. M. Gosnell, E. K. Gibson, R. W. Grout, E. W. Gray, J. S. Hay, F. G. Hill, H. N. Hepker, J. P. Hoffman, C. G. Hodges, D. M. Jamieson, Dr D. G. Krige, Dr N. P. Lategan, Messrs J. E. Laschinger, J. Levin, C. P. Linsell, J. O. Kempe, F. Q. P. Leiding, A. I. Lee, D. G. Malan, W. Malan, H. W. McCulloch, R. D. R. Munro, C. S. Macphail, Dr T. F. Muller, Dr A. J. Nel, Messrs S. C. Newman, G. G. Nicolson, G. Y. Nisbet, J. A. Papenfus, E. Pavitt, W. H. Pittie, P. C. Pirow, P. G. D. Pretorius, N. F. Peverett, R. P. Plaskett, M. P. Pearse, W. Pilkington, T. K. Prentice, Dr R. E. Robinson, Messrs R. B. Richardson, R. St. J. Rowland, R. J. Rouillard, F. O. Read, W. T. Ruhmer, D. Savile Davis, E. F. Statham, K. Smith, H. Simon, G. B. Stern, C. D. Storrar, Dr N. B. Strydom, Messrs J. H. Talbot, A. H. Taute, J. H. Taylor, G. W. Thiel, K. A. Tweedie, W. E. Vance, Dr H. J. van Eck, Messrs L. W. P. v. d. Bosch, P. A. von Wielligh, N. B. Vinson, S. J. Venning, W. M. Walker, D. T. Watt, Dr H. J. R. Way, W. T. L. Wayman, R. G. Williams, L. G. S. Wright and C. F. Ziervogel. Thirty Associate Members, including Messrs E. Collier, G. Douglas, D. H. Gray, H. G. Gericke, R. Hemp, N. M. Hayne, A. Hazell, P. M. Johnston, D. E. Love, Miss V. E. Marting, Messrs R. G. Matthews, P. Malpage, D. Nicolle, R. Pendreigh, J. J. Rosslee, R. W. Shearer, R. F. Taylor, G. C. Thompson and D. A. Viljoen. Three graduates, Messrs G. S. Giles, J. P. Hatfield and J. A. Jones. Five Affiliates, Messrs A. C. Collie, E. Collier, A. B. Cook, W. Jacobs and G. M. Thain. Two Students, Messrs C. J. Bircher and R. P. Henrard.

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012

By X. Chen, F. An, H. Chen, Z. Wang

The bottom drainage roadway plays a crucial role in preventing coal and gas outbursts by using underground gas drainage methods. Therefore, it is essential to select the ideal position of the bottom drainage roadway. In this paper use a combination of geological data and numerical simulation to study the ideal position of the bottom drainage roadway, we taking the gas drainage of the first workface of No. 3 coal seam in the Yuxi coal mine in China as an example. The geological study showed a limestone marker layer at an average vertical distance of 14 m from the first mining face. Using this marker layer, the bottom drainage roadway could be excavated without the risk of accidentally exposing the coal seam, and less crosscutting borehole drilling from the bottom drainage roadway would be required. Based on the needs of gas control, the layout of the bottom drainage roadway was selected as an external stagger type. Combined with the numerical simulation results, when located 20 m outside of the mining workface ‘footprint’ on the horizontal projection, the bottom drainage roadway was a sufficient distance from the stress concentration area during mining of workface 1301, which facilitated roadway maintenance. Furthermore, the length of the crosscutting boreholes is also relatively short, which reduces the amount and cost of drilling. The results of this study are expected to provide a reference for the selection of an ideal position of the bottom drainage roadway in field engineering.

May 2, 2022

By F. K. Crundwell

The rate of dissolution of sulphide minerals is frequently interpreted in terms of the passivating behaviour of a layer of material on the surface. This interpretation has driven research to identify and possibly remove this layer from the surface, and thus yield higher rates of dissolution. The identification of such layers has proved difficult, with different researchers claiming different compositions for possible layers. An alternative framework has been pursued by the author and co-workers, who have argued that the rate of dissolution is governed by the electronic structure of the minerals which give rise to their semiconducting properties. Researchers sceptical of this approach have argued that semiconducting properties are only important in highly pure substances. In this paper, we review the electronic and semiconducting properties and discuss how they impact dissolution behaviour. These properties affect their colour and dissolution properties even though the minerals are not high purity substances. Keywords: Dissolution, leaching, passivation, semiconductor, chalcopyrite

Jan 1, 2020

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By Y. Zhou, G. Chisakuta, P. Bwando, G. Mitshabu

A newly started copper hydrometallurgical plant was confronted with a manganese oxidation issue in electrowinning. This oxidation, in the absence of the amount of iron required to stabilise the electrolyte oxidation-reduction potential, is known to produce oxidants (MnO2, MnO4) that can cause accelerated degradation of the organic phase components in solvent extraction and corrosion of lead anodes in electrowinning. The overpotential required to build up the protection layer on new anodes causes an increased electrolyte potential that creates oxidized species in the electrowinning tankhouse, and these species come back to solventextraction plant with the recycled spent electrolyte. This paper discusses the impacts of manganese oxidants on the health of a plant organic phase. It also outlines the actions taken using iron scraps and sulfur dioxide to mitigate the problem that happened due to the lack of ferrous iron sulfate available on site, as recommended for better control.

Jan 1, 2023

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

By P. Pięta, A. Surowiak, T. Niedoba

In a flotation process of copper ore three factors were measured: copper grade in concentrate (β), copper grade in tailings (J) and recovery of copper in concentrate (e). The experiment was conducted by means of the Jameson cell. The factors influencing the quality of the process were particle size (d), time of separation (t), type of the collector (k) and dosage of the collector (s). The considered vector function was then [β(d, t, k, s), J(d, t, k, s), e(d, t, k, s)]. Optimisation achieved was based on determining the values of the adjustable factors (d, t, k, s). The goal was to obtain the highest possible values of functions β and e (maximum) and the lowest possible values of function J (minimum). To this purpose the taxonomic methods were applied. Keywords: Flotation, copper ore, lithology, flotation agents, particle size distribution, taxonomic methods

Jan 1, 2020

By J. C. N. Ashukem, F. Agyemang

One understudied area of environmental law is the socio-ecological impact of ownerless mines. This impact is particularly pronounced in resource-dependent regions like South Africa and Western Australia, creating significant rehabilitation challenges. This article hypothesises that effectively managed financial provision could be valuable for rehabilitating legacy mines. Using a qualitative, comparative methodology, the article analyses the financial provisions for mine rehabilitation in South Africa and Western Australia, focusing on statutory provisions, funding mechanisms, and rehabilitation outcomes. Key themes, such as context, measures, and outcomes, are explored to assess the effectiveness of each financial model. Purposive sampling is used to select case studies from both regions, and thematic analysis is applied to interpret the data. The analysis highlights the financial rehabilitation measures in both regions, providing a structured framework for ownerless mine rehabilitation. South Africa's approach, guided by the Mineral and Petroleum Resources Development Act (MPRDA) of 2002, depends on state budget allocations, leading to funding inconsistencies and slow rehabilitation progress. In contrast, Western Australia’s Mine Rehabilitation Fund Act (MRFA) of 2012 uses a levy-based system, ensuring continuous financial support for mine rehabilitation. South Africa's state-dependent model has led to delays in rehabilitating derelict and ownerless mines, while Western Australia’s funding model has facilitated steady progress. The article recommends that South Africa adopt a levy-based financial mechanism, strengthen legislative enforcement, improve financial oversight, and integrate proactive mine closure strategies to accelerate rehabilitation, reduce environmental hazards, and promote sustainable development in mining-affected communities.

Dec 15, 2025

By A. Golder, I. Roy

The Jayant opencast operation is one of the largest opencast coal mines in India. Prior to 2008 the mine experienced a number of dragline dump failures, which was a major hindrance in sustaining production. Northern Coalfields Limited (NCL) and the mine management engaged several design, research, and academic institutions to carry out dump slope stability studies, particularly of dragline dumps. BirlaInstitute of Technology prepared a report on the investigations in May 2009. In this paper we review the findings of the report and the measures taken to tackle the safety aspects of dragline dumps.

Jan 2, 2022

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By M. Izadi Yazdan-Abadi, S. H. Amiri, M. Ramezanizadeh, M. Bazmandeh

Iron ore concentrate is used as the fresh feed of pelletising plants. The green pellet properties depend on iron concentrate characteristics such as particle size distribution (PSD), specific surface area (Blaine value), iron grade, moisture content and grinding methods. The grinding methods affects particle size distribution and Blaine value. To find out the effects of grinding methods on pelletising process, green pellets were produced with concentrates that were reground by means of HPGR (high pressure grinding rolls) and ball mill. The Blaine values of ground concentrates in both types of milling were approximately 1400, 1600 and 1800 cm2/gr. The results of green pelletising tests on a pilot plant scale showed that at the same Blaine values, drop numbers of green pellets produced by ground concentrate inside HPGR were higher than the green pellets produced by ground concentrate inside a ball mill. Also, reground concentrates by means of HPGR, in comparison with ball mill, caused the production of green pellets, at higher wet and dry compression strengths. As a result, it was found that preparing the pelletising feed by means of HPGR led to more positive effects on the properties of green pellets. Keywords: Ball mill, HPGR, green pellet, drop number, wet and dry compression strengths

Jan 1, 2020

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By C. N. Eze, C. K. Ezeh, O. Nnabuife, N. M. Ugwoju, S. C. Enemuor, V. Okechukwu

In this study, the efficacy of Providencia vermicola KUBT-1 in the leaching and beneficiation of Agbaja iron ore was evaluated under varying conditions of temperature, ore particle size, and pH. Agbaja iron ore is a Nigerian low-grade ore containing about 43%–52% iron and a high amount of gangue materials, including phosphorus (1.4%–2.0%) and sulphur (0.12%). The study was organised in triplicate in shake flasks with 48 samples. One millilitre of washed cells of Providencia vermicola KUBT-1 suspended in normal saline at 0.5 McFarland standard (108 cells ml-1) was introduced into each flask containing 50 g of sterilised ore in 100 ml of bioleaching medium, and the samples incubated at room temperature for eight weeks. The levels of upgraded iron, mobilised sulphur, and phosphorus were determined by atomic absorption and ultraviolet spectrophotometric analyses, respectively. Results showed that a particle size of 0.8 mm was optimal for iron upgrading and sulphur mobilisation while 1.0 mm ore size was optimal for phosphorus mobilisation. Up to 89.60% of the iron was upgraded while phosphorus and sulphur were mobilised, leaving residual values of 0.223% and 0.02%, in the ore, respectively. The organism produced best beneficiation results at a pH of 2.5 and a temperature of 3ºC. Correlation analysis with the Pearson’s correlation model showed a positive correlation between iron upgrading and sulphur-phosphorus removal (r =1.000, and r =0.967), respectively. These results present Providencia vermicola KUBT-1 as a promising candidate for large scale leaching and beneficiation of Agbaja iron ore.

Dec 15, 2025