Search Documents

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.' The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978--September 30, 1979) under its Nine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's miners.

Jan 1, 1979

By H. J. Schroeder

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) accepted written comments until July 23, 1976, and held an informal hearing on August 24, 1976, to receive oral testimony regarding an economic and inflation impact statement prepared by OSHA on the proposed standard for occupational exposure to inorganic arsenic. These written and oral submissions were to be used in conjunction with information supplied at 1975 hearings to promulgate emission standards. An in-depth study for the Environmental Protection Agency (EPA) assembled and interpreted comprehensive information on arsenic and its compounds and the effects of these substances on people, animals, and plants.2 Another study for EPA assessed the role of arsenic and its compounds in the environment and in the economy of the United States and evaluated the need for and the projected effect of controlling its production, use, dissipation, and emission.3

Jan 1, 1978

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945

By W. D. Striffler

Land disturbed by surface mining in Colorado and other western states has increased substantially over the past several years and is likely to increase even more in the future. This study was initiated to provide basic information on hydrologic and erosional characteristics of regraded coal spoils in Colorado as an aid for planning future reclamation activities. Eleven of twenty-one surface mines licensed in Colorado were sampled during the summer of 1980 and 1981. Mines not sampled included mines which had not progressed to the point that reclamation had begun, and mines where operators denied permission to sample. All coal regions were sampled with the exception of the San Juan Coal Field. Physical and hydrologic characteristics of regraded coal spoils in Colorado were determined using standard field and laboratory procedures. Field sampling included characterization of sites (slope, vegetation density, proportion of surface rock, bare soil, etc.) and infiltration measurements using a l-meter square drop former raining on a 1/2 square meter rectangular plot frame. Core samples collected in the field were analyzed for saturated hydraulic conductivity, bulk density, organic matter, moisture retention and texture. The erosion potential of each site was determined using the Universal Soil Loss Equation (USLE). Results of the sampling indicate that infiltration rates vary widely both within and between sites. However, definite trends with respect to coal fields are apparent. For example, the Green River (Yampa) coal region had a wide range of sampled infiltration rates (1.2 to 5.1 cm/hr). However, most of the sites clustered towards the low end of the range. The North Park (Marr Strip) also was rated at the low end of the infiltration range (2.0 to 3.0 cm/hr). Average infiltration rates for the Canon City and Uinta Coal Regions were at the high end of the range (4.9 to 5.5 cm/hr). Multiple correlation analysis of infiltration rates vs. site characteristics showed that infiltration rates were most closely correlated with the depth of wetting, the amount of mulch cover, and site slope. The depth of wetting was highly correlated with the depth of the topsoil and the bulk density of the spoil. In general, the topsoil at all sites appeared to be highly permeable to water intake but once saturated, subsequent infiltration depended upon characteristics of the underlying spoil. Vegetation cover affected infiltration on individual mine sites but was not as pronounced as topsoil characteristics or mulch. Erodibility of topsoil and spoils, as determined by Wischmeier's "K" factor, ranged from 1.34 to 0.56 tonnes/ha. (topsoil) and 1.25 to 0.66 tonnes/ha. (spoils). Definite trends in erodibility are evident. The Green River (Yampa) Coal Region displayed consistently higher erodibilities (1.34 to 0.75 tonnes/ha.) than other coal fields (0.72 to 0.56 tonnes/ha). Lowest erodibilities were observed in the Uinta, North Park, and Raton Mesa Coal Regions (0.56 to 0.62 tonnes/ha). Erodibilities of underlying spoils showed similar trends as the topsoils. Erosion potential (the product of soil erodibility and rainfall erosivity) was detennined using calculated ?K? factors and rainfall erosivities (R) taken from Clyde (1976). Results show that the Delagua coal field, Raton Mesa Coal Region had the greatest erosion potential due to the high rainfall energies in the region, while the North Park and Uinta Coal Regions had the lowest potential erosion.

Jan 1, 1981

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By Joel N. Van Sant

An investigation was conducted to study possible sources of Utah refractory and structural clays that could be used for the manufacture of refractories and light or buff burning heavy-clay products. A field study was made and the clay samples tested to determine their firing characteristics. Results of the Bureau's work indicate many small noncommercial deposits of hypogenic clay occur in igneous rocks. Commercial hypogenic deposits are mostly halloysite clay developed by hydrothermal replacement of limestone. The high firing shrinkage of halloysite precludes its use as a refractory, however, halloysite produced at the Dragon Mine south of Eureka, is used for making oil catalysts. Clays and shales suitable for low heat duty refractory products are found in the Manning Canyon shale, in shales associated with coal bearing rocks, and in the Dakota formation. Some of the clays from the Dakota formation are also suitable for high-duty refractory products.

Jan 1, 1964

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

By W. L. Acherman

The Bureau of Mines found the chemical and galvanic corrosion behavior of the TZM and molybdenum-30 tungsten alloys to be generally equal or superior to that of unalloyed molybdenum in many aqueous solutions of acids, bases, and salts. Notable exceptions occurred in 1 [N] nitric acid, where both alloys corroded appreciably faster than molybdenum. In mercuric chloride solutions, the TZM alloy was susceptible to a type of crevice corrosion which was not due to differential aeration. The alloys were usually not adversely affected by con-tact with dissimilar metals in galvanic couple experiments, but the dissimilar metals sometimes corroded galvanically. Both alloys were resistant to substitute ocean water spray at 60° C.

Jan 1, 1968

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972