Search Documents

By D. R. Tesarik, F. M. Jones, J. B. Seymour, L. A. Martin, T. J. Williams

Determining backfill stress is an important part of evaluating mine safety, whether personnel are working in proximity to backfill or in other areas of the mine where backfill is an integral part of regional support. To assist in determining stress in backfill more accurately, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Placer Dome, Inc. (Turquoise Ridge Mine), Peabody Energy Co. (Foidel Creek Mine), and Hecla Mining Co. (Lucky Friday Mine) used temperature readings recorded by thermistors to correct for the influence of temperature on stress data. These thermistors were positioned in the stems of earth pressure cells installed in backfill. Corrections were then calculated and compared using four different methods: polynomial equations fit to temperature-versus-stress plots before the pressure cells were loaded by overburden, a factor provided by the manufacturer, a theoretically derived factor, and a linear correction factor based on information collected during periods when no mining was taking place. To evaluate the accuracy of these methods, corrected stresses were calculated using each method and results compared to cumulative stresses caused by blasting at one of the mines. Results indicated that only a small percentage of the temperature effect on stress was corrected using the factor from the manufacturer because that factor accounted for only the pressure transducer and not the entire instrument body. Stresses adjusted with a linear correction factor based on information collected during periods when no mining was taking place were the most accurate. Stresses recorded at two other mines were corrected using the theoretical method and the polynomial equations method; the two methods produced similar results. For some time intervals, the results were identical.

Jan 4, 2006

By Louis A. Panek

Tests of mine-roof models in a centrifuge show that the suspension effect due to bolting a horizontally bedded mine roof with frictionless surfaces of contact between beds depends principally on the number of bolted beds and their relative flexural rigidities, provided that sufficient bolt tension is exerted to prevent strata separations at the bolt locations. Strata separations tend to occur in the unbolted roof mainly because the beds have unequal thicknesses. "Suspension effect" refers to the transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds by roof bolts or by any other means. The factors investigated were number of beds in the bolted unit, bed thickness, modulus of elasticity of beds, length of bolts, spacing of bolts across and along the opening, bolt load, and intensity of roof load. The general principles of behavior of the bolted roof beds are explained by an approximate theory. Model test data are used to validate the theory and to obtain an expression for the "suspension efficiency". As the suspension effect actually observed in the models is smaller than that predicted by the approximate theory, the suspension efficiency in general is less than unity. Mathematical expressions are obtained for (1) the change in roof bending stress due to the suspension effect, which is needed for design of a roof-bolting system, (2) the change of roof deflection due to the suspension effect, which may be useful for evaluating the effectiveness of a roof-bolting system, and (3) the bolt load or pre-load that is required to achieve the desired reinforcing effect.

Jan 1, 1962

By K. O. Bennington

The thermodynamic properties of synthetic acmite, NaFe3+Si206, were determined by the Bureau of Mines. The enthalpy of formation was determined by hydrofluoric acid solution calorimetry. The values of the standard enthalpy of formation at 298.15 K, ?Hf°298.15, from the elements and from the oxides, ?H°298.15, are ?Hf°298.15 = -615.87 ±0.71 kcal/mole, ?H°298.15 (from oxides) = -32.08 ±0.53 kcal/mole. Various experimental data were combined with other data from the literature to calculate all the related thermodynamic properties in the range of 298 to 1,263 K. The standard Gibbs energy of formation is ?Gf°298.15 = -575.8 kcal/mole.

Jan 1, 1981

By Erik Sherer

Indonesia is poised to become a major player in the Pacific Rim thermal coal markets. Although the colonial Dutch developed numerous coal mines in the late 1800's for steamship bunkers and domestic fuel, Indonesia's coal industry has only recently begun to actively participate in the growing global marketplace. This export coal is primarily the result of the commercial development of coal mines in eastern Kalimantan by foreign contractors. From virtually no coal exports in the late 1980?s, Indonesia's coal industry has increased its exports to approximately 15 million metric tons (Mmt) in 1992. In 1992, Indonesia was the world?s sixth largest exporter of steam coal, By the year 2000, Indonesia projects that it will supply approximately 25 percent of the seaborne thermal coal requirements of the Pacific Rim countries. Although limited quantities of this coal may enter the European and U.S. markets, high qualities, low production casts, and favorable transportation rates will make Indonesian coals very competitive in the rapidly growing Pacific Rim markets. This study examines the Indonesian coal mining industry and compares it to the U.S. coal mining industry. This report is the sixth in a series of coal exporting country studies requested by the House Appropriations Committee. Previous studies examined the Colombian, Canadian, Australian, South African, Polish, and Venezuelan coal industries.

Jan 1, 1994

By H. F. Feldmann

This Bureau of Mines report presents a method for the computer solution of the equilibrium compositions of any complex, multiphase, chemical system for which appropriate thermodynamic data are available. The method describes in detail the computation of systems in which solid or liquid species can form by heterogeneous chemical reactions where these species do not occur in any equilibrium equations. Also described are the calculation of phases formed by condensation (pure or solutions) and the inclusion of other system restrictions such as electroneutrality. The method is being used to compute the equilibrium composition of mixtures of an electrically conductive plasma and a liquid slag phase arising from the high-temperature combustion of coal for magnetohydrodynamic power generation. These mixtures can contain up to 65 species including gases, liquids, free electrons, and ions.

Jan 1, 1969

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By J. R. Ruark

This report presents results of mining operations and of research and development work done during stage I of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Oil Shale Facilities. A brief description of the gas combustion process is given and the experimental program is discussed. Included in this discussion are (1) air-gas distributor development, (2) results of gas and shale distribution studies, and (3) effects of other process variable studies. The report concludes with a statistical evaluation of experimental results. Two appendixes present a chronological account of the experimental work and tabulations of data for all retorting runs conducted during stage I.

Jan 1, 1969

By E. L. Fosse, W. S. Wright

"INTRODUCTION Preliminary and detailed exploratory examinations of iron and copper ores on Prince of Wales Island have been conducted by the Bureau of Mines from early in 1942 until the end of 1944. Among these investigations was that of the Jumbo magnetite deposit, which was visited by Stephen P. Holt, an engineer of the Bureau of Mines, during a preliminary examination of the Copper Mountain and Jumbo properties September 15 to 18, 1943, During the months of June, July, and August 1944, a more detailed examination, which consisted essentially of mapping and sampling, was made by the authors working in conjunction with George C. Kennedy of the Geological Survey, Geological, topographical, and dip-needle contour maps were made of the area, and 97 channel samples were cut.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes sam¬ples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is made to R. D. Stewart, Territorial Commissioner of Mines and former general manager, and to Duncan Campbell, Ketchikan, Alaska, former mine superintendent of the Jumbo mine. Acknowledgment is also due to George C. Kennedy of the Federal Geological Survey for extending cooperative assistance in topographical mapping, dip-needle surveying, and geological study of the deposits. Further acknowledgment is made to C. Travis Anderson, chief, Rolla Division, Metallurgical Branch, and other members of that division for conducting beneficiation tests on Jumbo Basin ores."

Oct 1, 1946

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By Richard J. Mahany, Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission in metal/non-metal mines over a wide frequency range from 0.2 - 1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types include oil shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most important mining techniques. The results show that transmission at medium frequencies are optimum for wireless mine communications, in agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 8, 1981

By Richard F. Link

The principal procedures for the statistical analysis of gold assay and other trace-element data depend on applying either the normal frequency distribution or the lognormal frequency distribution. The consequences of applying both methods are examined through reference to example data from United States and South African gold mines. It is concluded that for estimation of average grades, except for certain data with a very high coefficient of variation (ratio of standard deviation to mean), use of the lognormal distribution is ordinarily undesirable because bias may be introduced and little efficiency can be gained. However, if biased average grades can be tolerated, as in the examination of data from surveys in exploration geochemistry, use of the log-normal distribution may be desirable. Various statistical analyses are detailed, and the tables presented to implement the analyses are more complete than those previously published.

Jan 1, 1971

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By D. B. Dow

"Natural gas-gasoline is made by collecting in the liquid state the condensable hydrocarbon vapors that exist in different natural gases in varying amounts. In the richer type of natural gas the gasoline is generally recovered by compression and cooling. If exceedingly high pressure or low temperature is used, there is dissolved in the gasoline a large amount of very volatile material, which evaporates rapidly at atmospheric temperature and pressure.In the leaner type of natural gas, the gasoline vapors are selectively absorbed from the permanent gases by passing the natural gas through an absorbing oil. The gasoline is recovered by distilling the saturated oil, and as compared with ""compression"" gasoline is of high Baume' gravity and low vapor pressure. Before a volatile gasoline can be transported in tank cars, it is necessary to decrease its volatility in order to lessen the risk of fire or explosion, as well as to prevent excessive evaporation in transit. This can be accomplished either by weathering the gasoline, or by blending it with a more stable material, naphtha being commonly used in the weathering process the more volatile portions of the gasoline are allowed to evaporate and the losses in volume are very large, therefore, blending is preferable, wherever possible.It is very difficult, however, to produce by blending, in gasoline plants, a motor fuel which is equal to straight-run refinery gasoline. In order to make a blended motor fuel of a grade equal to straight-run gasoline, only a small percentage of natural gas-gasoline can be blended with the naphtha, consequently it is customary to blend the gasoline with only enough naphtha to enable It to be shipped to an oil refinery when the material is again blended to form a finished motor fuel."

Sep 1, 1921

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980