Search Documents

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By G. W. Birge

Carbonizing properties of the principal coalbeds of Elk, Clarion, Jefferson, Clearfield, and Centre Counties, Pa,, are described in this Bureau of Mines report, Twenty-six samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, and Brookville beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AM) method, and yields of products and physical properties of cokes were determined. Expansion or contraction of the majority of the samples was measured in the Bureau of Mines sole-heated oven. Chemical analyses, agglutinating values, and free-swelling indexes are given for all samples. In this area the coals generally are characterized by high sulfur and moderately high ash content, and their suitability for metallurgical use would depend largely upon satisfactory cleaning. The samples from Elk, Clarion, and Jefferson Counties were high-volatile A bituminous In rank, whereas, most samples from Clearfield County and all those from Centre County were of medium-volatile rank. Coals from Clarion County had dry, mineral- matter-free fixed-carbon contents ranging from 56.5 to 60.3 percent and were weakly coking. With the exception of two samples which contained excessive ash, the medium-volatile coals of Clearfield and Centre Counties were strongly coking and, as indicated by sole-oven expansion results, would require blending with lower rank coal to avoid oven damage.

Jan 1, 1963

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

By N. S. Dalal, X. Shi

"Electron spin resonance measurements provide evidence for the formation of long-lived Cr(V) intermediates in the reduction of Cr(Vl) by glutathione redtuctase in the presence of NADPH and for the hydroxyl radical formation during the glutathione reductase catalyzed reduction of Cr(Vl). Hydrogen peroxide suppresses Cr(V) and enhances the formation of hydroxyl radicals. Thus Cr(V) intermediates catalyze generation of hydroxyl radicals from hydrogen peroxide through a Fenton-like reaction. Thus the mechanism of Cr(VI) toxicity might involve the interaction between macromolecules and the hydroxyl radicals.C(Vl) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals (1-3). In contrast, most Cr(III) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic (1,4). Cr(VI) and Cr(III) oxidation states are different in their metabolic pathways: Cr(VI) , ions are rapidly transported across cellular membrane (1,4,5), while Cr[III) moieties do not easily penetrate cells and are not oxidized by cellular constituents (!). Since it is known that the reduction of Cr(VI) ion is required for its reaction with DNA (1), the molecular mechanisms for the intracellular Cr(Vl) reduction has been the focus of current studies but the details are still not understood.Earlier studies on the mechanism of Cr(Vl) reduction include those on the reduction of Cr(VIJ by glutathione (GSH) .0,6-8), ascorbic acid (9), glucose (10), lactose (IO), galacturonic acid (11), microsome (12), and mitochondrial electron transport chain complexes (13). These studies have shown that the Cr(VI) reduction involves the formation of Cr(V)-containing species which are often considered to be the toxic form of chromium. Thus far, however, no information is· available on the subsequent fate of those biologically formed Cr(V) species, in particular employing well defined biochemical systems. In this context, we report here our investigations of the reduction of Cr(VI) by glutathione reductase (GSSG-R). This enzyme was selected because it is ubiquitously present in cellular systems and it has been postulated to be involved in the Cr(VI) reduction (14-17) but the underlying mechanism has not been clarified. We find that the reduction proces·s involves not only Cr(V) but also ·OH radicals. We further investigate the reactivity of Cr(V) and find that it catalyzes generation of OH radical from H2O 2 through a Fenton-like reaction. The role of ·OH in Cr(VI) carcinogenicity is suggested from this study."

Jan 1, 1989

By P. M. Sullivan

Galvanizers' sal skimmings have been treated by two methods of leaching in attempts to produce preflux solutions suitable for use in galvanizing operations. Both water-leaching and acid-leaching procedures are effective, except in severely exhausted skimmings when water-leaching becomes impractical. A preliminary analysis of the skimmings is not required. Solutions in the recommended concentration range can be produced conveniently by control of pH, specific gravity, and chlorine content. A technician would require only a short period of training to be able to perform the operations described.

Jan 1, 1958

By G. G. Campbell

The Bureau of Mines in cooperation with Quaker State Refining Corp. conducted two underground-combustion oil-recovery experiments in the Venango Second sandstone in the Reno pool, Foster-Rena-Oil City field, Sugar Creek Township) Venango County, Pa.) to determine the applicability of the process for reservoirs producing Pennsylvania-grade paraffin-base crude oil. Tests were terminated when analyses of produced gas showed that a self-sustaining combustion front did not exist. It was thought that insufficient fuel had been deposited in the formation. Laboratory retort tests made after the second field test was concluded showed that crude oil from the Reno area would deposit enough fuel to support combustion if air flux, temperature, and time were maintained within defined limits.

Jan 1, 1967

By Robert R. Perron

The U. S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 15 to 30 ampere fault to ground, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1975

By K. S. Gritton

The Bureau of Mines investigated the feasibility of numerlcally modeling the sorption of cobalt, a vulnerable strategic and critical metal, from spent copper leach solutions in a multiple-compartment ion-exchange (MCIX) column. Equilibrium resin loadings, cobalt-sorption kinetics, and resin-fluidization characteristics were determined in simple laboratory tests, and a numerical model was developed to predict cobalt extraction and the MCIX-column resin inventory based upon the test results. The model was implemented on a microcomputer to approximate the solution to the set of differential equations that govern model performance. Results compared very well with data from 12 pilot-scale MCIX-column experiments. The average difference between predicted and actual cobalt extractions was 3.2 pct; the maximum difference was 9.3 pet. The actual and predicted resin inventories differed by an average of 5.8 pet, and the maximum difference was 12.0 pct.

Jan 1, 1987

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983

By R. W. Van Dolah

An investigation was made of the distances over which sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) might be expected. Large-scale gap tests used two types of AN-FO donor charges in three sizes with AN, both at ambient and elevated temperatures, and AN-FO acceptor charges. Donor sizes were varied to test the validity of a scaling law commonly used in quantity distance tables. The up-and-down experimental design was chosen to determine the 50-percent initiation point efficiently. The acceptor charges were instrumented to indicate initiation and to determine detonation velocity. Other electronic techniques for measuring the rate of growth, stability of detonation, and detonation pressures were employed. Air shock and fragment velocities between charges were measured by electronic and photographic methods, and determination of side-on air-blast pressures and impulse duration were made for about half the shots. Separation distances between donor and acceptor were found to be larger than anticipated both for the AN and the AN-FO. With AN-FO acceptors and a 16-gage steel faced donor, one initiation occurred at a separation of 53 feet or nearly 16-charge diameters; with AN, initiation occurred at 4 to 5-1/2- charge diameters.

Jan 1, 1966

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992