Search Documents

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By Margaret R. Lickes

Mercury was produced originally at the Idaho Almaden mine from 1939 to 1942. When the ;.nine was shut down, more than 100,000 tons of ore, containing from 2.5 to 3 pounds of mercury per ton, was known to be adjacent to old workings but had been considered too low grade for commercial operation. Later, detailed, systematic exploration by Rare Metals Corporation of America increased and delimited enough minable reserves for further operation to be foreseen for several years. The average grade of the ore is estimated at slightly more than 3.5 pounds of mercury per ton. Open-pit mining and installation of the largest rotary kiln in the United States furnacing mercury ore have made possible profitable exploitation of these reserves (fig. 1). The bulk of the exploration was by percussion drilling, although some diamond drilling was done to check the results. When enough reserves were indicated to assure a successful operation, stripping and plant construction were started simultaneously. Figure 2 is a general view of the plant. The ore bodies, although irregular in size, shape, and grade and covered by essentially barren cap rock, are amenable to low-cost, trackless, open-pit mining. Development consists of stripping the overburden and removing, barren cap rock. Ore is being mined at approximately [5],000 tons per month and treated in a 175-ton-per-day furnacing plant.

Jan 1, 1957

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By Thomas O. Llewellyn

This U.S. Bureau of Mines (USBM) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material flow for the year 1989. This preliminary study contains information on cadmium and cadmium-bearing products in the United States. The data in this report were obtained from both published and/or unpublished sources of information. However, in order to estimate the fate of cadmium in each operation or application stage, some assumptions, judgments, and correlations were made by the USBM in an attempt to determine the material flows losses.

Jan 1, 1994

By K. A. Fowler, L. W. Higley

Steels with an alloying addition of depleted uranium were studied to develop successful melting , casting , and fabricating methods ; to obtain data on mechanical properties ; and to determine the effects of this alloying element . Uranium in amounts up to 1.5 percent was added to steel - base compositions containing approximately 0.5 percent carbon , 2 percent nickel , 0.25 to 2.0 percent silicon , and 0.75 percent manganese in both vacuum- melted and air -melted heats . Radiation levels were monitored for all operations . Bureau of Mines research at the Rolla Metallurgy Research Center showed that uranium additions did not increase tensile strength ; that hot - shortness occurred during forging above 1,090 ° C because of the presence of a low melting point constituent of a eutectic type ; and although a measurable amount of radioactive contamination resulted from processing , the quantity was never large enough to require the work area to be identified as a radiation area .

Jan 1, 1964

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By William R. Wayment, David E. Nicholson

The Bureau of Mines studied some physical properties of hydraulic backfills and their paramount characteristics , and made preliminary attempts to compact this type of material . The in- place density of hydraulic backfills affects the properties of strength , consolidation , and water percolation . Dense fills give better support than loose fills . In - place density properties themselves are affected by grain size , grain size distribution , and the particular conditions of sedimentation in a stope ( the amount of work the slurry water does to compact the material ) . Field sampling of in - place densities of fills presently used in four different mines and laboratory and underground compaction tests using a standard concrete vibrator show that the initial in - place density of the cohesionless fill material tested can be significantly increased by vibratory compaction .

Jan 1, 1964

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By Charles Prasky

The objective of this investigation by the Bureau of Mines was to determine the response to sulfatization of diverse low-grade manganiferous materials in the iron formation of the Cuyuna district. In line with this objective a bench-scale sulfatizing procedure was developed that was less expensive and more rapid than pilot-plant methods. Samples from the central and south- western parts of the North range were tested. Results of evaluating a total of 46 pelletized samples, originating in areas with an estimated potential resource of 94 million long tons with a manganese content of 7 percent, indicates that approximately 87 percent of the manganese may be recovered as a synthetic manganese ore. This is equivalent to more than 12 million long tons of a metallurgical-grade ore, containing 46 percent manganese. It is anticipated that a premium product, containing over 50 percent manganese, may be obtained by sulfatizing procedures. This report is part of a continuing investigation5 6 of Cuyuna iron range manganese deposits in Crow Wing County, Minn. Lewis and coworkers describe the manganiferous iron formation in the bedrock of the Cuyuna district and include a description of a high-temperature differential sulfatizing process for recovering a ferrograde manganese product. The low-grade manganiferous

Jan 1, 1961

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By J. B. Gayle

A half-ton experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial, slot-type ovens. The reasons for constructing an oven of this Size, the details of the design, and the operating characteristics of the oven have been given in previous publications.3/4 The present report deals with the reproducibility of test-oven data and the effects of variations in flue temperature on the physical properties of the cokes produced. Also included are the results of 2,400° carbonizing tests for several coals and coal blends not included in the earlier reports.

Jan 1, 1955

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By Bruce McDonald

This report contains the findings of a study to perform a task and skill analysis of roof-bolting operations, with respect to the operational training requirements and to prepare detailed recommendations for the operational training system. The extent of the problem was determined by visiting underground coal mines, interviewing training and safety personnel, observing and interviewing roof-bolter operators, and reviewing present training programs and facilities. In conjunction with the mine visits an extensive literature search was conducted with emphasis on training, mine safety, and accidents involving the roof-bolting operation and roof-bolter operators. A number of training programs and training devices were considered resulting in the development of a recommended training program including training devices to be used and establishing training objectives.

Jan 1, 1977

By Paul T. Allsman

The Salt River range vanadium deposits are situated 3 to 6 miles east and southeast of Afton, Lincoln County, Wyo. The vanadium occurs in a continuous bedded shale zone of the Phosphoria formation extending from the vicinity of Afton into southeastern Idaho. The Bureau of Mines explored several of these vanadiferous-shale deposits between December 1942 and December 1943 and conducted metallurgical tests on the ores. The areas investigated were west Swift Creek, the Dry Creek, and the Cottonwood Creek. The vanadiferous-shale beds have been folded sharply into a series of tightly compressed, eroded anticlines and synclines, which form the Salt River range. The vanadium occurs in a series of narrow shale or mudstone beds contained within the phosphatic-shale member of the Phosphoria formation. Exploration by the Bureau of Mines consisted of surface trenching and underground work over 18 miles of outcrop of vanadiferous shale with an average assay value of 0.866 percent V2O5.

Jan 1, 1949

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was done through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will be useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetime. This report is in two volumes: Volume 1 Technical Report Volume 2 Design, Inspection, and Maintenance Manual

Jan 1, 1977

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968