Search Documents

By Charles Prasky

This report describes and appraises recent progress in the development of a differential sulfatizing process for recovering a ferrograde manganese oxide from low-grade manganiferous ferruginous materials in the Cuyuna range. Individual process steps were carried out successfully using a 20-inch-diameter shaft for continuous countercurrent sulfatization of the manganese, a multiple-compartment rotary drum for leaching the water-soluble manganese sulfate, a submerged-combustion evaporator for the recovery of monohydrate crystals of manganese sulfate, and a shaft furnace for the thermal decomposition of sulfate crystals for production of a ferrograde manganese oxide and a sulfur dioxide gas suitable for sulfatization of fresh are. Of the two general kinds of Cuyuna manganiferous materials--the carbonate slates and the oxidized ores--only the slates were studied at pilot scale.

Jan 1, 1963

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By David E. Siskind

The Bureau of Mines has studied the fracturing and associated damage occurring in the vicinity of blastholes from five shots fired in the shale pillars in the White Pine copper mine, White Pine, Mich. Four types of explosives (AN-FO, commercial extra dynamite, ammonia gelatin dynamite, and a low-density, low-velocity permissible) were used. Cores were taken from the blast region and examined by ultrasonic and petrographic techniques. Pulse wave velocities were measured across the core diameters, and thin sections showing cracks and changes in lithology were examined in an attempt to establish zones of damage. Cores from the blast regions and areas near pillar free faces were found to have abnormally low pulse velocities. Petrographic study of the thin sections showed that the negative velocity anomalies were caused by cracks in the cores. Crushing and extensive fracturing prevented meaningful measurements on core fragments from the immediate blast vicinities. Compositional, changes and other rock nonuniformities, such as joints and preexisting fractures, tended to mask detailed damage differences among the four explosives; however, the two most energetic explosives (extra dynamite and ammonia gelatin dynamite) produced damage zones two to three times as large as the AN-FO and low-velocity permissible explosives.

Jan 1, 1973

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a simple and accurate method for calculating the viscosity of gas mixtures. Only the composition of the mixture and the molecular weights and viscosities of the pure components in the mixture are required. The momentum fraction of a mixture is calculated from the composition. The fluidity is calculated as a quadratic function of the momentum fractions. The efficiency factor for transfer of momentum in collisions between bodies of different masses is derived and used with one empirical constant. The viscosity is the reciprocal of the fluidity. Results of the method are compared with 752 reported viscosities for 40 dilute binary systems at temperatures from -78 to 276.9°C. Using this method the average absolute deviation is 1.29%, the root-mean-square deviation is 1.99%, and the average deviation is -0.84%.

Jan 1, 2010

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By H. A. Dierks

The work and costs involved in controlling three large fires in abandoned mines in the anthracite region of Pennsylvania are presented in detail. The work was done under authority of Public Law 89-4. Three basic control techniques were successfully employed by the Bureau of Mines: (1) forming underground fire-containing barriers by systematically flushing incombustible material into mine voids, (2) excavating an isolation trench around the fire area, and (3) complete excavation of hot and burning material in the fire area. When methods 2 and 3 were used, the excavations were subsequently back- filled with incombustible material. Preliminary location of fire perimeters by the standard use of patterned 6- and 8-inch-diameter boreholes is discussed. Investigations into air-borne infrared scanning, shallow subsurface thermal anomalies, and the use of helium to trace the movement of mine air currents are covered. Although they are costly and time consuming, boreholes have proven to be the most efficient means to date of obtaining necessary subsurface fire data. Infrared scanning was ineffective in delineating fires under more than 30 feet of cover. Helium-tracing was shown to have a good potential for determining possible hazards to adjacent residential areas from traveling mine fire gases.

Jan 1, 1971

By William M. Knuth

This study involved a review of bonding and bond release practices in the states of the Eastern and Midwestern Coal Provinces. Data was collected from regulatory authorities and site visits to document the bonding and release procedures in the states related to achieving successful reclamation. The regulations related to PL95-87 were reviewed. The analysis included suggested modified or new bond release criteria, a review of applicable bond release inspection techniques was prepared, a conceptual graduated bonding system and incentive procedures for reclamation of surface mine sites to alternative or higher land uses. A number of conclusions and recommendations for further research were included. A detailed bibliography and a glossary are included in the report.

Jan 1, 1978

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

By K. C. Dean

The Bureau of Mines, following passage of the Solid Waste Disposal Act of 1965, was authorized to conduct research on methods for utilizing, stabilizing, or reclaiming mineral wastes. This report summarizes laboratory research conducted by the Bureau and cooperative field studies made with the mineral industry to reduce the environmental impacts of air and water pollution deriving from mineral wastes. Utilization research showed that both dry-press and steam-cured building bricks and ceramic tile could be made from copper mill tailings and other discarded mineral wastes. Sponge iron was produced from steel mill and amination industry wastes, and valuable mineral products were extracted from such diverse sources as flue dusts and uranium tailings. Mineral wastes were combined with agricultural and/or sewage wastes to make artificial soils that have the potential of resolving several disposal problems by production of a useful commodity. Physical, chemical, and vegetative stabilization methods were evaluated, singly and in combination, for reclamation potential on copper, uranium, lead-zinc, and asbestos tailings. Suitable methods were developed in the laboratory for overcoming major adverse conditions of these wastes such as salinity, heavy metal toxicity, acidity, basicity, lack of nutrients and organics, and unstable surfaces. Field testing of these methods was performed on a variety of mineral wastes. Costs for the various stabilization and utilization-procedures developed were also determined.

Jan 1, 1986

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By A. M. Evans

Because of an urgent national need for manganese, the deposits in the Little Florida Mountains of Lune County N. Mex., were visited by O.H. Metzger, an engineer of the Bureau of Mines, on June 12 and 13, 1940, accompanied on the second day by S. G. Lasky, a geologist of the Federal Geological Survey. After this preliminary examination, it was recommended that exploratory work be done by the Bureau of Mines on several properties in the district. An exploratory project of trenching, sampling, and core drilling was started by the Bureau of Mines in September 1940 and completed in May 1941.2/ Work was done on three properties - the Luna mine, the American group of claims, and the Manganese Valley mine. The Little Florida manganese district is situated on the eastern slope of the Little Florida Mountains about 2 miles south of U. S. Highway 80-90, 12 to 14 miles southeast of Deming, Luna County, N. Mex. The principal claims comprise the Luna Manganese, American, and Manganese Valley groups.

Jan 1, 1949

By R. J. Leary

Significant improvements in surface conditions or mechanical properties of steels have been attributed by several investigators to ladle additions of small quantities of rare-earth metals or their oxides. To investigate systematically these effects in wrought and in cast plain carbon and alloy mechanical steels containing approximately 0.35 percent carbon, heats of four representative compositions were melted by the Bureau of Mines in a 4-ton open-hearth furnace. Each heat was cast into three sets of ingots to exemplify respectively, treatments with (1) rare-earth metals, (2) rare-earth metal oxides, and (3) an untreated set as a control. The development of melting, casting and rolling practices is described and discussed. Lance injection of oxygen shortly after melt raised the temperature of the metal immediately as much as 500° F., principally because mechanical agitation exposed the high-carbon metal to the flame and furnace root. An exceptional degree of superheat in the metal at the termination of the refining period was attributed to oxygen injection during the refining period. Bath temperatures higher than industrial practice were permitted by the all-basic furnace lining. Rates of carbon elimination as high as 0.036 percent carbon per minute were achieved by oxygen injections.

Jan 1, 1961

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By Everard Leland

This paper, describing the mining practices at the Pilares mine, Pilares de Nacozari, Sonora, Mexico, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts. At present (1930) practically all the mineral production from the Nacozari district is from the Pilares mine of the Moctezuma Copper Co., a subsidiary of the Phelps Dodge Corporation. The ore is mined for its copper but contains associated silver in small quantities.

Jan 1, 1930

By R. V. Ramani, P. M. T. White, D. Sutton

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. The project personnel express their thanks to Dr. Jay Politzer, The Pennsylvania State University Computer Center for providing the subroutine POLITZ and function IFIND, to Dr. Ray Masters, Department of Architectural Engineering, for permission for the use of the GRID program and to Dr. Lother Weyher of Bethlehem Steel Corporation for providing coal data.

Jan 1, 1974