Search Documents

By Ralph P. Carter

It is apparent that coal will play an increasingly important role in satisfying the nation's energy requirements for the remainder of this century. Both deep mining and surface mining will be practiced to develop known U.S. coal reserves, but until significant improvements in the productivity of deep mining emerge, surface mining is likely to be predominant. This report addresses the problems of coal extraction and surface mine reclamation in the 11-state Midwestern coal resource region, where surface stripping of high-sulfur, bituminous coal has been a well-developed industry for most of this century. Midwestern coal markets have declined in recent years. In part this is a result of widespread conversions to more convenient and (apparently) economical liquid and gaseous fuels, but the decline in Midwestern coal use is also attributable to the impact of current air pollution control regulations that prohibit emissions of sulfur oxides and particulate matter. A part of the regional demand for Midwestern coal has been transferred to the Northern Great Plains where extensive low-sulfur coal reserves are currently being developed.

Jan 1, 1974

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By H. E. Powell

The magnetic susceptibility, the geographical source, and associated minerals are given for 44 copper-, 26 lead-, and 19 zinc-bearing minerals. Of the 44 copper minerals/ all had a susceptibility of less than 15 X 10-6 cgs, and about 20 percent of them were diamagnetic. Of the 26 lead minerals, all had a susceptibility of less than 11 X 10-5 cgs, and almost half of them were diamagnetic. And, of the 19 zinc minerals, all except four had a susceptibility of less than 9 X 10-6 cgs, and about one-fourth of them were diamagnetic.

Jan 1, 1968

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the Purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of Procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By J. M. Kurtz

Ten Methane Monitoring Systems and Machine Control Circuits were examined and tested per the requirements in CFR Title 30, Parts 18 and 27, the Standard UL 913 and the document "Test Requirements For Instruments or Apparatus to be Considered for M.E.S.A. Intrinsically Safe Certification (Tentative)". The test results indicate that none of the products complied with all parts of all requirements as interpreted by Underwriters Laboratories Inc.

Jan 1, 1980

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

By Paul T. Alexander

After evaluating preceding studies and designs of lightweight supports, ESD selected the all-hydraulic and the hydromechanical concepts for detailed design and fabrication. Further analysis and testing showed that the all-hydraulic design was economically justified and met all the crucial engineering, manufacturing, and design criteria identified during the evaluation phase. Following Bureau of Mines approval of the detailed design, four all-hydraulic support models were fabricated. Once functional and structural testing was successfully completed, 40 additional units were constructed and distributed for in-mine testing. The units were very well-liked by all three demonstration mines. The wide- spread interest in supports for seam heights greater than 8 feet led to expansion of the design data package. ESD designed four basic models to cover the new height range, but no hardware has yet been fabricated for the new design.

Jan 1, 1982

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By Ronald B. Hollenbeck

The value of mineral production in Alabama continued to increase and reached a new high of $260 million, 3 percent above the previous high established in 1967. Record high values were reported for bentonite, crushed marble, lime, miscellaneous clay, portland cement, salt, sand and gravel, and scrap mica. The value of coal, total cement, petroleum, and stone accounted for 87 percent of the State&apos;s total value of mineral production. Alabama ranked second among the States in the production of bauxite and scrap mica and third in kaolin, masonry cement, and native asphalt.

Jan 1, 1970

By D. Pennington

Ground-water levels and subsidence have been monitored over a longwall panel of a deep coal mining operation located in western Pennsylvania. The monitoring network includes eleven ground-water monitoring wells completed to measure water level changes in separate shallow and deep aquifer zone-, and 50-foot surveyed subsidence stations parallel and perpendicular to the panel centerline. Monthly monitoring data were collected during the premining, mining, and postmining tine periods. Aquifer testing and borehole geophysical logging were conducted during premining, and post-mining conditions to document any changes in aquifer properties and ground-water flow patterns. Results indicate ground-water declines were located with respect to the mining face and mined longwall panel. Dewatering of the deep aquifer zone caused a significant water level decline in deep wells; however, the shallow aquifer zone was isolated fro major impacts by an aquitardal layer during, the, one-year period. Transmissivity data were greatly impacted by fracturing, in the highly anisotropic aquifer system. Borehole geophysical logging indicated changes in ground-water flow patterns and zones of increased fracturing from subsidence.

Jan 1, 1984

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet&apos;s assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U. S. Department of the Interior, to stimulate greater interest in safety in the mineral-extractive industries and to encourage the development of more effective accident-prevention programs. Since its beginning in 1925, thirty-four safety contests have been conducted. This publication reports results of the 11 annual contests for the period 1948-1958, inclusive. Mineral operations awarded the "Sentinels of Safety" trophy for the best safety record in their competitive group as well as those ranking second, third, fourth, and fifth are listed along with a summary of their achievements in preventing disabling injuries. In addition, this publication contains statistical information reflecting the disabling work-injury experience of all other mines and quarries enrolled in the annual contests. The injury statistics of these operations are arranged in the six groups of the competition and through 1955 are the only data on injury-severity at noncoal mineral operations published by the Bureau of Hines. Recognition of the National Safety Competition in promoting safety has increased steadily during its 34 years. The number of plants participating in these annual competitions increased from 210 in 1925, its first year, to a record of 675 in 1958. The expanding scope of the National Safety Competition indicates that more mines and quarries in the United States are enrolling 90 all available means to promote safety on the job will be used. Safety contests like this are generally recognized, in the field of safety promotion, as an effective way to arouse and hold the interest of employees and officials in accident-prevention programs. They tend to forge individual precautionary acts into group action centered on a common objective, such as winning the ?Sentinels of Safety? trophy.

Jan 1, 1960

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county&apos;s coal production, by beds, during 1948.

Jan 1, 1950

By Lu Li, Sara E. Wilson

Occupational exposure to whole body vibration has long been associated with increased incidence of low back pain and low back injuries1. A number of studies have investigated transmissibility of seat pan vibration 5, 6. While transmissibility has been well researched, the mechanism by which vibration may induce injury has not been thoroughly studied. Winter et al. identified increased reflex response delay after vibration exposure and speculated that muscular fatigue may be the cause of this increase9. However, a mechanism has yet to be demonstrated completely. A potential mechanism that may explain the increased risk is neuromotor habituation. Muscle spindle organs have been shown in the extremities to be sensitive to muscle and tendon vibration. Rapid length changes in muscle have been shown to result in kinesthetic illusions as the regular firing of the muscle spindles is interpreted as muscle lengthening4, 7. These illusions have also been demonstrated in the paraspinal musculature2. With removal of vibration, research in the extremities has demonstrated increased positioning errors, probably due to neuromotor habituation8. In this research, it has been hypothesized that neuromotor habituation after exposure to occupational vibration will increase positioning errors. It is further hypothesized that these errors can be shown to be linked to increased reflex response time. Such increased reflex response time could, in turn, decrease spinal stability and increase low back injury risk. Methods Both positioning error and sudden load response were measured before and after exposure to 20 minutes of 5 Hz, 0.223 m/s2 RMS seat pan vibration. Subjects were asked to sit on an unpadded seat without a backrest. Throughout the whole body vibration period, subjects were instructed to put their hands on a stable hand rest and feet on an adjustable stable footrest. The subjects were instructed to assume a comfortable and relax sitting posture for the duration of the exposure. Positioning error was measured using an active-active reposition sense protocol. Electromagnetic markers (Motionstar, Ascension Tech, Burlington, VT) were used to track trunk motion. With markers attached to the skin at the T10 vertebra, the S1 vertebra and manubrium, trunk flexion (the angle from vertical of the line connecting T10 and S1) and lumbar curvature (the difference in inclination of the T10 and S1 markers) were tracked. In the reposition sense protocol, subjects were asked to maintain an upright trunk flexion and to rotate their pelvis and lumbar curvature to assume a target lumbar curvature. In the protocol subjects completed training trials, where they were asked to match their lumbar curvature using a visual display, and assessment trials, where they were asked to reproduce the lumbar curvature from memory. After two initial training trials, training trials and assessment trials were alternated for a total of 3 assessment trials. Reposition error was defined as the absolute difference between the target lumbar curvature and the lumbar curvature the subject assumed during the assessment trials.

Jan 6, 2006

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970&apos;s to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008