Search Documents

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By Sam S. Taylor

"INTRODUCTION This report deals with a comparatively simple application of some of the engineering principles involved in the evaluation, installation, and operation of air- or gas-injection projects and well-clean-out and repair methods to increase the producing rates of oil wells in partly depleted pools during the war. The methods suggested for developing gas-injection projects take into consideration that in general no new wells will be drilled because of wartime restrictions of equipment and manpower and that only existing wells and second-hand machinery will be used. Because air will be employed as the injection medium in secondary-recovery operations where natural gas is scarce and expensive, the disadvantages and hazards accompanying, its use are discussed. Engineering techniques recognized as best modern practice are discussed in relation to the effect of simple air-injection development of properties on postwar operations and Probable ultimate recovery of oil. The report is an introduction to where, when, why, and how an air-injection project should be installed and operated; it is not intended to be an engineering manual for technical guidance in the selection, development, and operation of simulative methods of oil recovery.The report is intended mainly for these thousands of operators in the Appalachian region owning a few wells prodding small quantities or oil daily. Many such operators are anxious to increase their production rates by simulative means and to rehabilitate their wells so that they will produce more oil to help win the war but, in general, are unfamiliar with secondary-recovery operations and cannot afford to hire technical assistance."

Sep 1, 1944

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By James M. Spear

The U.S. Bureau of Mines conducted a mineral survey of the Domeland Addition (5207) and Woodpecker (5206) RARE II areas during the summer of 1979. These study areas were examined to determine the presence or absence of mineral resources and reserves and where possible, to estimate values. The study areas are 9 air mi northeast of Kernville, California, and encompass 47,400 acres of primarily granitic rocks of the Sierra Nevada batholith with some scattered exposures of older metasedimentary, volcanic, and metavolcanic rocks. These other rock units partially surround the exposed batholith in the Domeland Wilderness and consist mostly of late Paleozoic quartzites, mica schists, marbles, and meta-volcanics, Mesozoic quartz diorite and gabbro intrusives, and local Tertiary basalt and andesite flows.

Jan 1, 1981

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

The U.S. economy continued to expand during 1986, although at the slowest pace since 1982 when the current business expansion began. Real gross national product (GNP) grew about 2.6%, slightly below 1985 growth but significantly below that of 1984. The continuing expansion was fueled pre-dominantly by rising personal consumption expenditures as well as growing Government purchases of goods and services. Fixed investment, although positive, failed to grow at the rate of the overall economy. The trade deficit, which increased more than 30% over the record 1985 level, continued to depress economic growth despite significant declines in the price of petroleum and the value of the dollar. On a more positive note, domestic employment continued to grow--increasing over 2 million from the 1985 level--and inflation and interest rates declined. The unemployment rate dropped slightly to 7.0%. Of direct importance to the mineral-producing industries, expenditures for consumer and producer durables as well as investment in residential construction each grew faster than the overall economy, but investment in nonresidential structures fell more than 10% from the 1985 level. The level of real capital spending declined about 3% in 1986, following strong gains in 1985 and in 1984. Capital expenditures for new plant and equipment bottomed out in the second quarter and expanded in the third and fourth quarters. The decline in the first half of the year was partially attributed to uncertainty arising from the then-proposed tax bill. Also, there was little impetus for corporations to invest in new capacity since factories were operating at less than 80% of capacity during most of the year, in part because of continued competition from imports.

Jan 1, 1986

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications sys tem which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a relatively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurement s of ambient surf ace electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal- to-noise ratio at the surf ace. Numerous C .W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surf ace magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null is the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken Into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

Jan 1, 1974

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By E. L. Garton

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 3134, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and January and March, 1932, as published in Reports of Investigations 3140, 3147, 3150, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active Permissible list: Austin Red Diamond No. 1, L. F. Gel-Coalite W, L. F;" Austin Red Diamond No: 5. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.

Jan 1, 1932

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1986 was $405.2 million, a slight decrease from that of 1985. Alabama was second in the Nation in production of bauxite, crushed marble, and ferroalloys; third b fire clay; fifth in masonry cement and lime; sixth in total clays; and seventh in recovered sulfur. Alabama ranked 19th nationally in value of nonfuel minerals produced. Cement, clays, lime, sand and gravel, and stone were the major commodities produced.

Jan 1, 1988

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural- gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas, in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and In solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil- bearing horizons.

Jan 1, 1936