Search Documents

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By G. W. Jones

In cooperation with the Edison Electric Illuminating Co. of Boston, Mass., and the-Boston Consolidated Gas Co., the Bureau of Mines, United States Department of the Interior, has conducted a survey continuously since 1929 to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co.

Jan 1, 1942

By John A. Breslin

The Bureau of Mines measured respirable dust in coal mines by means of multiple dust samplers worn by persons moving about the mines. The measurements were made primarily to evaluate the effectiveness of certain dust-control techniques; however, for this report, the data have been analyzed to determine the precision of the personal dust-sampling measurements. A total of 68 sets of measurements were available from multiple personal samplers. The measured dust masses were less than 1.0 mg because the sampling times were short. The coefficient of variation calculated from these data was 18.5 pct, compared with coefficients of variation ranging from about 10 to 30 pct, which were calculated from the most precise and extensive data available for fixed-point dust measurements made in coal mines. From this comparison, it is concluded that dust samplers worn by personnel are as precise as fixed-point samplers in measuring respirabe coal dust; the wearing of the samplers by someone moving about a mine does not contribute significantly to the variation in measurements made with these instruments.

Jan 1, 1983

By Thomas M. Barczak

The U.S. Bureau of Mines has been conducting research to optimize the design and utilization of mine roof support systems. An objective of these efforts is to evaluate the mechanical and structural responses of various mine roof support systems under simulated load conditions in the Bureau's mine roof simulator. Underground studies are also made to evaluate the in situ behavior of support structures. The purpose of this report is to document practical applications for longwall face and gate road supports that have resulted from these studies. This report is not intended to be an all-inclusive manual on every aspect of support utilization, but it does provide a comprehensive assessment of practical considerations relating to the mechanical and structural behavior of these support systems. Forty-six recommendations are made to provide assistance to mine operators in the testing, selection, and utilization of longwall face and gate road supports. Many of these recommendations offer innovative solutions to everyday problems faced by mining personnel in the control of ground in longwall mining.

Jan 1, 1989

By David R. Jessey

Water pollution problems associated with surface metal/nonmetal mines throughout the United States were assessed. Three major problems were identified: acid mine drainage (AMD), toxic concentrations of heavy metals and excessive sedimentation. Several factors affect the type and amount of pollutants generated at a mine site. Among these are hydrologic regime, geology, mineralogy, topography, climate, size of the mineralized area and mining method. Nine surface mines situated in distinctly different settings were visited and their pollution problems studied. These mines were located in Morenci, Arizona; Hayden, Arizona; Sauharita, Arizona; Cobalt, Idaho; Spruce Pine, North Carolina; Iron Mountain, California; Butte, Montana; Fernwood, Idaho; and DeLamar, Idaho-Oregon. A detailed evaluation of the pollution problems at the Morenci mine indicated that a diversion system and treatment pint would be the most effective means of abatement for the existing water quality problems. Based on the study of the Morenci mine and three other porphyry copper mines with differing problems a water management plan was conceived for a new source copper mine. A companion Appendix Volume containing detailed reports on the mine site visits is on file at the US Bureau of Mines Spokane Research Center.

Jan 1, 1981

In the interest of safety in underground coal mining, the Bureau of Mines recommends: 1. That doors used to control ventilation (a) Shall be installed in pairs to form air locks, (b) Shall be self-closing, (c) Shall not have latches or other devices for holding them open, (d) Shall be constructed and maintained to prevent excessive air leakage through or around them, (e) Shall be fire resistant. 2. That wherever practicable the use of doors shall be limited to development openings. The Mine Safety Board is of the opinion that the best practice in coal-mine ventilation makes use of a split system employing overcasts or undercasts with doors limited as far as feasible to development openings. The distance between air-lock doors on haulageways should be sufficient to accommodate a trip or train of maximum length. Where auxiliary doors are installed to control ventilation during emergencies, they should be so placed that they can be utilized readily in case of damage to the air-lock doors.

Jan 1, 1938

By Robert Stefanko

This report, rather than attempting to replace previous annual reports, supplements, and more importantly, coordinates and summarizes the entire effort. Even with such restrictions, the report is voluminous and, therefore, a decision has been made to divide it into two parts. The first volume is basically narrative and includes tabular results and analyses. The second volume is in appendix form giving detailed information. Together, they permit a logical discussion of all aspects of the project (Volume I) without cumbersome distractions but, at the same time, provide all the details to permit others to evaluate and explain the results or develop similar research programs (Volume II). The aim of the original proposal was basically to develop instruments and techniques and then make measurements of suitable power parameters, ground fault currents and ground resistance beds. With such information available, it was possible to develop a meaningful simulator which would permit investigating electrical systems and components on paper without costly trial and error procedures in the third year, a cable splice testing program was added to the project. While there were the usual delays attendant in such original research, these objectives were achieved.

Jan 1, 1973

By Jr. Brinkley

For a theoretical description of power plants that derive their energy from the combustion of a fuel, it is necessary to solve, to an appropriate degree of precision, a hydrodynamic problem that requires for its solution a knowledge of the thermodynamic properties of the working fluid com-posed of the products of the combustion reaction. It is usually a good approximation to assume that the properties of the combustion gas are determined by the conditions of thermal equilibrium, and it is thus possible to employ the methods of Classical thermodynamics for their computation. The thermodynamic properties of fuel gases also are of considerable importance, as they form the basis for the design of appropriate means for their effective utilization. The specification of the operating conditions to produce a gas for use as an intermediate in a chemical process, such as the synthesis of liquid fuels, may be based upon a study of the variation of the composition of the synthesis gas with changes in the various process variables. Although there exists a large number of important scientific and technical applications of the data that can be obtained from the systematic determination of the thermodynamic properties of combustion gases, such application has been greatly handicapped by the extremely tedious and time-consuming computational methods required. The development of large-scale automatic computational equipment makes feasible the initiation of a systematic program for the determination of the thermodynamic properties of combustion gases and for the application of such data to specific problems of scientific and technical importance. As a part of its program of basic research in flame and combustion phenomena, the Explosives and Physical Sciences Division of the Bureau of Mines is engaged in such a program. The present communication is designed to introduce a series of reports presenting the results of this program.

Jan 1, 1951

This study was conducted to determine the feasibility of using large tractor dozers in land reclamation of strip-mined areas. The procedures used are patterned after engineering models developed for evaluation of military ground vehicles in cross-country operations. Tractor dozer manufacturers furnished information on capabilities of existing equipment and ideas on the practicability of using dozers larger than those currently available Generally, they believe that current dozers in the 500? to 700-horsepower range are about as large as can be built and remain economically feasible. However, one manufacturer has a wheeled dozer rated at 1200 horsepower, and another is testing a tracked dozer of about the same horse-power.

Jan 1, 1975

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1991. Most of the estimates are based on nine months data. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State mineral officer or Bureau field office specified in each State summary.

Jan 1, 1992

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By Llewellyn A. Rubin

Under Bureau of Mines Contract H0122007, Telcom, Inc., with the assistance of Fenix & Scisson, Inc., conducted a 17-month research and development project aimed at provid¬ing a field-test model of a guidance system for use with the Bureau of Mines Probe Drill. The Probe Drill is a part of the Bureau's Mine Rescue System developed under Contract H0101262. Volume I of this report is subdivided into seven sections. Volume II consists of a number of supporting appendices. In addition, there were delivered under the Contract, a number of other documents which are referenced in the text. Section 1 deals with essential contract information, Program Background, and a general system description. Section 2 covers the project chronology in brief. Section 3 is a digest of design considerations and implementation related to the requirements of the Contract. Section 4 is a description of the System, including illustrations of the hardware, and software. Section 5 is devoted to Operation and Maintenance. Para. 5.1 describes step-by-step field assembly and disassembly of the downhole unit. Para. 5.2 covers Operation. Para. 5.3 covers various aspects of maintenance from the lowest field echelon possible. Higher level maintenance must be accomplished in the laboratory, for the present field-test model. Para. 5.4 covers system calibration. Para. 5.5 covers detailed step-by-step operational sequences. Section 6 covers the results of the field testing, post-test evaluation, and recommendations. Essentially, we conclude that the present hardware (field-test model) has proven every aspect of system performance, but failed to provide reliable assurance of an operationally ready system. Telcom, therefore, recommends a three-phase continuing effort devised to provide the operationally-ready model of the system.

Jan 1, 1973

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By H. W. Busch

In the course of examinations by representatives of the Bureau of Mines of several compressed-air systems in which explosions had occurred, samples were obtained of the carbon deposits that are formed normally in various parts of the systems by decomposition of the compressor lubricating oil. Experimentation with these carbon deposits has demonstrated that they contain a "carbon-oxygen complex" similar to that formed on coal and on other carbonaceous materials and generally recognized as being the cause of spontaneous heating of coal. The exothermic properties exhibited by such a complex are considered significant in relation to the possible initiation of combustion reactions that may lead to explosions or formation of carbon monoxide in compressed-air systems. This report discusses the occurrence of explosions and formation of carbon monoxide in the use of compressed air and presents results of experimentation conducted with carbon deposits from air compressors.

Jan 1, 1949

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed b stone. Excess plant capacity has been chronic, and production is usually about 30 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1970 for glass feldspar is expected to be upward; less rapid in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979

By William A. Beck

"In 1912 bauxite was discovered in the Andersonville district, which lies in the 28th and 29th land districts of Georgia and comprises parts of Sumter, Macon, and Schley Counties. Mining was begun in May 1914 by the Republic Mining & Manufacturing Co. Considerable ore has been produced in this region since that time by individual interests and by the American Cyanamid & Chemical Corp., which acquired the property formerly owned by the Republic Co.The area was examined in the fall of 1941 by representatives of the Bureau of Mines and the Geological Survey, after which a prospecting program was begun by the Bureau. Drilling was started on December 26, 1941, and continued until November 18, 1943. A total of 1,192 holes was drilled in the district, and 3,679 samples were taken and analyzed.Mineral exploration agreements were signed by 146 property owners covering 42,128 acres. Holes were drilled on 121 of these properties, which have a total area of 38,778 acres.Drilling under this project disclosed several new deposits, of which four have been completely delimited. Previous prospecting in this area by mining companies did not find bauxite, as it lies under heavy overburden. Work by the Bureau indicates 14,412,000 long tons of ore containing 30 percent or more alumina. The total tonnage is divided as follows:Georgia State Highway Routes 26 and 4-9 traverse the district. The Central of Georgia Railroad passes through the center of the entire district (see fig. 1).The project was initiated by J. R. Thoenen, supervising engineer, Non-metals Mining Section, Mining Division, Bureau of Mines. It was under his general supervision until July 1942, after which it was under the general supervision of E. J. Lintner and Rowe McCrae, district engineers for Georgia, South Carolina, and Flordia, respectively.John C. Feeley, Jr., was project engineer from December 1941 to April 1942. Other engineers who assisted in the work on the project are R. E. Babcock, T. M. Romslo, Don M. Coulter, and Walter T. Lewiecki.Acknowledgment is due the metallurgical staffs at College Park, Md., and Tuscaloosa, Ala., for analyses of samples and beneficiation tests.Acknowledgment is also expressed to Alfred D. Zapp, M. W. Harris, Elmer Kneedler,and Parke D. Snavely, of the United States Geological Survey, for their aid, data, and maps.Bauxite was discovered in the Andersonville district in 1912 on lot 187 of the 28th land district, in Sumter County. This lot is situated about 1.5 miles west of the Flint River, on the south slope of the valley of Sweetwater Creek. Mining was started in May 1914 by the Republic Mining & Manufacturing Co. This and adjacent properties were acquired in 1930 by the American Cyanamid & Chemical Corp., which has been operating there since."

Dec 1, 1949

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941