Search Documents

By J. Drzymala, K. L. Wolters, T. Chmielewski, T. D. Wheelock, D. H. Birlingmair

Microflotation tests were conducted with a modified Hallimond tube equipped with a fritted glass disk and magnetic stirrer to determine whether the results would support an equation that predicts a linear relationship between particle size and the reciprocal of particle density in water for a specified flotation recovery in a given time. Data obtained with the tube for either hydrophilic or hydrophobic solids fit the equation satisfactorily. It was also shown that the natural flotability of molybdenite is somewhat less than that of elemental sulphur and that sodium dithionite is a good depressant for sulphurised pyrite. In addition, it was found that the untreated pyrite and galena used in the study were hydrophilic and did not float by particle-bubble attachment.

Jan 4, 1992

By I. R. Stevenson, J. G. Dunn, T. N. Smith, L. C. Mackey

An experimental flash reactor has been developed to simulate the operation of an industrial flash-smelter reaction shaft. Four concentrate materials of differing mineralogical compositions were characterised and then oxidised in the reaction shaft. The products were examined by chemical analysis to determine the extent of oxidation and by electron-probe microanalysis to determine the fate of individual particles. This programme of work enabled the influence of mineralogical composition and particle size on the extent of oxidation to be assessed

Jul 1, 1991

By J. H. E. Jeffes, K. T. Jacob

Solid oxide galvanic cells, of the type: Pt,Ni-NiO | Solid electrolyte | O(metal),Cermet,Pt, were used to measure the activity coefficient of oxygen in liquid Cu at 1 100 and 1 300°C and in Pb at 1 100°C. Similar cells were used to study the activity coefficient of oxygen in the whole range of Cu + Pb alloys at 1 100°C and in Pb-rich alloys at 900 and 750°C. The results obtained are discussed in terms of proposed solution models. An equation based on the formation of 'species' of the form M(2)O in solutions of oxygen in binary alloys is shown to fit the experimental data

Dec 1, 1971

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

By C R. Ferrari

Residual subsidence is generally accepted as being about 5% of the total subsidence occurring within 12 months of all mining finishing. This paper looks at five case studies from different parts of the country, in various mining settings within a depth range of 430m to 760m. From a single seam single panel working to working the eleventh seam, all are within the concealed coalfield, similar to today's mining. The monitoring of subsidence continued for many years once the mining had finished and the results obtained are at considerable variance from the accepted norm. Subsidence has been found to carry on for up to eleven years after mining has ended, within a range of 8% to 45% of total subsidence. A highly significant factor was that subsidence, as a whole, was generally much more than predicted. The residual subsidence aspect has to he viewed in this context and in order to debate the subject at length, the causes of residual subsidence have to be balanced against the apparent inability to accurately predict subsidence. The results from the case studies were similar, even though the mining settings differed considerably. Subsidence of around 10% to 20% continued for several years after mining had ceased.

Jan 7, 1997

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

Discussion of the paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, with Mr. John Gregory, President, in the chair, included contributions by Gregory J., Cadman J., Hartley J.W., Wain E.B. and Henshaw A.M., followed by the author's reply

Dec 1, 1916

By A. D. Read

Selective flocculation was investigated as a possible method of recovering values from mineral slimes which are too finely divided to be treated by conventional mineral processing methods. It has proved possible to flocculate selectively either haematite or a silicate from a stably dispersed mixture by varying the anionic character of the high-molecular-weight, partially hydrolysed polyacrylamide employed. Different separation methods have been developed for hard and soft water media. Electrokinetic and infrared techniques have been employed to elucidate the mechanism whereby selectivity has been attained in the different cases. The following influences on the various selective flocculation parameters have been investigated: (a) the level of the different reagent additions and (b) the shear conditions during and after flocculant addition. A feature of the particular system studied was the high solids content at which it was possible to achieve good selectivity. Probable reasons for this are advanced, and the possibilities and potentialities of the process are discussed.

Dec 1, 1971

By I. Garba

The Bin Yauri deposit in the Zuru schist belt of northwestern Nigeria is a vein-type quartz-sulphide-carbonate gold mineralisation hosted by a brittle fault zone. The occurrence of the mineralisation in a contact zone of a Pan-African granitoid was believed to be sufficient evidence of deposition from magmatic fluids. However, studies may now indicate a metamorphic source for the mineralising fluids. A study of rare earth element geochemsitry was used to investigate the nature of the fluid-rock processes involved and identify the sources of the auriferous mineralising fluids.

Jan 12, 1992

By R. E. T. Hill

"A laboratory study was undertaken to determine the condensed equilibrium phase relations at 600°C in that portion of the quaternary Fe-Ni-Cu-S system which lies in the neighbourhood of the monosulphide solid solution (MSS). The study sought to determine to w hat extent copper affects the temperatures of stability and compositions of iron-nickel sulphides in bulk compositions similar to those of massive Fe-Ni-Cu ores. Experimental data, including stable phase assemblages and phase compositions, are presented.In the quaternary system at 600°C MSS forms stable phase assemblages with pentlandite, chalcopyrite solid solution, pyrite and vaesite. Over the range of bulk compositions displayed by natural ores copper as well as metal/sulphur ratio have a significant effect on the thermal stability of pyrite and pentlandite. Errors therefore accompany the widespread practice of ignoring copper or chalcopyrite when the mineralogical and compositional changes that have accompanied the initial cooling of primary magmatic sulphides or their subsequent homogenization during isochemical metamorphism are being deciphered. These errors are most significant for ores the bulk compositions of which lie tow ard the sulphur-deficient side of the cupriferous MSS. Temperatures as much as 300°C above the copper-absent value are possible for the interpreted upper stability limits of pentlandite in these ores.The experimental data show that up to 2.0 at% copper can occur in pentlandite stable at 600°C in a bulk composition equivalent to natural magmatic ores. This is equivalent to nearly 10 vol% chalcopyrite. Pentlandite contains more copper than coexisting MSS and the copper content of both phases increases with increasing iron."

Jan 1, 1984

By Ruddle R. W.

Magnetite occurs in the reverberatory furnaces, blast furnace and converter (a) as the result of its presence in the materials charged, and (b) as the result of oxidation of the FeS in the charge in the absence of sufficient SiO2 to slag the FeO as it is produced and thus prevent its subsequent further oxidation. Magnetite is reduced by FeS according to FeS+3Fe3O4=10FeO+SO2 and similar reactions. This reaction is markedly affected by temperature and does not proceed to any important extent below about 1200°C. To ensure comparative freedom from magnetite it is therefore necessary to raise the temperature of the furnace to the highest practicable figure and to use plenty of siliceous flux. Since the maximum operating temperature is likely to be limited by the resistance of the refractories to attack by the slag, investigation of the factors affecting this attack should be helpful. It is reasonable to suppose that the formation of magnetite might be minimized by ensuring intimate admixture of matte and slag during conversion so that silica is readily available for combination with ferrous oxide as the latter is formed. The literature gives no clue to the importance of this factor and some experimental work on this aspect might be fruitful

Jan 1, 1953

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

By D. G. Skinner, J. H. Griffiths, F. T. Williams, A. G. Withers

"The absence of homogeneity, in dust-clouds underground indicates the use of a method in which the volume of air sampled is an appreciable proportion of the total volume under consideration. Of the available methods, only the impinger and gravimetric techniques seem to comply with this requirement. In practice, greater efficiency of collection of the smaller particles is possible by the use of a gravimetric filter than with the impinger. For this reason if, as seems desirable, a standard method of sampling be sought, the adoption of a gravimetric technique is to be recommended.Provided that the amount of dust collected is reasonably large, the paper filter would seem to be preferable to the solid crystal type of filter on account of its greater convenience in use.Alternative methods of sampling are desirable to cover the wide range of practical conditions."

Jan 1, 1947

By R. Phillips

The low concentration of diamond in workable deposits requires very large samples for grade estimation, and results, even then, may be erratic and difficult to interpret. Although the Poisson probability distribution cannot accurately describe the occurrence of diamond, it is suggested that it gives a better estimate of grade than conventional methods, even from single samples. Examples illustrate the simple calculation required.

Dec 1, 1971

By J. H. E. Jeffes, K. T. Jacob

The activity coefficients of oxygen in liquid Pb-Sn alloys have been measured between 550 and 1100°C by use of solid oxide galvanic cells: Pt, Ni-NiO | Zr02 Solid electrolyte | O (Pb + Sn), Cermet, Pt; and Pt, Fe-FeO | Zr02 Solid electrolyte | 0(Pb + Sn), Cermet, Pt. Alcock and Richardson's quasi-chemical equation, with the coordination number of atoms set to 2, is found to predict successfully the activity coefficients of oxygen in these alloys. The relative partial molar enthalpy and entropy of oxygen at 1 atom per cent in the alloys have been calculated from the variation of the activity coefficient with temperature. The addition of Sn to an unsaturated solution of O in Pb is shown to decrease significantly both the partial molar enthalpy and entropy of O. As the measurements were restricted to a narrow range between 750 and 1100°C in Pb-rich alloys, however, the pronounced variation of the partial molar enthalpy of O with temperature at constant alloy composition predicted by the quasi-chemical model could not be verified.

Dec 1, 1971

By L. J. Barnes, R. O. Koch, J. H. Versteegh, P. J. H. Scheeren, F. J. Janssen

Following two years of laboratory research with bench scale reactors, a 9 m3 experimental process demonstration reactor was installed at Budelco's zinc refinery to treat their underlying groundwater. A 600-fold scale-up was successfully achieved. It has demonstrated that this anaerobic microbial process can remove a wide range of heavy metals and sulphate to the required levels. Extended operation of the demonstration unit has shown that the process is robust, can withstand wide variations in feed composition, rapidly recovers from operational upsets and is easy to start up and shut down. The metal sludge produced can be processed in a metal refinery to recover both metals and sulphur.

Jan 12, 1992

By G. B. Hooper, G. A. Ferguson

The technical capabilities and user-friendliness of the major computer-aided mining design software systems are reviewed. Recent experiences with three systems are outlined to indicate the practical problems that arise. The examples were: Microlynx software from Lynx Geosystems at the Great Dyke platinum mine in Zimbabwe; Lynx software from Lynx Geosystems at a copper mine in central Africa; and PC-MINE software from Gemcom Services at an open-pit gold project in Western Australia. Difficulties in the use of mining design software has led to an alternative approach. Falconbridge, Canada, has developed an integrated mine-planning system on a CAD platform that encompasses ore reserve estimation, stope design, development layout and survey control. Future directions of computer-aided mining design using this basis are discussed. A major advantage of using mainstream software packages, such as spreadsheets, databases and CAD programs, is that most engineers and geologists are experienced in handling such systems in the normal course of their work.

Jan 12, 1992

By R. Patel, J. Ephraim

The production of titanium dioxide (TiO2) from its minerals such as ilmenite is challenging, and subsequent isolation of titanium from TiO2 is even more difficult because of the metal-oxygen bond strength. Currently, titanium sponge is mainly produced via the Kroll process, which is energy intensive and generates large quantities of waste. A number of international research groups have come up with technologies for the production of titanium metal. However, none of them have been commercialised, because of engineering or economic issues. The team at Bradford have confirmed that ultra-pure titanium powders can be separated from TiO2 powder through metallothermic reduction and are working to scale up the process.

May 1, 2015

By A. Paulin, A. W. D. Hills

The work has shown that packed-bed behaviour can be predicted from the results of single-particle experiments, total reaction times being predicted somewhat more accurately than gas and solid temperatures and gas compositions. A small laboratory packed-bed reactor was built and used to study the decomposition of beds of specially prepared CaCO3 spheres, steps being taken to minimise the effects exerted by the walls of the bed on processes occurring within the bed. Gas and solid temperatures and gas compositions were measured at various points in the bed and compared with theoretical predictions based on kinetic data determined in previous single-particle experiments. The measured solid temperatures and total reaction times agreed remarkably well with the values predicted theoretically. Gas and solid temperatures measured after the reaction had finished at any point in the bed did not agree with the theory. This was because solid temperatures in the bed rose very rapidly once the reaction was completed and the walls of the bed could not be heated at a sufficient rate for their temperatures to rise as rapidly; thus some loss of heat from the bed to the walls was inevitable, and this could not be accounted for in the theory. In addition, the theory did not allow for the conduction of heat within the bed, and this resulted in some further slight discrepancy between the measured and predicted values, particularly after the reaction was completed. Gas compositions measured in the bed were rather scattered, but, even so, they agreed moderately well with the predictions of the theory.

Dec 1, 1971

By A. B. Holland-Batt

Two graphical techniques which are commonly used to assess batch separations are analysed in terms of reaction kinetics to provide a more powerful method of evaluation. An alternative and more general approach, based on the selection and application of suitable efficiency criteria, is also presented. The method proposed distinguishes between selection and collection efficiency in flotation and can be used to estimate the degree of liberation in the feed. Two examples are given: table concentration of monazite and ilmenite from a beach sand, and flotation of a pyrite-haematite ore

Dec 1, 1971