Search Documents

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By L Besra, A. R. Prasad, B. P. Singh

The role of surface-chemical phenomena and the physical processes that participate in the dewatering of a suspension of alumina trihydrate were subjected to a systematic investigation, which has increased understanding of the influence of surface tension, contact angle and adsorption in the process. The residual moisture content of the cake can be reduced significantly through the use of surface-active agents in slurry pretreatment or as wash-water additives. The effectiveness of a particular surfactant is hard to predict from any single parameter, but is dependent on its ability to reduce surface tension and possibly to modify the solid-liquid contact angle. If scaled up to industrial operation of the dewatering step of the Bayer process in India, the use of these chemical additives could substantially improve its process economics, reducing the fuel costs for thermal drying by a much as Rs 50/t

Jun 21, 1905

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By R. K. Rath

Adsorption, electrokinetic and flotation studies were carried out. The maximum density of adsorption of guar gum was obtained at pH 7.5 on sphalerite and at pH 11.5 on galena. Flotation recovery of sphalerite was reduced only marginally by the presence of guar gum in the pH range investigated, whereas recovery of galena was reduced to about 20% at pH 12. Differential flotation tests on binary mixtures indicated that 10 ppm of guar gum can depress galena and separate it from sphalerite at around pH 12.1. Co-precipitation tests confirmed the formation of a metal ion-guar gum complex in the bulk solution, suggesting that this is the precursor to adsorption. The adsorption isotherms for both minerals followed Langmuirian behaviour, but adsorption of guar gum on galena was significantly higher than on sphalerite and dissolution tests indicated that the concentration of Pb ions released from galena was an order of magnitude greater than that of Zn ions dissolved from sphalerite

Jun 21, 1905

By H. L. Paterson, R. R. Keays, M. J. Donaldson, D. J. Boyack, M. F. Smith, J. J. Gresham

"Albite-rich sedimentary rocks that contain abundant Fe sulphides occur in the lower portion of the ultramafic sequence at Kambalda and their broadly antipathetic relationship to most of the nickel orebodies is well documented. These sediments generally contain less than 0.1% Ni, but nickeliferous equivalents with 0.3 to >6% Ni occur locally in close spatial association with more typical volcanic peridotite-associated massive, matrix and disseminated ores. Nickeliferous sediments have been mined at several locations at Kambalda but, collectively, they constitute less than 2% of the total Kambalda nickel reserve. The nickeliferous sediments occur both on the ultramafic-footwall basalt contact and within the lower part of the ultramafic sequence, and are usually less than 5 m thick. They are commonly finely laminated rocks with a cherty appearance, composed essentially of layers of albite+quartz±amphibole, alternating with pyrrhotite+pentlandite±pyrite layers. Some contain a minor amount of carbon. The sediments are only of ore grade (> 1% Ni) immediately adjacent to massive Fe-Ni-Cu sulphides, which are interpreted as normal magmatic ores on the basis of geochemistry and the presence of distinctive ferrochromites. The nickel content of the sediments decreases to background levels (<0.1%) within about 20 m of the massive sulphides. In most locations the massive sulphides clearly have been emplaced tectonically within or adjacent to the sediments, which are commonly highly deformed. Typical nickeliferous sediments contain about 1% Ni, 0.1% Cu, 0.1% Zn, 400 ppb Pd, <0.2 ppb Ir and 10-200 ppb Au. They have lower Ni/Cu (average 10), higher S/Ni (average 6) and higher S/Se (average 11 200) than associated massive sulphides (average 40, 4.8 and 7400, respectively). The Pd/Ir ratio of the nickeliferous sediments (typically > 1000) contrasts markedly with that of associated massive sulphides (average ca 16).The high Pd/Ir values are similar to those which have been reported for hydrothermal Fe-Ni sulphides and barren sulphidic sediments of probable volcanic exhalative origin. They preclude a direct magmatic origin for the sulphides in the nickeliferous sediments, though S/Se and S isotope data indicate a magmatic source for the sulphur. The restriction of nickeliferous sediments to within about 20 m of normal magmatic sulphides and the lack of a widespread Ni dispersion halo suggest local redistribution of originally magmatic Ni. This probably occurred by diffusion and hydrothermal mobilization during deformation and amphibolite-facies metamorphism. Although not totally ruled out, a volcanic exhalative origin for the Ni seems unlikely."

Jan 1, 1984

By G. Adachi, K. Machida, T. Ozaki, K. Murase

The chlorination rate with CCl4 was unexpectedly slower than carbochlorination using chlorine under the same reaction conditions. Chlorination with CCl4 was topochemical and the amount of monazite reacted after different periods suggested that the kinetic control step was the reaction between CCl4 and the monazite core at the interface. The kinetic order of the reaction was 0.5. The presence of a complex former, AlCl3, promoted the chemical vapour transport of rare-earth chlorides as complexes

Jun 18, 1905

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

Studies were carried out to examine the effect of introducing varying levels of a pisolitic limonite (Yandi) into an Australian iron ore blend. Compared with other ores in the blend Yandi is more porous. This structure is found to have a considerable effect on the sintering behaviour of the blends. Pilot-scale sintering studies and plant trials showed that sinter plant productivity, sinter reducibility and the low-temperature reduction degradation index altered significantly when the level of Yandi in the ore blend exceeded 15 wt%. The improvement in the reducibility is thought to be a direct result of increased porosity in the sinter and the presence of highly reducible pseudo-relict haematite. Plant trials have also shown that operational changes could be made to the sinter plant to avoid potential deterioration of productivity

Dec 1, 1991

By L. T. Matthews, C. E. Loo, R. P. Williams

The behaviour of iron ores and fluxes in the high temperature zone of a sintering bed is extremely complex. Following a review of current knowledge, an attempt is made to define relevant terminology to describe the processes that occur in this part of the bed. A deformation temperature is used to quantify the initial formation of melt, which is produced predominantly by reactions between fine particles in the sinter mix. The subsequent assimilation of larger particles is considered to depend on the reactivity of the melt and the assimilation resistance of these particles. Novel laboratory experimental techniques are used to quantify these parameters. Results demonstrate that the properties of the raw materials used have an extremely important influence on the initial processes of melt formation and assimilation and also on the nature of the sintering reactions and sinter-bonding phases.

Jan 4, 1992

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By M. G. Fleming

The professional mineral engineer is an individual of personal integrity who has undergone rigorous intellectual instruction in the scientific disciplines fundamental to his vocation; he has learnt to apply these disciplines to the discovery, mining and treatment of mineral resources and, through practical training and experience, has acquired competence and judgment to fulfil his undertakings. In the course of this development he has recognised and accepted a threefold responsibility to society, to his employer and to his profession

Dec 1, 1971

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By J. Ivon Graham, T. D. Jones

This paper presents methods in use in British coal-mines for the suppression of dust. While the effect of present-day treatment will not be apparent for several years, in pits in South Wales, concentrations as high as 50 gm./1,000 cu. ft. were some years ago fairly common in various operations at or near the coal-face, with an average concentration of 20 gm./1,000 cu. ft. Now the average concentration in what were previously dusty pits is probably not greater than 3 gm./1,000 cu. ft.Nevertheless, every effort must be made to improve conditions still further. In South Wales it is claimed that 99% of the coal-faces requiring treatment have been dealt with either by wet cutting, infusion, or hand-spraying. The extent of the treatment by these methods can be gauged by the fact that the total length of coal-faces now being treated by water infusion in Cardiff and Swansea areas is about 33,000 yds., by wet cutting 25,000 yds., and by hand-spraying nearly 14,000 yds. The influence of methods of mining upon dust production is only mentioned very briefly in this review, and there is no doubt that much more is to be learned concerning this aspect. It can be stated, however, that good mining practice is essential to prevent unnecessary dust production, and the problem of dust in mines will be solved only by the closest co-operation between mine managers, workmen, and scientists.

Jan 1, 1947

By G W. Clamp

The most traum atic event within the lUK coal industry during the last 30 years was its privatisation. Who were the relatively unknown people from RJB: white knights or robber barons? This paper highlights the strong safety and progressive engineering cultures th at existed and continues within the company. A long-term view of the business coupled with proven professionalism is amply developed. Quite dearly, to revert to private ownership is not a return to Victorian values but ‘back to the future’.

Jan 8, 1997

By J. Temporal

An introduction to the conference material in this issue is given together with the issue contents list, closing remarks by its chairman Dr. J. Temporal, the list of contributors and their companies, and the information that the 26th Sir Julius Wernher memorial lecture had had to be presented by the lecturer's wife, M. Biggart, in his absence due to site problems on the Storebaelt project

Jun 16, 1905

By III, Peter J. Rogers, J. Gordon Ogden

A study is described which attempts to identify the chemical factors of common concern to environmental and exploration geochemistry as indicated by recent work in both disciplines in Nova Scotia. Cores taken in lake sediments define geochemical baselines for the modern and pre-industrialisation periods. The investigation of lake and stream drainage indicates the presence of numerous chemical and organic factors that can be attributed to man's activities, such as construction and energy consumption. Geochemical surveys of lake and stream sediments are used to locate potentially toxic, high risk areas in Nova Scotia. Rapid change occurs in most surface drainage systems with the possibility of numerous chemical reactions taking place. It is found that spatial and temporal variations in the chemistry of modern and recent sediments are of interest to exploration and environmental surveys.

Jan 4, 1992