Search Documents

By K. Sasaki, H. Miki, Y. Muta, T. Hirajima, G. P. W. Suyantara

"Selective flotation of chalcopyrite and molybdenite is continuing problem since its selectivity is not perfect and current NaHS process needs closed system flotation plant because of hydrogen sulfide emission on acidic condition. Some alternative additives investigated as chalcopyrite became hydrophilic and molybdenite kept hydrophobic. XPS analysis indicated chalcopyrite became hydrophilic since iron and copper sulphate, hydroxide was covered on the surface whereas molybdenite kept hydrophobic since only molybdenite can be seen. Flotation experiments of chalcopyrite and molybdenite mixture sample indicated excellent separation that 95% of molybdenite can be recovered as froth and 93% of chalcopyrite can be recovered as sink. Flotation experiments with real bulk flotation concentration indicated similar separation result compared with current NaHS additive system. Possible mechanisms and detailed phenomenon were investigated based on the surface analysis and thermodynamic calculation etc. this alternative additive is easy to handle compared with NaHS since it does not emit effluent gas and commercially preferable.INTRODUCTIONMany copper mine often associates molybdenite (MoS2) as trace mineral. It is important to separate molybdenite and copper mineral efficiently since molybdenite is valuable mineral and also contamination of molybdenite into copper concentrate decrease concentrate value. Conventional separation of copper sulfide and molybdenite has been achieved with sulfide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulfide (Bulatovic, 2010; Ansari and Pawlik, 2007b). However, this current process shows imperfect molybdenite recovery (Liu et al., 2012, Zanin et al., 2009) and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant (Ansari and Pawlik, 2007a). there are still unknown on the effect of depressant NaHS, but one of the theory is NaHS reductant effect. It is worth to investigate the effect of other reductant as depressant on chalcopyrite. On this research, typical reductant, Na2SO3 are added to utilize for selective flotation of chalcopyrite and molybdenite."

Jan 1, 2018

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By P. Somasundaran, Tarun Bhambhani, S. Murthy Khandrika, Partha Patra, D. Nagaraj

Fine and ultrafine mineral particles, particularly if, altered mineralogically, can have detrimental effects on selective separation of minerals. Behaviour of altered mineral fines has been investigated in this work by studying the effects of weathered silicate slimes on the selective separation of copper minerals, particularly with focues on effect of the pulp rheological behaviour, which plays a governing role in the process. Physicochemical properties of these altered silicates fines such as morphology and surface charge are proposed to be responsible for the adverse rheological effects and resultant selective separation. Here, the effect of a number of problematic aspects such as water chemistry, froth stability, physicochemical aspects of gangue mineral aggregates on flotation sub-processes has been studied. Processing problems owing to the physical aspects of the gangue minerals, shape and morphology, are primarily due to uncharacteristic increase in the pulp viscosity. While problematic aspects other than impact of pulp rheological behaviour can interfere with each other in their contributions to how they affect the sub-processes, effects owing to pulp rheological behaviour have a direct impact on the flotation performance. Subtle increase in pulp viscosity can interfere with sub-processes in flotation leading to decrease in recovery and grade, and it is difficult to assess the effects due to such subtle changes. Reagent based strategies to overcome the problematic aspects has been explored here.

Jan 1, 2014

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By Y. H. Wang

Micro-flotation tests of spodumene, beryl, quartz and feldspar have been carried out by using CaCl2 and FeCl3 as modifiers and a blending collector of oleic acid and hydroximic acid. CaCl2 shows efficient activation for spodumene when pH is above 11.5, and FeCl3 exhibits a markedly activation and good selectivity for spodumene in the range of pH 4 to 10. The main species of CaCl2 are CaOH+ and Ca(OH)2 when pH is above 11.5, and the main species of FeCl3?6H2O are Fe(OH)+2 and Fe(OH)3 during the pH range of 4 to 10. A selective flotation of spodumene and beryl from pegmatic ore had also been completed while using FeCl3?6H2O as activator and the blending collector. A bulk concentrate containing 1.087% BeO and 4.70% Li2O has also been obtained in the flotation of spodumene and beryl from pegmatic ore assaying 0.097% BeO and 0.45% Li2O, and the recoveries of BeO and Li2O in concentrate are 74.38% and 69.50% respectively.

Jan 1, 2014

By Pamela Castillo, Marcia Muñoz, Rodrigo Luca, Brian Townley, Fernando López

In the present study we discuss the value of multi-element geochemistry as a tool for semi-quantitative to quantitative bulk mineral characterization in geological and geo-metallurgical modeling of porphyry copper type deposits, with an emphasis on hydrothermal alteration associations, types and intensities. In mine production of porphyry copper deposits much effort is placed on ore grade and geological modeling, applied for predictive mineral processing behavior, from blasting, grinding, leaching or flotation, down to waste disposal and environmental management. High confidence geological models are commonly based on geological mapping of drill core and surface/ underground exposures, combined with discrete mineral characterization (e.g., petrography, QEMSCAN®, spectroscopy, etc.). Unfortunately these are expensive and applied to limited numbers of samples, thus lacking sufficient representation and not suitable for geo-statistical modeling. In addition, geological mapping always presents uncertainty, based mostly on qualitative estimates. The combination of information usually provides geological models that are hard to combine with geo-metallurgical data, much less with mineral processing predictive behavior models. The advent of multi-element geochemistry, at low cost, has allowed employment of such tools massively, yet little use is given to the data, usually focused on elements of economic interest (main ore and credits) and elements of negative impact to concentrates and/or process. Geochemistry reflects the mineral composition of rocks, thus allowing characterization of lithology, alteration types and intensities, and mineralization. As examples of such applications we present generic classification techniques which were developed on various porphyry copper deposits of northern Chile, these based on multi-element geochemistry, allowing for semi-quantitative to quantitative high resolution modeling of key aspects of lithology, hydrothermal alteration and mineralization, and which may be cross-referenced to metallurgical test samples and by that, to geo-metallurgical properties of rocks and modeling. In addition, as data is quantitative and continuous, modelling of gangue can benefit from geo-statistical modeling.

Jan 1, 2018

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By R. ?. Sherembayeva, ?. ?. ?uktybayeva, ?. B. Rakhimbekova, N. ?. ?m?rova

"Studying the interaction of the phosphorus-containing flotation reagent with the components of the flotation system ""liquid-gas-solid"" during flotation of non-ferrous metal ores allows regulating the enrichment process. The phosphorus-containing reagent-collector anabasinium-O,O-dimethyl-thiophosphate has beensynthesized under laboratory conditions and the concentrated aqueous solution of anabasin hydrochloride and the 40% solution of sodium hydroxide have been used as the raw material. The phosphorus-containing reagent has been obtained by interaction of the anabasine base, sulfur and dimethyl phosphite, due to sulfur and nitrogen atoms it can form complex compounds with heavy metal ions.Studying flotation of copper-sulfide ore of the Sayak field with the use of the phosphorus-containing reagent-collector anabasinium has been performed in the open and closed cycles. The degree of ore grinding was 60- 62% of the class -0.074 mm. There has been established the dependence of the ore flotation parameters on: a) pH of the pulp; b) the consumption of the reagent-collector anabasinium.The effect of the pulp pH on the technological parameters of copper ore flotation has been carried out with a reagent regulator that increases the difference in the surface properties of the minerals to be separated.There has been used lime as the regulator of the medium, the consumption of which varied from 750 to 1500 g/t; the consumption of the reagent-collector anabasinium was 10, 15, 20 and 25 g/t.It has been found that when flotation of copper ore without the use of lime at pH equal to 7.8 and at the reagent consumption, g/t: anabasinium - 25, T-92 - 55, copper recovery in the concentrate is 92.72%, the quality of concentrate is 7, 1%.In flotation according to the factory mode (the consumption of xanthate is 44 g/t, T-92 is 55 g/t, pH = 7.8 (without lime)) of copper ore, copper recovery in the concentrate is 87.38%, the concentrate quality is 7, 97%, with reducing the xanthate consumption to 25 g/t copper recovery is reduced to 83.39%, the quality of the concentrate is up to 6.69%.In the experiments using the factory reagent mode in the closed cycle, with the xanthate mass consumption of 44 g/t, T-92 blowing agent of 55 g/t, the third recleaning concentrate contained 19.13% copper with recovery of 86.89%.Using a phosphorus-containing reagent instead of xanthate with the same flow rate, the third recleaning concentrate with the mass fraction of copper of 19.82% has beenobtained with recovery of 87.77%."

Jan 1, 2018

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By R. Prakash

Column flotation has now gained wide application in the recovery of various minerals. The performance of the flotation device depends on the mixing characteristics of the phases inside the devices. In this work, quality of mixing in a flotation column has been analyzed by using information entropy theory. Empirical models have been developed for flotation column with the parameters which affect the quality of mixing. The efficiency of the particle separation in the flotation column has been enunciated based on the quality of mixing. The present analysis on the quality of mixing in flotation column may give insight into a further understanding and modeling of flotation devices in industrial applications.

Sep 1, 2012

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By A. J. Lynch, D. K. Tungpalan, Y. Reja, E. C. Avelar, G. Figueroa, S. Gómez, R. Alanis, M. A. Corona-Arroyo

"Have you been on a mine site? This question was posed by Emeritus Professor Alban Lynch to Higher Degree by Research (HDR) Students from the Sustainable Minerals Institute - Julius Kruttschnitt Mineral Research Centre (SMI-JKMRC) in the Student Technical Presentations in 2015. From that question, five HDR students from SMI-JKMRC organised a placement on mine sites in Mexico. The SMI-JKMRC is well known for its tradition to provide their students with opportunities to enhance and test their skills in mineral processing plants. The Student Venture became a short internship for HDR students which had the objective of establishing collaboration with mining companies in Australia and overseas, and of providing a unique experience for the HDR students in regard to their training, professional development, networking and cultural interchange. In return for the companies’ support, the students conducted plant audits to evaluate the process performance thereby providing valuable data to the host company. The 2016 Student Venture was held at the Grupo Peñoles & Grupo Fresnillo in Mexico, in which three mine sites received five HDR students from JKMRC and one young researcher from Universidad de Guanajuato (UG). This paper describes the positive outcomes for the mining company and the students for this experience. The Venture was considered very successful, as it provided valuable training for the students as well as in depth information about the operation of the comminution and flotation circuits of the host sites for the Grupo Peñoles & Grupo Fresnillo. The experience also provided an opportunity for an exchange of knowledge between the HDR students and the site personnel from the host operations. The indication of the success of the experience for all involved was the support of the host company in future student internships."

Jan 1, 2018

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By S. Makni

Flotation is a complex process in which many mechanisms come into interaction. In this paper, an approach to model these mechanisms in order to predict size-by-size flotation performances is presented. The estimation of the collection efficiency of particles takes into account the serial sub-processes of particle-bubble collision, attachment and detachment. The model was applied to an industrial plant and yielded satisfactory results whereby the actual flotation performances could be correctly predicted. Furthermore, the flotation model allowed investigating the possibility of improving flotation performances by a split flotation feed in comparison to the actual single-stage process.

Sep 1, 2012