Search Documents

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

By Martin Rudolph

"Flotation is without a doubt one of the major processes for the separation of fine minerals and it has been applied for more than a century. A key task of a successful flotation separation is to find the proper chemical treatment to selectively hydrophobize and thus float a certain mineral phase using molecules or ions referred to as collectors, depressants, regulators and frothers. Commonly floatability is determined by microflotation tests using the Hallimond tube with pure mineral phases. This method however requires the pure mineral phase which is very often not even taken from the same deposit which is going to be processed. In this paper we present a new approach to in-situ determine and even map the floatability of finely disseminated mineral phases within cross-sections of an ore. It is based on measuring hydrophobic effects using colloidal probe atomic force microscopy with a hydrophobic polystyrene probe based on force spectroscopy with a lateral resolution of only a few nanometers. Coupled confocal Raman spectroscopy on the same locality enables the identification of the mineral phase. We present the working principles of the method and show which signals in the force spectra characteristic for hydrophobic interactions can be used to define floatability and which can then be mapped as single quantities, e.g. jump-into-contact events due to nanobubble occurrence or parameters of the long range interaction curves most probably due to capillary effects. A finely grained silicate ore containing the valuable rare earth mineral eudialyte from southern Sweden as well as pure samples of magnetite are presented as substrates to demonstrate the capability of this new approach. This method will not only help to find the proper flotation chemistry but it can furthermore help in researching and unravelling problems of floatability within similar mineral phases."

Jan 1, 2014

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By Henrique Kahn, Daniel Uliana, Juliana Antoniassi, Viviane Shimizu

"Mineral exploration and geometallurgy require a large number of samples for physical, chemical and mineralogical assays. The combination of all these data and their spatial distribution define the ore variability. This is important in exploration programs and crucial in feasibility studies as well as at the production operation level. Ore mineralogical composition and its associations, characterizing the geological formation and mineralization, are the main keys to define the ore domains and its variability, which can be quickly assessed by cluster analysis and by modern automated mineralogy tools. One hundred and ten copper ore samples from Sossego mine, in Brazil were compared and classified by X-ray diffraction cluster analysis based on the position and the intensity of the diffracted peaks. Initially four ore types were categorized based on content of major minerals: quartz, feldspar, amphibole, iron oxides, mica and chlorite. Results showed a strong correlation between the grouping and the samples location in Sequeirinho and Sossego orebodies, with a straight link to types/intensities of hydrothermal alteration prevailing in each body, which reflects the mineralogical composition and thus the X-ray patterns. Samples from four recognized ore types were submitted to detailed automated mineralogical studies by electron beam image analysis and differ strongly from each other regarding their chemical and mineralogical compositions and relevant parameters for mineral processing. Chalcopyrite is essentially the only valuable mineral, occurring both as submillimetric grains included in other minerals and as larger crystals. Except for pyrite, other sulfide minerals occur as traces. Chalcopyrite liberation curves indicate that samples from Sossego have higher liberation degree than those from Sequeirinho. The proposed method proved to be very efficient and accurate to classify a large number of samples within a short time frame, allowing the distinction of the ore types regarding their mineralogical composition as well as the mineral processing parameters."

Jan 1, 2014

By P. Somasundaran, G. Anastassakis, Z. Pan, D. R. Nagaraj

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By D. G. Hulbert

"Mineral processes are complex operations that have been modelled, controlled and simulated by diverse technologies. A review is given of some models of mineral processes in the literature. A new variation of a dynamic process model of flotation is presented. Process models, describing real and relevant physical variables, give a good understanding and good qualitative simulations, but can sometimes require prohibitively difficult and extensive parameter estimations. Process control is usually best done on operational plants by the fitting of system models, which can home in on the plant?s observability, controllability and optimisation. System models can be of a form amenable for use in appropriate techniques for controller design and implementation. The control of milling circuits is discussed in some detail. While simulators use models to predict dynamic or steady-state information, part of their strength lies in their ease of use and their ability to test different types of specifications. Some results are given for a flotation circuit simulator that can be made to solve virtually any permutation of specifications.INTRODUCTIONThe development and application of appropriate technology can lead to better operation of mineral processing plants in industry, so that substantial benefits can be obtained from improved throughputs, efficiencies and product qualities. This paper addresses some of the principles and methods used in the quest for the development and exploitation of such technology. Although the design of processes is often the motivation for modelling and simulation, this paper also targets the use of modelling and simulation for the control and optimum operation of mineral processes. The two processes given the most attention here are flotation and milling.Technologies used in mineral processing range from simple to very complex. Simple technical principles, such as mass and component balances, can yield some simple and effective strategies for modelling and control. However, minerals in particulate form have such complex physical and chemical properties that there appears no end to the complexity that emerges, as more and more factors are taken into consideration in the pursuit of better results and understanding. The situation is aggravated by the complexity of mineral processing plants, which have spatially variable conditions within process units, and complicated interactions between these units."

Jan 1, 2003

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By N. Ahmed

This paper is concerned with the drainage behaviour of gangue mineral in the froth phase. Experiments were carried out in a continuous laboratory flotation cell in which froth depth and bubble size could be changed independently. The fraction of solids returning from the froth to the pulp zone was expressed using a rate constant. A mixture of hydrophilic solids (silica) and floatable particles (glass ballotini) was used as a flotation feed. Samples of glass ballotini of different hydrophobicities were obtained, using controlled silanation. Three samples, with contact angles of 50, 66, 82 degrees, were used. The effect of the initial bubble size (pulp bubble size), concentration of gangue mineral in the froth zone, and froth depth on the drainage of silica, were investigated. The drainage rate of the entrained solids increases with an increase in the degree of hydrophobicity of the floatable particles. Concerning the effect of pulp bubble size on the drainage rate of entrained solids, larger bubbles always give higher drainage rates due to formation of relatively loose froth structures which allow gangue particles to easily move down to the pulp zone. Conversely, smaller bubbles exhibit lower drainage rate constants, in particular at shallow froth depths.

Jan 1, 2003

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By V. Yu. Ivanov, A. I. Yuryev, L. S. Lesnikova, M. S. Datsiev

"The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before. In 2003-2005, the process upgrading included the differentiated processing of nickelpyrrhotite products recovered at the different concentration stages and made it possible to significantly enhance the contrast of the pentlandite and pyrrhotite flotation properties and to simultaneously increase separation of polymineral intergrowths.The next stage of the PD concentration complex development is the Project ""Talnakh Concentrator Reconstruction and Technical Upgrading"" to raise its capacity by half. The project has three Phases.• Phase 1. Pilot startup was carried out in January 2015 following the installation of new OK-100 TC flotation machines, manufactured by Outotec.• Phase 2. The introduction of a new technology developed by the Polar Division specialists launched in mid-2016. The new technology is based on maximization of iron and sulfur removal into tailings and maintenance of non-ferrous and precious metals losses at the same level.After the realization of Phase 3, the annual capacity of the Talnakh Concentrator will raise by another ~ 40% at the expense of processing cuprous and disseminated ores currently being processed by the Norilsk Concentrator.By 2023, due to upgrading of the PD production facilities the emissions to the atmosphere will reduce by 75%.Polar Division of PJSC MMC Norilsk Nickel (PD) searches for the ways to solve its environmental issues. Thus, in 2016, the Nickel Plant was shutdown and a new flowsheet was introduced at Talnakh Concentrator. It resulted in the reduction of sulfur specific amount sent to pyrometallurgical processing as a component of the concentrates.The Talnakh Concentrator was put into operation in 1981 using a direct selective process to produce copper, nickel and pyrrhotite concentrates.In 1981, its design capacity for processing of Cu-Ni ores from Oktyabrsky and Taimyrsky Mines did not exceed 3 million tons per year.In 2001, a novel selective-bulk-selective (SBS) technology for the concentration of massive sulfide ore was implemented at the Talnakh Concentrator, that allowed to increase the valuable components recovery into target concentrates with feedstock grinding coarser than before."

Jan 1, 2018

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By S. V. Petrov

Oxidised ores possess a significant share among raw materials which are treated by traditional plant technology. As usual, the chemical composition of these ores is rather simple. They can be treated by standard cyanidation. In this case, the resulting wastes have an alkaline reaction. Their toxicity (in case of ROM ores treatment) is mainly due to the presence cyanides and thicyanades. The tails are dexotified before disposal. However, chemical reagents used cannot provide a complete removal of toxic matters. In this case, this disposal poses a real problem because these tails contain a significant amount of CN and SCN and their behavior during a long disposal should be studied. A sample with a simple composition taken from cyanidation tails was studied. The sample presents itself the quartz low-grade sulfide gold-bearing ore. Sulfide sulfur content is 0.15 per cent,and heavy metals content is 0.023 per cent. Method of testing is described further. The samples were tested under moderate and subarctic climates based on the difference in temperature, moisture and the degree of oxygen saturation of air. The pH of water extract, which was prepared using distilled water, was also determined besides measuring the concentration of cyanides and thiocyanates. This demonstrates the stability of sulfide-bearing minerals in the disposed tails. The tests time was 820 days. It was found that the alkalinity of the samples tends to lower under oxygen-containing conditions in proportion to temperature increasing. Under conditions without oxygen, the pH lowering is minimal. Mineralogical and chemical properties of the ore material give positive alkaline balance during testing. The solid sample contains enough alkaline agents to compensate dangerous to the environment reactions of sulfides oxidation.pH value maintaining under alkaline conditions witnesses to the possibility of a safe disposal of this tails type. The largest amount of cyanide is removed under acid-containing conditions at positive temperatures. The higher the temperature is, the more intensive destruction is. At the moment, of finishing the tests at 20ºC temperature, the residual concentration of CN- was 0.06-0.10 mg/L, at 4ºC, the residual concentration of CN- was 0.2-0.3 mg/L and at -18ºC was 0.4-0.6 mg/L. Under conditions with the lack of oxygen, cyanides can be removed within the first 200 days. Then, this process fully stops. A stabilized cyanides concentration is 3.0-4.0 mg/L. The presence of sulfides increases the content of cyanides at the initial stage of testing. Then, the concentration of SCN at the temperatures above 0ºC decreases rapidly under oxygen-containing conditions. At the rise of temperature, a narrowing of peak at the curve and an increase of the destruction process are observed. At the end of testing, the concentration of thiocyanates in the moisture of wastes was 0.2-0.3 mg/L at the temperature of 20ºC and 0.5-0.6 mg/L at the temperature of 4ºC, respectively. The concentration of thiocyanates contained in a frozen sample and media which have the lack of oxygen stabilizes at a certain level owing to sulfides and does not practically change further. It was found that detoxification of oxidized cyanidation tailings with a simple composition which were disposed as filtration cakes can be possible. In this case, the concentration of cyanide in the moisture of disposed wastes can have a close value or equal to actual concentration during cyanidation. In order to meet the requirements of high ecological safety standards and successful detoxification process of toxic compounds in the tails under the action of natural factors, the conditions of air aeration with oxygen for the whole volume of tails are required. Keywords: cyanides, thiocyanates, storage, detoxification, flotation cakes

Sep 1, 2012

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St. Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

By Kaustubh Joshi, Pradip, Beena Rai, Kesri L. Menaria, Venugopal Tammishetti

"Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. High alumina is deleterious for the performance of both blast furnace as well as sintering plants. Slimes generally contain 5 - 10% alumina, and hence despite assaying as high as 60% Fe, those are dumped in tailing ponds. The slimes are typically less than 37 microns. Selective flocculation of iron ore slimes using highly selective reagents is thus an option worth exploring. Our research is directed at employing state-of-the-art molecular modeling techniques for the selection/design of selective reagents for this separation. We have earlier reported our results on starch as a selective flocculant for iron ore slimes. In this paper, we present our results on the selective dispersion-flocculation of natural iron ore slimes using guar gum flocculant. With careful selection of various process parameters such as flocculant dosage, dispersant dosage, pH and settling time, we were able to obtain a concentrate assaying >66% Fe and <3.5% Al2O3 with an yield of 65 to 68% (recovery of iron values more than 70%) from a natural iron ore slime sample assaying 58% Fe and 7% Al2O3."

Jan 1, 2014