Search Documents

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By I. H. Mukhametshin, E. N. Baranova, I. B. Fadina, E. A. Ashirbaeva

The purpose of the research is the development of a complex of solutions for the maximum extraction of non-ferrous and precious metals from persistent mineral raw materials by heap bioleaching from spent heap leaching (HL) stacks. Methodical recommendations for assessing the suitability of primary and technogenic refractory mineral raw materials for heap bioleaching are developed. Active associations of microorganisms have been created for the conversion from various types of ores to the solution of S, Fe, As, Sb, Cu, Zn, Mn, Ni, Mg, P and other elements, as well as methodologies for their storage, immobilization and preparation of bioreagents in industrial conditions. On a pilot scale, tests were carried out on samples weighing 15-17 thousand tons of refractory gold-sulphide ores (more than 50% of gold is associated with sphalerite), gold-quartz ores with colloidal gold (74% associated with quartz and pyrite) and gold-silver ores with elevated copper and zinc content (1.5 and 3,5%, respectively), as well as man-caused material lying for 4-5 years of spent quarry material of oxidized gold-silver ores. In the pilot-industrial tests of heap bioleaching of gold-sulfide ores, gold recovery of 84-85% and silver was achieved to 89-90%, the possibility of obtaining high-yield solutions of copper and zinc, suitable for hydrometallurgical processing, from gold-silver ores, and the possibility of obtaining waste with a dump content of valuable components, suitable for deep disposal in the construction industry. When comparing two technologies for processing refractory ores after biooxidation under HL conditions, when 1000 tons of ore processed by the bioreagent were re-milled from a size of 40 mm to 0.1 mm and cyanated under the conditions of the factory process, the same results were obtained for gold recovery (85%) and silver (90%), as with the heap version. The copyrights of the development are protected by a patent.

Jan 1, 2018

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and the dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is the main parameter for precipitate flotation in pilot or industrial scales. The suggested limiting factor is the aggregate stability under the turbulence created by the rising bubbles. The stability of precipitate is related to the structural organisation of aggregates, which determines the size distribution of particles during precipitation and flotation stages.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions. The fractal studies allow the detection of a structural scaled organisation of the precipitate flocs. The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with restructuring or breakage phases.The destruction process, which occurs for the lowest values of the dissipation energy E (0.02 . 0.05 W/kg) was characterised by a fractal dimension Dg of size distribution. Besides, the destruction of floc produces very fine particles, and thus induces the difficulties of bubble-particle collision during the precipitate flotation in column."

Jan 1, 2003

By P. Thareja, V. Prasad, S. P. Mehrotra

In recent times, the transportation of minerals and their tailings has become a major concern across the world. There exists a huge demand of efficient and cost effective transportation system which poses minimum environmental damage. One of the economically and environmentally viable techniques which potentially offer a solution to the above problem includes transportation of minerals and their tailings in the slurry form through pipelines. Slurry transportation through pipelines is reported to be more beneficial in terms of cost, environmental impact, maintenance and safety when compared with other conventional modes of bulk transportation such as train, truck, barge and conveyors. The main challange associated with hydraulic transportation of slurries is to obtain a non-settled slurry and to design a pipeline system which results in the optimum energy requirement for transporting a large throughput to longer distances at a lower cost. The feasibility of hydraulic transportation of slurries through pipes mainly depends upon slurry properties and flow conditions in the pipe. Results from rheological studies exhibit the presence of shear thinning flow behaviour of minerals and their tailings in water. The flow behaviour index (n) and consistency coefficient (k) obtained from the rheological analysis are further used for the specific energy consumption and energy losses during transportation. The cost of transportation in USD per ton per 100 km and transport capacity in tons per day are calculated from the specific energy consumption to transport these slurries. The results demonstrate that the slurries can be transported to long distances (say, 100 km or more) corresponding to optimum energy consumption and dissipation rate at a substantially cheaper cost than the existing rail and road transport in India. Although we have carried out transportation studies with coal fly ash (CFA), lignite & bauxite slurries, for paucity of space, the results reported here are essentially for CFA slurries. Details of our investigations with lignite coal & bauxite will be reported seperately.

Jan 1, 2018

By S. Schade-Dannewitz

In terms of a sustainable waste management, high recycling rates and purities of the different collected waste components are very important. Especially the recycling of used packaging materials with valuable components like plastics, ferrous and non-ferrous metals and liquid cartons (light weight packaging) requires a complex technology. In plants to recycle those light weight packaging materials films cause problems and often manual sorting is necessary to remove them. The Nordhausen University of Applied Sciences together with the company Schulz & Berger from Altenburg tries to replace manual sorting with fully automated technologies. The objective is a technology that can enable a high recovery of recyclable film and satisfy the maximum purity requirements for the film fraction. For that purpose, a new machine called Low-pressure Separator was developed. The test materials used consist of separately collected recyclables from the yellow recycling bins or bags in Germany?s Dual System (Duales System Deutschland ? DSD), the recyclable waste collection system. First tests show that high purities of the film-fraction, for example the required 92% or higher, can be realized. Next to the film-purity, furthermore the mass yield and the recyclable yield are discussed because they play an important role to evaluate the efficiency of the recycling process. Further activities to improve and establish the developed technology are mentioned.

Sep 1, 2012

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By N. D. Dementieva

Based on lab and pilot-plant tests to recover gold, silver and lead of a Russian deposit, a collective and flotation concentration flow sheet with lead and sulfide concentrates was proposed. The type of the deposit is gold-sulfide-quartz-bearing. The recovery of gold, silver, and lead to a lead concentrate was 47.4%, 68.1% and 70.7%, respectively. The grade of gold and silver grade was 170 g/t and 372 g/t, respectively. The mass percent of lead, zinc and arsenic mass percent was 41.7%, 0.34% and 0.63%, respectively. The recovery of gold and silver recovery to a sulfide concentrate was 50.1% and 28.8% at the grade of gold 20.5 g/t and silver 66.2 g/t. Sulfide concentrate with arsenic mass percent ~3% was biooxidised followed by CIL and obtaining metal at the site as well as zinc concentrate from bioleaching solutions with zinc mass percent 45% at its 64% recovery. The total gold and silver recovery using a developed technology with the account of their treatment at a polymetallic plant was 92.2% and 93.7%, respectively.

Sep 1, 2012

By Vasily V. Lodeischikov, Adolf F. Panchenko, Olga D. Khmelnitskaya, Vladimir E. Dementyev

Pilot plant tests of underground gold leaching from Maminskoye deposit oxide ores at a grade of 0,7 g/t Au were carried out. The underground leaching flow sheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution on active carbon, carbon concentrate ashing and calcine melting to produce high grade gold concentrate. The underground leaching system throughput was 15 m3 of solution per hour. Gold concentration in pregnant solutions was 0.12-0.13 mg/l. Gold recovery from solutions into carbon was in the range of 63-84%. It was demonstrated that the low Au recovery in the adsorption cycle was due to the presence in pregnant solutions of "active" chlorine, which destroys active carbon and causes a sharp decrease of the carbon loading capacity for gold. To improve the adsorption indices, previously dechlorinated pregnant solutions using bituminous coal or Na2S2O3, is recommended. Ion exchange process was tested as an alternative for gold extraction from dechlorinated solutions. In the testwork period, 4.4 kg of gold were produced with a chlorine consumption of 3.5 kg per 1 g of gold. During the tests a program of environmental protection measures was completed to provide the necessary safety precautions of the underground leaching works.

Jan 1, 2003

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By David I. Verrelli, Peter T. L. Koh

"Recent experimental measurements of induction time made by direct observation with the ‘Milli-Timer’ indicated that angular particles were able to attach much more rapidly than spherical particles. There was around a tenfold difference in the respective induction periods for particle-bubble attachment. For industrial application, a more holistic comparison is needed, with the induction period for attachment being just one input. Over the years, CSIRO has developed a CFD-flotation model that incorporates both rigorous hydrodynamics, to simulate real industrial cell geometries, and a detailed model of the embedded flotation process, in which the induction period is an important parameter. We conducted transient modelling of batch flotation. First, spherical particles were modelled, as a ‘baseline’, for different particle sizes and levels of hydrophobicity. In the second set of results, the induction period was decreased by a factor of up to ten, simulating flotation of angular particles. Flotation recovery was found to depend upon induction period in a complex manner. For highly hydrophobic or fine particles, the induction period for spheres was already so low that recovery was limited by other factors (e.g. bubble-particle collision frequency). Further decreases in induction period, as for angular particles, did not have a significant effect on recovery in these cases. By contrast, when weakly hydrophobic or coarse particles were modelled, the recovery was predicted to be greatly enhanced for angular particles, in comparison to spheres. For these particles the induction period was limiting recovery, so that the flotation rate constant could be improved directly by reducing the induction period. This is consistent with batch flotation experiments using Ballotini reported earlier. Therefore, when dealing with weakly hydrophobic particles or relatively large particles that are to be floated, an enhancement can be expected for more angular particle shapes. In such cases, judicious specification of the grinding circuit may improve the overall efficiency."

Jan 1, 2014

Gold thiosulfate complex is difference with gold cyanide complex, which is easily adsorbed on activated carbon while gold thiosulfate complex cannot be satisfactorily recovered by activated car-bon. However, Gold thiosulfate could be recovered by activated carbon if cyanide is added into the thiosulfate solution. To avoid the cyanide solution, this paper will review several possible processes to recover the gold from thiosuldate solution: such as the cementation with metals, ion exchange resin and solvent extraction. The gold cementation with the powders of zinc, copper, iron and aluminium will be discussed. The advantage and disadvantage of each are compared. The consumption of thiosulfate and copper and feasibility of solution recycling will be discussed. The gold recovery by some ion exchange resins will be suggested. The processing conditions, its applications and the resin elution methods will be presented. The gold recovery by using solvent ex-traction will be reviewed. The processing conditions of solvent extraction process are discussed and compared.

Jan 1, 2014

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By A. P. Wang

Porous carbon adsorbents derived from inorganic materials templates such as zeolite and mesoporous silicate attracted considerable attention in the last decade and got great progress in re-cent years. However, so far almost all of templates used in the process were artificial porous materials; the porous carbons prepared by this method are very costly, which restricts the synthesis and application of templated porous carbons. In order to reduce the cost of templated porous carbons, natural inorganic porous minerals have been taken into consideration, which maybe possible and promising templates to prepare carbon adsorbents. In this work, we describe template process using tubular halloysite, rich mesoporous zeolite and low bulk density diatomite, as exemplars of the categories of inorganic porous templates which we have studied and discussed the effects of different templating structure on the resultant carbons. Two main carbon precursors, sucrose and furfuryl alcohol, were used respectively. The morphology of minerals and corresponding templated carbons were characterized using electron microscopy. The pore structures of minerals and templated carbons were characterised with nitrogen adsorption. The results showed that the morphology and pore structure of porous carbons are in good pertinence to those of corresponding templates. The morphology and pore structure of templated carbons could reflect those of corresponding templates at nanometer level. The templated carbons with high specific surface areas and rich mesopores can be prepared by using these three kinds of natural porous minerals as templates. The higher the surface area and pore volume of the minerals, the higher those of the corresponding carbons. The template carbons from halloysite possessed higher pore volume and mesoporosities. Based on the large mounts of experiment results, a model for the mechanism of resultant nanopores formation has been proposed. The nanopores of templated carbons are mainly composed of three kinds of pores: templated pores formed by removing mineral, hereditary pores formed by inheriting the pores of templates and nanopores formed during carbonization. These three kinds of pores have a close relationship with corresponding template.

Jan 1, 2014

By Johannes Käppeler, Alexander Weh, Harald Giese, Klaas van der Wielen

"High voltage breakage is a novel comminution technology that shows considerable potential for various applications in mineral processing and recycling. It relies on highly energetic electrical pulses to induce electrical explosions in rocks, causing the formation of plasma channels and powerful shockwaves that result in fracturing and fragmentation of particles. There has been considerable interest in this technology for its ability to weaken rocks and preferentially liberate target minerals, as previously demonstrated by other authors. Weakening has the potential to significantly reduce energy consumption during comminution, or alternatively, increase throughput of a circuit. Better liberation may yield an improved concentrate grade and/or recovery, reduce fines losses to tailings or increase the grind size required for liberation, thereby also reducing energy requirements. This review aims to increase general awareness of this technology, and promote further research into it by providing a general summary of the theory underlying high voltage breakage, as well as the envisaged applications of this novel technology. A brief history of the technology is presented before progressing onto the physics underlying the electrical and geomechanical aspects of high voltage breakage. Key results regarding weakening and liberation are discussed, and some mention is made of current challenges and planned developments to increase the throughput of high voltage breakage units to the level where it can be integrated into new and existing processing circuits."

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By Vladimir Vigdergauz, Sergey Kondratiev

The paper reviews the existing criteria of the formation of particle-bubble aggregates during flotation. It is shown that predictions obtained by these criteria do not completely fit to the interaction between mineral particles and air bubbles. Experimental results of the studies into the influence exerted by molecular forms of collectors on the particle-bubble interaction are reported. Rate of dry spot expansion on the surface of pyrite with various combinations of chemically and physically adsorbed xanthate are examined. It is shown that molecular forms of collectors accelerate the rate of dry spot expansion on the mineral surface after the local rupture of the water film between particle and air bubble. The authors come to a conclusion that the molecular forms of collectors remove water from the interlayer between mineral particle and air bubble during their contact. Similarities of the proposed mechanism with the action of ion-molecular associates of fatty acids and amines are discussed. Reagents with high surface pressure and rate of spreading at the water-bubble interface are required for the effective interfacial dewatering. It is concluded that the value of surface pressure can serve as the criterion for efficiency of physically adsorbed reagents. The low surface pressure indicates weak collecting ability but high selectivity of the collector. Therefore, the presence of the molecular forms of collectors in the sorption layer is the necessary condition for formation of particle-bubble aggregates, and comparison of the surface tensions of collectors could be recommended as the estimation criterion of their flotation activity and selectivity.

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By Nicolus Rotich, Ritva Tuunila, Louhi-Kultanen. Marjatta

Most minerals, their ores, and gangue require sorting in order to maximize the recovery of the primary product during concentration. Gravity separation though old, is not obsolete and is continually playing an important role in mineral processing and many other industries, especially where plant energy efficiency is of concern. Screen designs e.g. material of construction, deck angle of inclination, the feed throughput, and physical as well as chemical properties of the particles, are critical factors to consider when using gravity for solid separation. Solids loading and screen geometry are significant, and easily manipulated operational parameters that affect both the screening rate and efficiency to a large extent. In this paper we applied nonlinear least squares optimization technique, and response surface methodology first, to assess the significance of the two factors, and secondly to select the best mathematical models that optimize both capacity and efficiency of the screening process. Initial experiments and confirmation tests were conducted on a prototype screen of 846.51cm2 effective area, (2100 cm2 total area). For glass beads of sizes 0.75-3mm, with feed loads of 10g up to 160g, and inclination angles from 5-20o, a maximum efficiency of 66.7%, and a screening rate of 22g/s was achieved with a screen loading of 86.5g, and an inclination angle of 12.43o. These results were then subjected to nonlinear least squares optimization, in which afterwards an optimum theoretical efficiency of 72% and screening rate of 31.2g/s were achieved at a loading of up to 104g. There was excellent performance at angles 12.5=?=17.5, but poor at the angles outside this range. The screening efficiency did not seem to respond significantly to changes in screen loading. Confirmation tests conducted at selected optimum parameters achieved an efficiency of 72.1% (at 17.5o with 88g load), and a rate of 27g/s at 16.5o with 104g.

Jan 1, 2014

By V. Y. Dementyev

Laboratory and pilot-plant testing using a sample of gold-bearing semi-oxidized ore from a Russian deposit followed by a flow sheet and reagent flotation mode development to design a plant was carried out in IRGIREDMET in 2009-2010. According to the developed flow sheet low alkaline flotation conditions are recommended in order to activate the surface of sulfides. The pH lowering from natural (7.5-8.0) to optimal (4.6-4.8) value using sulfuric acid provides for an increase in gold recovery. Before CIL, a final flotation concentrate is pretreated using pressure oxidation. It was found that the use of recycled solutions from pressure liberation in order to create acidic conditions for flotation instead of sulfuric acid during pilot-plant testing is recommended. The flow sheet offers the detoxification of remaining pressure oxidation solutions together with the flotation tailings. The carbonates presented in the tailings significantly reduce the consumption of lime for detoxification and allows for the use of two tailings dams instead of three. The first is used for the tailings of flotation and pressure oxidation recycled solutions, which were detoxified together. The second tailings dam is used for detoxified cyanidation cakes of the flotation concentrate. It was found during pilot-plant testing that flotation under natural and acidic conditions provides for 88.9 percent and 93 percent gold recovery, respectively. 4.1Au percent increase recovery was achieved due to the reduction of gold losses with flotation tailings and better quality of concentrates.

Sep 1, 2012