Search Documents

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Amit Srivastava, Monica Malhotra

In a congested city or urban area, so called “lifeline of the city”, i.e. Gas, Electricity, telecommunication, as well as other utilities or facilities are supplied or transported underground through buried pipes or utility tunnel. Sometimes these buried pipes or utility tunnels are deep underground and interfere with the foundation of new structure. It is highly probable that a pile foundation is placed near an existing underground buried pipe or utilities tunnel and may influence its load bearing capacity. Hence, estimation of reduce load bearing capacity of the pile foundation placed near the existing buried conduit or utility tunnel is a complex soil-buried structure interaction problem. It is further complicated owing to uncertainty in estimation of geotechnical parameters of foundation soil due to measurement and testing errors, inherent soil variability and model transation. Under such circumstances, load bearing capacity is best assessed in probabilistic framework or through reliability analysis. The present study demonstrates how concept of response surface method (RSM) in conjunction with Numerical Analysis and First Order Second Moment (FOSM) methods can be combined to per the reliability analysis. The study answers the following question “reliability in reduction in the load bearing capacity of single pile placed near the existing underground pipe or utilities tunnel”. It is demonstrated that the approach provides first hand ination on the reduction in the load bearing capacity and then estimate the reliability of that estimation in terms of an index called Reliability Index (). Such preliminary investigation can be useful for advocating the detailed analysis as well as in the decision making for relocation of pile foundation.

Sep 1, 2022

This Workshop was held at the Doubletree Inn, Seattle, Washington from September 26 to 28, 1997. Run under the auspices of the Deep Foundations Institute (DFI), it was co-funded by the newly formed Japanese Association of Micropiles (JAMP), and the Federal Highway Administration (FHWA). The Workshop was jointly organized and facilitated by Fujita Research Corporation and ECO Geosystems, Inc., with close support by Donald B. Murphy Contractors, Inc. DFI kindly consented to publish these Proceedings. As is clear from the list of attendees, 42 specially invited engineers from all aspects of micropile technology were present, representing Japanese, European and American practice. This proved to be a most friendly and interactive group of people, who freely exchanged ideas, views and close comradeship, not only during the technical sessions, but (and especially!) during the numerous social events. Perhaps the best illustration of this came in Day 2 when the attendees were divided into five competing teams, each comprising representatives from the different geographic groupings. These teams had to quickly devise solutions to two technical problems (using standard data previously provided. A team of "referees" (who also acted as "coaches") later determined the most apposite response, based on constructability design concept, cost, schedule and so on. Not only were the winning team very liberal in distributing the prize (vintage California champagne) among themselves, but the whole Workshop soon benefited from their generous division of the spoils of victory.

Jan 1, 1997

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By C. Vipulanandan

With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.

By Marco D. Boscardin, Benjamin H. MacKinney, Kenneth R. Allard, Kenneth A. Pidgeon, Adriane G. Boscardin

This paper presents a case history for a unique application of a system of vertical micropiles with horizontal soil nail bracing and shotcrete facing for underpinning. The system was used to support and protect an existing 2-story hospital building during demolition and renovation. The goal was to limit building movements and have the building remain in use during construction of an abutting addition. Soils at the site consisted of clean, loose to dense, sand and gravel. The original underpinning design was revised after the initial excavation revealed unsuitable soil conditions for traditional underpinning pits. An alternative system consisting of vertical micropiles (hollow bars) through the footing, combined with shotcrete and soil nails was proposed, accepted by the owner, and successfully constructed. Excavation depths were up to 15 feet (4.6 m) below the existing footings. Wall movements were monitored at regular, horizontal and vertical intervals along the hospital wall, and less than 0.6 inches (15 mm) of settlement and 0.1 inches (3 mm) of horizontal displacement throughout underpinning and construction were reported. The challenges with the original proposed support of excavation design and other alternative approaches considered will also be discussed.

Oct 1, 2022

By C. Vipulanandan, M. Dawood, Dongmei Pan

"With the aging infrastructure, there is a need to maintain and extend the service life of steel structures in general and steel piles in particular. Steel piles support not only vertical loads but also dynamic horizontal loads in onshore and offshore applications. In order to select the appropriate methods to repair corroded steel piles used in onshore and offshore application, corrosion mechanisms were investigated with the rate of corrosion in various environments. The corrosion rate of steel in soil, water and soil-water interface varied from 2 to 500 µm/year. Based on literature review and analyses, the repair methods can be broadly characterized as protective coating, electro-chemical methods, wrapping and encasement and partial replacement of steel. Also, methods to evaluate the repair materials and the repair configuration have been documented.IntroductionOne of the biggest challenges facing the aging infrastructure is the materials loss and deterioration due to corrosion. Many studies indicate that in the US alone, costs due to corrosion loss is more than $276 billion annually (Michiel et al., 2010). Corrosion is the major cause of deterioration of steel structures and components (MNC, 2005). Load bearing steel piles are used as foundations for various types of structures and hence corrosion is very much influenced by the environment such as soil, water and soil-water interface. Corrosion of steel pile foundations may result in reduced capacity in the axial and lateral directions. Hence, understanding the rate of pile corrosion is essential to select the appropriate repair methods to avoid excessive deflection and failure (Decker et al. 2008).To prevent the deterioration mechanisms that attack a pile, it is fundamental both to identify and understand the deterioration mechanism that has been the cause of damage. Understanding the deterioration mechanism allows the engineer to design a repair that will combat this type of damage. It is widely recognized that the corrosion of carbon steel in soil, water and soil-water interface proceeds according to the following simplified anodic reaction and cathodic reactions in the presence of oxygen (Decker et al. 2008)."

Jan 1, 2017

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By Thomas Trochalides

Newtown Creek Water Pollution Control Plant in Brooklyn, NY is the largest of 14 Water Pollution Control Plants in New York City. It services over 1 million people with a current processing capacity of 310 million gallons daily. Upgrades to the plant have been underway since 1998. This paper details the foundation elements installed in three separate contracts during 2009: NC-41F, NC-36G, and NC-47G. The elements are Concrete-Filled Pipe Piles, H-Piles, Steel Sheet Piling, Secant Walls, Drilled Caissons, and High Capacity Micropiles. Soils on the site consist of fill over organic silty clay and silty sand. Beneath the organic layers lie lake sand and varved silt and clay, sitting atop glacial till and rock. Due to Federal Mandates, certain plant capacity and secondary treatment requirements had to be met by specific dates. Failure to meet the requirements would have an adverse affect on the NYC areas being serviced. Further complicating the project, the existing plant operations had to be maintained throughout the entire construction phase. To accommodate the constraints of the project, new specialty equipment and several key redesigns were used to maintain construction schedules

Jan 1, 2010

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By C. M. Haberfield

"1 INTRODUCTION Around the world, there is a demand for larger structures, tall buildings and large bridges. While good footing design is important for all structures, it is even more important in the case of large structures. Recent experience with footing design for tall buildings (e.g. Burj Al Alam development and Nakheel Tower in Dubai, the Gate of Kuwait in Kuwait, the City Centre Project in Bahrain and Eureka Tower and Freshwater Place in Melbourne) has shown the benefits of investing in footing planning, design and construction (Haberfield, 2011, Poulos and Bunce, 2007). The footing systems for most of these projects include the use of deep bored piles or barrettes (piles of rectangular cross-section). Many use piled rafts where the piles, while acting to support the load, are primarily used to reduce settlements. A clear understanding of the factors controlling the behaviour of the footing system is needed to enable a good engineering design to be achieved. This starts with a sound understanding of the ground characteristics and individual pile performance, including adequate collection of data and testing. The best footing solution can then be found using recent improvements in data collection and analytical techniques, complex and highly capable computer-based models and the availability of high speed computers. This paper focuses on the axial performance of deep bored piles socketed into rock – both their individual performance and their performance as part of a larger footing system. Recent research and construction practice is discussed. In practically all cases, serviceability conditions control the behaviour of the footings. Methods of establishing the parameters for input into sophisticated computer programs are described. Application of the methods to case studies is included and it is shown that the behaviour of individual piles can be closely predicted. These developments lead to lower construction costs, better constructability and shortened construction time because of the better understanding of footing behaviour. 2 FACTORS AFFECTING PERFORMANCE OF FOOTINGS ON ROCK For a typical pile-supported footing, it is necessary to consider both individual pile, pile group and raft performance. These require consideration of the behaviour of the ground immediately beneath the surface raft or footing, along the pile shaft, and at and beneath the pile toe (Figure 1). Immediately beneath the surface raft or footing, the important factors are strength for bearing capacity and stiffness for settlement and interaction effects. Along the pile shaft, of most interest are strength for bearing, excavatability and stability; stiffness for settlement and interaction effects; geology and permeability for pile stability and, most importantly, pile shaft resistance. At the pile toe all the above factors for the pile shaft are present and in addition the pile end bearing is of interest. Below the toe, stiffness for pile settlement is important to at least a depth of twice the building width."

Jan 1, 1900

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By M. D. Riegel, Brian T. Felber

"Construction of foundation elements in an urban environment is often complicated by multiple constraints such as existing foundations, utility conflicts, maintenance and protection of traffic on high volume roadways, low overhead clearances, and vibration and displacement monitoring to reduce risks of impact to existing facilities. Micropiles are commonly a preferred foundation alternative in an urban setting to mitigate some of these risks. This paper presents examples in which micropiles helped reduce risk in an urban setting on the two subject infrastructure improvement projects. The case studies presented include the Verrazano Narrows Bridge HOV and Bus Ramp Improvements in Brooklyn, NY and the Kosciuszko Bridge Replacement in Queens and Brooklyn, NY. The paper details the micropile design, how risks were mitigated, and the complications to each of these projects associated with the urban setting.INTRODUCTIONThe paper begins with background information about the Verrazano Narrows Bridge HOV and Bus Ramp Improvements Project, followed by background information for the Kosciuszko Bridge Replacement Project. This introductory background information is followed by discussion of the urban site constraints, which controlled the foundation type selection for both projects. In closing, the paper discusses the micropile design process, load testing, and construction.VERRAZANO NARROWS BRIDGE HOV & BUS RAMP IMPROVEMENTS BACKGROUNDProject ScopeThe project consists of two new ramps; one designated for HOV / Bus traffic between Staten Island and the Gowanus Expressway, and one to be utilized for storing the barrier transfer vehicle. Also included is the complete reconstruction of Ramps B and F to accommodate horizontal and vertical alignment clearances from the new ramps, removal of the median of the upper level to add one lane, utilities improvements, stormwater improvements, and miscellaneous structural repairs. The new HOV / Bus Ramp was designed for reversible traffic flow to accommodate the demand of the peak traffic direction by movable barrier.Geotechnical / Foundation Engineering ScopeThe geotechnical work included a desk study review of existing plans, geotechnical reports, and geologic maps. This data was subsequently supplemented with a subsurface exploration program. Once completed, foundation design was performed for 25 proposed bridge substructures. Four existing battered pilesupported foundations and two shallow foundations were evaluated for increased loading. Upon completion of the foundation design, foundation plans, specifications, and an engineer’s estimate were prepared. Foundation installation was observed on a part-time as needed basis."

Jan 1, 2016