Search Documents

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Colin C. West

On August 7, 1986, Barge 45, while being towed near the mouth of the Niagara River, was swept downstream and pinned against one of the central piers of the Peace Bridge. The barge rested against the pier with 125 feet overlying the Canadian border and 50 feet overlying the American border. The tug boat which was towing the barge was lost further downstream. Fortunately, the crew escaped and were rescued with no loss of life. There was serious concern about the potential erosion effects of the river currents on the foundation of the bridge pier as caused by the flow concentrations around the barge structure. Due to the time of year, with the approaching Fall and associated worsening weather conditions, it was imperative that the barge be removed as soon as possible. Donjon Marine of New Jersey, the United States Navy's Atlantic Zone Contractor, was called on to retrieve the barge. By this time the original owner had abandoned the wreck.

Jan 1, 1987

By Anthony D. Barley

Over 60,000 multiple anchors have been used internationally since their introduction in the early 1990s, including 1000 in the United States. The multiple anchor system comprises a "multiple" of "unit" anchors installed within a single borehole - each unit anchor being staggered within the borehole length to mobilize its own capacity independently of the other unit anchors. These systems offer higher capacity than conventional anchors with identical bond lengths due to superior load transfer efficiency. The use of higher capacity anchors may allow reduction in the number of anchors required on a project, which results in time and cost benefits to the anchor installer, contractor, and the owner. Fully removable temporary multiple anchors are available, and have been used with consistent success. Three case histories are discussed highlighting the use of these systems

Jan 1, 2002

By Joram M. Amir, Ernst Niederleithinger, Nikolaus Schneider

"Abstract: Diaphragm walls are used to provide a stable and watertight confinement for the construction of tunnels, underground railway stations, deep basements and other structures requiring deep excavations. Water seepage and soil loss through the joints have occurred on several occasions, causing extensive damage. This may have been due to uncontrolled concrete flow between the joints, unexpected geologic conditions or just poor workmanship.Different ways of quality assurance are applied on construction sites. Most of them rely on recording parameters of the construction equipment and conventional concrete quality control. In the frame of the EUREKA/ZIM project DiWaQ we have looked at several ways to perform non-destructive quality control. Some methods are to be applied after excavation before concreting (phase 1); others after the wall is completed (phase 2).For phase 1 we have used two different principles for checking the shape of the excavation, especially the joint to existing panels. A mechanical device which can be adapted to the excavating equipment was developed; field tested and validated on test and construction sites. It is described in detail in another paper in the same volume. A sonar-based device with a 10 mm resolution has shown good performance in the lab, but is still under development.For phase 2 different temperature sensors have been lowered into access holes to monitor the hydration heat developed during concrete curing. The same tubes can also be used to perform electromagnetic and ultrasonic crosshole measurements across or along joints to detect flaws. Especially the ultrasonic method has shown promising results on validation specimen at the BAM test site at Horstwalde, but limitations as well. Success substantially depended on the joint type, flaw size and distance of the sensors to the joint."

Jan 1, 2014

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Samer R. Rabab?ah

As part of the PHX Sky TrainTM project at Phoenix Sky Harbor International Airport in Phoenix, Arizona, the existing traffic lanes at the 44th Street underpass below the Union Pacific Railroad (UPRR) Bridge will be shifted to accommodate the people mover guideway. The proposed reconfiguration and reconstruction of 44th Street required the utilization of micropiles and permeation grouting to resist the lateral forces induced by cutting into the slope below the existing bridge abutment footing. This paper discusses the evaluation of the existing bridge abutment, including analysis of the original foundation system, and design, installation and testing of a new micropile-supported retaining wall to support the cut slope below the existing bridge abutment foundation. A monitoring program was implemented during construction to evaluate the short- and long-term performance of the bridge abutment. Instrumentation included survey monitoring points, inclinometers, tiltmeters and crack gauges. A micropile load testing program was conducted to verify design assumptions concerning micropile axial and lateral loading. Numerical analyses (using PLAXIS software) were performed to predict the short- and long-term behavior of both the abutment wall and the bridge foundations. Movement data collected from the monitoring program indicate that the wall and bridge foundations are performing satisfactorily and within the general bounds of predicted movements. The results from the numerical modeling using PLAXIS software showed that the proposed solution is deemed adequate to provide the needed global stability with an acceptable factor of safety, along with acceptable deformation.

Jan 1, 2011

By E. Stoetzer

In all known deep mixing processes the existing soil is mixed with self hardening slurry by mixing tools that rotate about a vertical axis (augers, mixing paddles). Wall panels are constructed using sets of multiple mixing tools combined into a single unit. These techniques have been developed on the principle of the rotary drilling technology. In contrast, the new Cutter Soil Mixing or CSM technique is derived from the cutter technology. The soil is loosened and broken down by cutter wheels, then mixed in-situ by the rotating cutter wheels with the self-hardening slurry - introduced into the ground between the two wheels - to form a soil-slurry mortar. The main area of application lies in the construction of cut-off and retaining walls.

Jan 1, 2006

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Cory G. Rice

A significant portion of the piling industry has long felt relying on soil setup to gain the required capacity is a complexity that would rather not be dealt with. Instead, the pile are driven to the required capacity on the initial drive and the potential gain of capacity due to soil setup is simply considered an added bonus or safety factor. There appears to be an attitude that if one did not put in the energy required to develop the full capacity on the initial drive, then one should not expect to gain anything from Mother Nature for free. However, substantial savings in time and materials can be realized by properly accounting for setup. This paper will show the impacts and ramifications this rationale can have on required labor and material costs and illustrate a case history with significant soil setup and the savings realized on a project currently being constructed.

Jan 1, 1992

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002