Search Documents

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By Moi Arzamendi, Jose Ramirez, Kenneth Kniss, Sunil Arora, James Gingery

Construction of a new approach embankment for a railroad bridge over a river in Southern California required placing up to 12 ft of fill over soft to medium stiff silts and clays along an approximate 1,500-ft long stretch. The embankment, situated within a narrow railroad right-of-way between an existing live track and existing buildings, would have been susceptible to excessive settlement that could damage existing buildings and numerous underground utilities if regular weight soil fill had been placed over the unimproved ground. To limit total and differential static settlements to tolerable levels, a design was developed using a combination of mechanically stabilized earth wall with lightweight cellular concrete fill and rigid inclusions ground improvement. This paper describes the design of the ground improvement system, construction methods used, and challenges of working next to live railroad traffic. Ground improvement quality control and assurance measures, and verification of performance by settlement monitoring are also addressed. INTRODUCTION AND BACKGROUND The 0.9-mile San Diego River Double Track (SDRDT) project is located on the Los Angeles-San Diego- San Luis Obispo (LOSSAN) Corridor in San Diego, California. The project includes the replacement of the existing 900-ft long single track railroad bridge over the San Diego River with twin double track structures. Construction of the project is phased and closely coordinated with the associated Mid-Coast light rail project (San Diego Trolley Blue Line Extension). The new bridge is a 7-span, twin steel, through girder structure supported by six cast-in-place reinforced concrete pier caps and two abutments. The large diameter cast-in-drilled-hole (CIDH) foundations are up to 9 ft in diameter, with upper portions encased in a 1.5-in.-thick permanent steel casing. The north abutment approach embankment includes a mechanically stabilized earth (MSE) retaining wall up to approximately 10 ft high and 1,520 ft long. This paper focuses on the design and construction of the north approach embankment. The project site is characterized by challenging geotechnical and seismic conditions. The site contains liquefiable soils interbedded with soft cohesive soils, underlain by competent layers of sand/gravel/cobble and other sedimentary formations. Static settlement of the new railroad, crossing utilities and adjacent buildings was a primary design concern for the north approach embankment.

Jan 1, 2018

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft's capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By Patrick E. Durnal

A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM Harris) designed the $779 mill seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofit was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with support of various consultants.

Jan 1, 2013

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By Ekhlaq A. Khan

"The new third Bridge over Narmada River at Bharuch which was recently completed is characterized by some aesthetically appealing elevations of the pylon and large size of the deck. This paper gives an insight to design and construction technique adopted for foundation construction of Extra-dosed span - 3 rd Narmada Bridge at Bharuch over river Narmada, Gujarat. Site being located in intertidal zone had its unique geological characteristics and own set of difficulties during construction.INTRODUCTIONThe Indian subcontinent offers diverse subsoil conditions. With current modern and future trend of long span bridges the substructure design often demands large size foundations. The foundation of theses bridges are usually deep and large in size. The execution of such foundations in maritime environments often involves important temporary works, in order to provide a safe workplace, comply with environmental requirements and achieve high quality standards.Often Pile foundations are preferred solution now a days, but due to various statutory and environmental regulations their construction poses a challenge. With better equipment and corresponding quality control, construction of large diameter pile foundation has emerged as a faster and reliable option.OVER VIEW OF THE PROJECTThe first two lane bridge on NH-8 (Vadodra – Mumbai) known as Sardar Bridge was constructed in 1977, subsequently an additional two lane bridge was constructed in 1999-2000, 29 m downstream of the first. In view of rising volume of traffic and as part of upgradation of NH8, National Highways Authority of India (NHAI) proposed to construct 3rd new 4 Lane Bridge 100 m downstream of 2nd Narmada Bridge, based on Central Water and Power research Institute (CWPRS) study and recommendation.The general layout (fig. 1) of the 3rd Narmada bridge has 8 spans of 144 m and 2 spans of 96 m with total length of 1344 m, supported by132 nos. of 1.5 m diameter piles of about 50 m depth. The substructure has leaning “Y” shaped lower pylon of height 30 m together with cast in situ pier diaphragm. The piles are of M40 and superstructure & pylon of M50 grade of concrete."

Jan 1, 2017

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Gustavo E. Armijo

This job was done in Morristown, NJ, with mono fluid system jet grouting for the construction of a new bank building. After the demolition of the existing two story structures, an excavation in loose sandy fill materials was necessary in order to reach the new structure basement level. Due to this jet grouting was selected as a medium to provide both excavation support and permanent underpinning, minimizing the adjacent building settlements. These two adjacent buildings were partially underpinned with a "gravity wall" made with 2 and 3 rows of secant vertical and inclined jet grout columns. Besides the classical jet grouting control methods, during the jet grouting execution, all the drilling and grouting parameters were recorded by a proprietary system called "Slogger". Additionally, after the jet grouting execution, an innovative result control technique was used by means of the application of the same parameter recording system. Some of the production columns were re-drilled and a comparison was made between the obtained drilling parameters and those obtained for the same age test columns. Under the referred existing conditions and in comparison with the conventional underpinning techniques, this project demonstrated that jet grouting, with proper execution and result control, can be faster than them and can maintain the building structural stability and act, at the same time, as a retention system minimizing the existing building settlements.

Jan 1, 2002

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Vasileios A. Drosos

The response of pile foundations to lateral loads is an important factor for the successful performance of several critical structures. A new numerical code for the analysis of single piles under lateral load is outlined. The code can simulate (through appropriately chosen parameter values) not only the non-linear behavior of soil, but also the inelastic structural response of the pile itself under lateral load. Emphasis is given on the calibration of model parameters and the verification of the code. For the calibration of the parameters, data is used (a) from the well documented in the literature p-y curves, and (b) from experiments conducted either in full scale or in the centrifuge. Results are compared to those of well known published codes for inelastic analysis of single piles under lateral load.

Jan 1, 2006

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989