Search Documents

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By Philippe Portella

Current Ownership : AREVA NC-France & affiliates (63.4%), ONAREM-Niger (36.6%)Related Mines : Ariège, Artois, Arlette(initial Somaïrlease) and Tamou, Taza, Takriza, Tamgak(SMTT lease)Mining Method : Open Pits Reserves : about 14 000 tU Average grade : 0.3 % UEnvironmental Management : Certified ISO 14001 since November 2002Key figures :2003 output : 1126 tU number of employees at year end : 565 Current Ownership : AREVA NC-France & affiliates (34%), ONAREM-Niger (31%), OURD-Japan (25%), ENUSA-Spain (10%) Related Mines : the Akouta mine provides access to several adjacent orebodies(Akola, Akouta, and coming Afasto with Ebba North / South)Mining Method : Underground ?mainly room & pillars Reserves : about 29 000 tU Average grade : 0.40 to 0.50 % U3O8Environmental Management : Certified ISO 14001 since January 2003Key figures :2003 output : 2017 tU number of employees at year end: 1070

May 1, 2006

By G. Harper

The Sustut Copper deposit, 230 miles northwest of Prince George, B.C., was discovered in August of 1971. Subsequent exploration has included 56,417 feet of surface diamond drilling in 139 holes. The deposit occurs in gently dipping volcanic rocks of the Upper Triassic Takla Group, which outcrops as rugged mountains. The general Mesozoic sequence comprises some 20,000 feet of green and red basaltic to andesitic rocks. The Lower Formation is characterized by subaqueous basalt, andesite and augite porphyry flows with interbedded breccias. They were rapidly deposited in tectonic depressions of limited extent and steep gradients. Fades changes are abundant. The Middle Formation consists of volcaniclastic rocks made up of fragments from the underlying formation. Two cycles are discernible, both with basal turbiditic, tuf-faceous sandstone and shale units overlain by massive, volcanic conglomerates exhibiting graded and cross bedding. A broader, shallower-water basin is indicated. The top of the uppermost unit was subaerially deposited. The Upper Formation is a variable sequence of volcanic sedimentary rocks. Detritus was supplied from a wide source area and included multiple reworked fragments of the lower formations and material from other rock groups known in the region. Zeolite fades metamorphism is recognized throughout the entire sequence. Epidote is particularly abundant in the Middle Formation, demonstrating the results of metasomatism. The mineralized zone is approximately concordant with the strata over 100-200 feet of the Middle Formation succession. It lies just below the zone of transition from subaqueous to subaerial deposition in the top unit. Hematite, chalcocite, pyrite, bornite, chalcopyrite and native copper are disseminated throughout all sizes of lithic fragments and matrix. Concentration into the specific zone is believed, to be due to upward leaching of copper during low-grade metamorphic and metasomitic reaction. Precipitation occurred in the zone of hydration characterized by prehnite-pumpellyite below the oxidized subaerial rocks.

Jan 1, 1977

By D. F. Sangster

"Eight volcanogenic massive sulphide districts in Canada and Japan, ranging in age from Archean to Miocene, were selected for analysis. The study revealed that: {I) each district has an average diameter of 32 km; (2) the districts contain 4 to 20 deposits each, with an average of /2 deposits; (3) the average total base metal content per district is 4.6 million tonnes, with a coefficient of variation of32%; (4) ranked in order of size, the largest deposit in each district contains, on average, 67% of the total metal and the second largest about 13 %. The remaining deposits range downward in decreasing proportions. Empirical observations such as these may be used f or evaluating the undiscovered potential of new districts as well as contributing to a better understanding of the distribution and genesis of this important class of base metal deposits. Previous WorkThe characteristic geological features o f volcanogenic massive sulphide deposits have been described by numerous authors over the past fifteen years and it is now widely accepted that these deposits comprise a major ""deposit-type."" In addition to these geological parameters, however, it is now becoming apparent that volcanogenic massive sulphide deposits show several distinctive grade-tonnage relationships. For example, Singer et al. (1975) demonstrated a slight negative correlation between copper grade and ore tonnage in their sampling of 146 volcanogenic deposits. In a study of 110 Canadian Precambrian deposits of this type, Boldy (1977) showed that the size of the modal deposit is 0.39 million tons, that of the median deposit is 1.40 million tons and the arithmetic average is 6.85 million tons. Moreover, Boldy's data show that the average grade of combined base metals (Cu + Zn + Pb) for each of the se three deposit-sizes is, respectively, 6.25%, 5.35% and 6.47%. Because the lead content of Canadian Precambrian volcanogeni c deposits is most frequently less than 1%, the total metal grade is effectively Cu + Zn . From Figure 2 in Bold y (1977), it can be seen that 83% of the deposits fall in the range of 0.l to 10 million tons ."

Jan 1, 1980

By Claudia Gasparrini

"Silver occurs in about 200 minerals in variable amount s. Silver ores usually have 5 or 6 and in some instances as many as 10 species of silver minerals. All these minerals may have different flotation and leaching properties and should be correctly identified for successful recoveries. Grain size and host minerals which are critical in gold recovery, are not always as important for silver minerals.IntroductionMineralogical factors affecting the metallurgy of silver are , as for other metals: (i) the silver-bearing mineral s ; (ii) their grain size, and when dealing with very fine sizes; (iii) their host minerals; and (iv) the association they form with the silver-bearing minerals. Of these, the silver-bearing minerals are more often the cause of problems during recovery as opposed to gold whose metallurgy is generally more affected by grain size and host minerals. The problems derive mainly from the complexity of the silver mineralogy: over 200 minerals exist bearing the element in major, minor and variable amounts.As a member of group I-B of the periodic table, silver forms extensive so lid solutions with the other two elements in the same group , copper and gold. It combines with sulphur, tellurium and selenium in covalent bonds and with chlorine, bromine and iodine in ionic bonds. Where the fluid composition, temperature and pressure during crystallization allow it, silver also combines with arsenic, antimony, lead, bismuth, tin, mercury, indium, thallium, and germanium in many instances as a minor element in sulphide , sulphosalt and native element minerals. Cations which silver replaces to a lesser extent than copper and gold are iron, manganese, zinc and probably nickel and cobalt."

Jan 1, 1984

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By T. H. North, A. G. Glover, R. J. Pick

"Girth welding operations represent the rate-limiting step in pipeline construction. A joint industry-university program was set up to establish the field welding characteristics of large-diameter, high-strength line pipe.Theoretical work carried out at the University of Waterloo showed that pipe wall thickness and joint misalignment prior to welding has a marked influence on the lifting stresses acting on the root pass of girth welds. Pipe diameter and pipe ovality had negligible effects. Super-position of lifting and residual stress (caused by the fusion welding operation) highlighted regions of the weld bead most susceptible to hydrogen-induced cracking.The field welding characteristics of 1219-mm-diameter, 13.72-mm-wt Grade 483 line pipe were evaluated using a specially designed test rig. The principal test variables were lift height, delay time after root pass deposition, preheat temperature, pipe composition and joint misalignment prior to welding. For any given life, preheat and joint misalignment prior to welding had the most significant effect on cracking tendency.The output of this program has industrial significance and illustrates the beneficial features of university-industry collaboration.IntroductionField welding operations comprise the rate-limiting step during pipeline construction. Crack-free girth welds must be made in a wide range of weather conditions and consequently the field weldability of line pipe compositions directly affects pipeline integrity and construction economics.Pipe-laying practice comprises root bead deposition followed by a skidding operation involving lifting (or lowering) the pipe length onto skid s so that the next pipe length can be aligned prior to welding. Consider pipeline construction using 24.4-m lengths of 1219-mm-diameter , 13.72-mm-wt Grade 483 pipe weighing approximately 10,000 kg. Skidding involves loading a 3-mm-thick root bead by moving the free end of the pipe through vertical distances of up to 700 mm . The likelihood of cracking in these circumstances depends on the inherent crack susceptibility of the pipe composition employed, on the hydrogen content of the deposited weld metal and on how well the joint handles the external stressing caused byskidding."

Jan 1, 1981

By G. Pouskouleli, T. A. Wheat

"The role and benefits of using statistical methodology in the development and optimization of materials and processes is examined. It is shown that considerable benefits accrue from the use of an appropriate design in which a number of factors (process parameters) are varied simultaneously while the system response such as percent recovery, degree of separation, purity, etc. is monitored and ultimately optimized.Compared with the commonly encountered one-factor-at-a time approach, this schema exploits reduced experimentation (thereby requiring reduced resources [staff, time, dollars, etc.]) yet yields quantitative information on the significance of each factor and their combinations on the measured response."

Jan 1, 1992

By Michael J. Lawrence

"The VALMIN Code was developed and formally adopted by The Australasian Institute of Mining and Metallurgy (AusIMM) in 1995 and a revision was issued in 1998. The VALMIN Code applies to all relevant reports under the Australian Corporations Law, including submissions to the Australian Stock Exchange (ASX) and the Australian Securities and Investments Commission (ASIC).The VALMIN Code and Guidelines sets standards for the preparation and commissioning of independent assessment and/or valuation reports on mineral and petroleum assets or mineral and petroleum securities.It is mandatory for AusllvI:M's members to follow this Code in these relevant circumstances and failure to do so will result in serious sanction of the member by the Ausllvllvfs Ethics Committee. Public support for the use of this Code has been given by regulators (ASX/ASIC) and market participants ( eg major accountancy firms). It is also endorsed as a guide to general best practice in project assessment and valuation.This paper will discuss how the VALMIN Code has worked in practice over the past few years. It will also examine areas where the Code could be improved and how it could form the basis of a new Canadian Code for mineral property valuation."

Jan 1, 2003

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

By Patrick J. Williams

Defining Features of IOCGs ? Sulphur-poor Cu-Au(-Fe) deposits ? Contain low-Ti iron oxides ? Hydrothermal origin (breccia, vein, replacement) ? Local structural controls (no ?causitive? intrusions) Common Features (Economically-Significant Terranes) ? Regional space-time association with plutons ? Association with widely metasomatized crust ? Na ? Na-Ca ? K ? Variable enrichment in F, Co, Ba, LREE, U ? Little hydrothermal quartz (cf. porphyry deposits)

May 1, 2006

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By K. Woo

"With ever-increasing global demand for mineral resources, mining companies are considering developing deeper, more complex and lower grade ore bodies. Recent years have seen the transition from surface to underground mass mining operations to access deeper resources, with mass mining methods such as block and panel caving being favoured due to the tonnages and economics achievable when dealing with lower grade ore. However, the rock engineering interactions involved with such plans are complex and challenging given the significant disturbance caused to the surface environment. If not properly accounted for, the unexpected propagation of a cave breaking through to surface or the differential surface displacements otherwise produced may threaten the safety and integrity of overlying mine and civil infrastructure.This paper reports the findings of a comprehensive research programme focussed on investigating and integrating new developments in remote sensing characterization and monitoring technologies with state-of-the-art numerical modelling to better manage the challenges and geo-risk associated with the transitioning from open pit to underground mass mining. Procedures were developed to integrate discrete fracture networks (DFN) into finite-element/discrete-element analyses to simulate the influence of rock mass fabric on cave propagation and the evolution of caving-induced surface subsidence and step-path failure of large open pit slopes through the progressive failure of rock bridges. The results clearly showed that caving-induced surface deformations tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Although parallel investigations of empirical design charts used to predict caving-induced deformations were found to be moderately sufficient for assessing the extent of macro deformations directly above the undercut (i.e. caving collapse features), numerical modelling was found to provide the only means to confidently estimate the lateral extent of smaller strain subsidence.These results were further supported by the use of high-resolution synthetic aperture radar (SAR) data to monitor the ground deformations associated with block caving production, and to use these to calibrate and constrain a series of predictive 3-D numerical models focussed on Rio Tinto's Palabora mine in South Africa. The InSAR data was obtained from Canada’s recently launched RADARSAT-2. The close fit achieved between the predictive 3-D numerical model and InSAR monitoring data demonstrates the significant value of InSAR calibrated 3-D numerical models applied to subsidence prediction.Collectively, the results from this research programme have helped to further the characterization, assessment and understanding of mass mining-induced subsidence, and its evolution, by addressing existing limitations in the use of empirical and numerical design methods. The limitations and uncertainty arising from mine site data were detailed, specifically the representation of mine geology, rock mass properties, in-situ stresses and cave propagation, together with means to constrain these inputs and calibrate sophisticated 3-D numerical models through back analysis and integration with high resolution monitoring data."

Jan 1, 2015

By N. D. MacFarlane, D. J. Mossman

"The Nemeiben Lake ultramafic complex, in the Churchill Province of the Canadian Shield in north-central Saskatchewan, is a small I. 6-km circular plug largely composed of high-alumina pyroxene cumulates forming a series of grossly concentric layers of clinopyroxenite, websterite and wehrlite. Minor dunite and gabbro are present in the northwestern part of the pluton.Disseminated primary magmatic pyrrhotite, pentlandite, chalcopyrite, magnetite and chromite occur throughout the intrusion. Sulphides occur in proportions of economic interest in the northern outcrops. A secondary assemblage of fine-grained oxides, sulphides and native metals occurs in serpentinized and uralitized peridotites and pyroxenites. Primary opaque minerals are largely altered to marcasite, violarite and hematite. The ores represent a primary magmatic assemblage extensively modified by metamorphism and, to a lesser extent, by supergene alteration.The complex intruded an Early Aphebian supracrustral succession during the waning stages of the Hudsonian orogeny. The metamorphic peak during Hudsonian time reached middle to upper amphibolite facies, granitized the country rocks and contributed to the partial amphibolitization of the ultramafic pluton.The Nemeiben complex has a number of features in common with the zoned intrusions of southeastern Alaska, including: the diopsidic composition of clinopyroxene, highly magnesian olivines, ubiquitous primary magnetite, relatively high alumina content of clinopyroxenes and the unlikelihood that associated gabbroic rocks are derived from a magma common to the ultramafic rocks. However, at Nemeiben, orthopyroxene occurs as a widespread postcumulus phase and, to a lesser extent, as a cumulus mineral. This fact, together with geochemical data on whole-rock and mineral compositions, indicates a tholeiitic parentage.The nickel-copper deposits of the Nemeiben Lake ultramafic complex are not currently economic, although standard technology for recovery of sulphide minerals in the clinopyroxenite (and websterite) would probably be adequate. Most ore minerals in the altered peridotites belong to the fine-grained secondary assemblage of opaques due to the formation of retrograde hydrous silicates and are probably too fine grained for standard recovery methods."

Jan 1, 1982

By Francis Breton, Lei Pan, Kun Liu

"Effects of Fe, Cu and Mg minor alloying elements on creep properties of 8xxx aluminum conductor alloys were investigated by conducting compressive creep tests at 100 ºC under a constant load of 69 MPa. The microstructural evolution was studied using an optical microscope and electron backscatter diffraction technique. The creep properties were characterized by the primary creep strain in the first stage and the minimum creep rate in the second stage of creep deformation. Results showed that additions of all three minor alloying elements (Fe, Cu and Mg) demonstrated a beneficial effect on the creep resistance but individual alloying elements exhibited different impacts on creep properties. The additions of Fe and Mg showed a strong impact on both the primary creep strain and minimum creep rate, while the Cu addition displayed a favorable effect on the primary creep strain but no impact on the minimum creep rate. Microstructure observation revealed that with increasing Fe contents, the volume fraction of fine intermetallic dispersoids gradually increased while the subgrain size and misorientation angle became smaller, providing strong barriers to the dislocation and grain boundary movements. The addition of Cu moderately reduced the subgrain size and misorientation angle and in combination of solid solution strengthening it promoted the retardation of the creep deformation during the primary stage.INTRODUCTIONThe 8xxx aluminum conductor alloys offer significant advantages such as low density, high conductivity to weight ratio and low price over copper conductors and become an attractive candidate in electrical engineering and building wiring (McQueen, Chia, & Starke, 1986; Birol, 2009; Engler, Laptyeva, & Wang, 2013). The mass resistivity of aluminum conductors is one-half of copper conductors. Thus, only one-half the weight of aluminum is required for equivalent capacities. Therefore, this unique property coupled with a relatively low price of aluminum offers significant economic advantage to develop aluminum conductor alloys for electrical applications in the electrical wire industry."

Jan 1, 2016