Search Documents

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By A. Robles-Vega

Personnel of Mexicana de Cobre, a subsidiary of Southern Copper located in Nacozari, Sonora Mexico have been working in the past few years on the development of a process to treat and manage, in an environmentally accepted practice, the residues and effluents generated during the process. To date, this team has been reviewing existing technologies and also has explored new alternatives. At the end of this phase, a novel, efficient and complete process has been configured which will be able to treat some solid and liquid streams such as Teniente converter dust, Peirce Smith converter dust, a Sb-rich precious metals slag, copper refinery electrolyte bleed, acid plant blowdown and an acid bleed of the precious metals plant. The process will consist of a leaching stage, followed by a very selective copper precipitation using novel technology which has been named as back reactions. After copper precipitation, impurities (As, Sb and Bi) will be precipitated mainly as arsenic trisulfide (As2S3) using H2S(g) which will be generated by means of a new process developed in our company. At the end of the process, small volumes of arsenic trisulfide will be vitrified and then disposed as a stable residue.

Jan 1, 2007

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By P. Belley

Prior to 2006, the filtration unit for leached sludge treatment (filter press) permitted the filtration, washing and drying of cake to 17% (w/w) moisture. That year saw moisture content abruptly increase to 20% (w/w), drastically changing the rheological properties of the cake. The cake became sticky and agglomerated. This led to major disruptions of operations and plant capacity (cake release and cake conveyor problems, complicating the subsequent steps of the process). The conditions for the filtration, washing and drying, were simulated to ease cake unloading without aggravating dust emissions (moisture about 17% (w/w)). All of the laboratory tests yielded a moisture content above 17% (w/w). Therefore, we concluded that the moisture problems were not due to a recipe change in primary material, but to an operational problem in the filter press. Through the laboratory results, the filter press operating conditions (washing ratio, drying pressure and drying time) were optimized to enable a reduction in cake moisture to 17% (w/w).

Jan 1, 2007

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By T. V. Lord

Minerals containing uranium have been successfully pre-concentrated by flotation at Queen's University, Kingston. In particular, uraninite, uranothorite, euxenite, and fergusonite, have responded to flotation to yield grades of 0.2 to 6.0 .per cent U .o. with recoveries of 85 to 98 per cent, from heads analysing approximately 0.10 per cent U3Os. Of the ten or so radioactive samples examined to date, two distinct groups were recognizable, firstly, those samples in which uranium was the sole constituent of economic interest, and, secondly, those in which Columbium (with minor amount of tantalum) was present in addition to uranium. For the purpose of this paper, the results of investigation on two samples of each of the above groups have been selected as typical.

Jan 1, 1945

By J. Grant Spratt

THE Turner Valley gas-field, situated some thirty miles southwest of Calgary, Alberta, has been the topic of much discussion, particularly from a geological viewpoint. Several papers (1, 2, 3, 4, and 7) dealing with the structural and stratigraphical geology have already been published and are available for reference(l). In this article, the geological conditions will be treated only as they directly refer to the crude-oil prospects along the west flank of the anticline. HISTORY During the past twelve years, Turner Valley has been known mainly as a field which has produced a high-gravity naphtha from relatively large quantities of gas. For about ten years prior to the discovery of this naphtha-bearing gas, which is produced within the upper 450 feet of a dolomitic limestone of Carboniferous age, a minor production of light crude-oil was obtained from overlying sands of Cretaceous age. Up to June 1st of the present year, the field had produced 9,473,582 barrels of naphtha from approximately 829,000,000 M.c.f. of gas. For the past four years, the total daily production of 80 to 90 wells has averaged about 3,200 barrels of naphtha from 250,000 M.c.f. of gas. This is an average of 13 barrels per million cubic feet. The naphtha is extracted from the gas by ordinary gas-oil separators and absorption plants. After the naphtha has been recovered, about ten per cent of the gas is marketed for fuel to supply the cities of Calgary and lethbridge and intermediate cowns. The remaining ninety per cent is burned to the atmosphere, with the exception of some four to five million cubic feet per day which the Calgary Gas Company score in the depleted Bow Island gas-field.

Jan 1, 1936

By Staff

Introduction The Hedley mine, perhaps better known as- the Nickel Plate mine, is one of the outstanding properties of southern British Columbia. Discovered in 1898 by Woollison and Arundell, prospectors, the property was bonded in 1899 to M. K. Rodgers for the Marcus Daly Estate, of Butte, and development was started the same year. From the high grade of the ore outcrop, and its colour, due to oxidation of the arsenopyrite, it was not difficult to open up and trace the showing. The Nickel Plate ore-shoot, which apparently had been easy to follow on surface, was more difficult to trace underground. In 1903, prospecting on an adjoining property, the Sunnyside, showed commercial ore at surface, but it was only after two years' work that the ore-body was defined and shipments started. From this property, $1,200,000 have been taken out. Prospecting was also carried on on the IXL, Climax, Copper Cliff, Mound, Bulldog, Exchange, Silver Plate, Gold Plate, and other properties, all of which had surface showings, but up to date only the Nickel Plate, Iron Duke, Morning, and Sunnyside have produced commercial ore. In 1904, the Bulldog looked like a very promising mine, but it failed to make good. In 1905, the Sunnyside No. 1 was in the limelight, but it also failed to make the grade. In 1906, an outcrop on the Sunnyside No. 3 looked interesting. Subsequent work. on this claim produced $840,000, and at the same time ore which yielded $400,000 was mined from the Sunnyside No. 4. In 1908, the Nickel Plate ore-body entered a lean zone and, as the diamond drill failed to give satisfactory results, the Daly Estate, after making a profit of $1,151,000, sold the property to the Hedley Gold Mining Company, Limited, for $760,000, retaining, however, a large interest.

Jan 1, 1929

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By C. J. Brown

Regeneration of hydrochloric acid steel pickle liquors has traditionally been accomplished by pyrohydrolysis. However, a number of factors have recently conspired to reduce the attractiveness of this approach. Moreover, the process is not amenable to small-scale operations. On the other hand, the standard technique for regeneration of sulfuric acid pickle liquors, which is the low-temperature crystallization of ferrous sulfate is applicable to any size operation. A similar technique has recently been developed to regenerate hydrochloric acid. Sulfuric acid is added to the ferrous chloride-bearing spent HCl pickle liquor. The temperature is then reduced to below 0°C, resulting in the crystallization of ferrous sulfate heptahydrate and liberation of free hydrochloric acid. Depending upon the crystallization temperature, variable concentrations of sulfate are left in the regenerated acid. Although this residual sulfate has an impact on the pickling characteristics of the regenerated acid, tests have shown that by adjusting the conditions, pickling rates will be at least equal to those using pure HCI, and an acceptable surface finish will be produced.

Jan 1, 2006

By Alex Matheson, Nick W. D. Massey, Peter T. Bobrowsky

Crowing pressures on aggregate resources include diminishing reserves, high transportation costs, sterilization and land use conflicts. In the absence of detailed resource knowledge for a particular region, aggregate resource potential maps provide the best "first approximation" regarding the surficial distribution of sand and gravel. The 1:50 000 scale Level Ill aggregate potential map integrates several important factors which influence the management of sand and gravel. Data used to generate this type of thematic map is readily available in most areas, fieldwork required is minimal, there is a logical quantitative evaluation of the data layers and integration is easily accomplished on a desktop PC-based platform. Also the aggregate potential map, with its focus on identifying areas of potential future aggregate exploitation as well as present inventory, provides a useful tool for the aggregate explorationist.

Jan 1, 2001

By C. A. Morais, L. V. Resende

"The technological development observed in recent years has stimulated the application of rare earth (RE) elements. Amongst their various applications it is well worth mentioning their use in electronics, superconductors, nuclear medicine, as well as in special inks - as those used in radar invisible airplanes. TV and computer monitor screens present as coating a powder containing some rare earth elements, mainly Europium and Yttrium. The recovery of the RE elements from electronic scrap is extremely important as the economic and environmental issues are concerned. This paper describes the study of the Eu and Y recovery from e-scraps. The first step of the process was the leaching of the powder obtained by manually scraping the inside surface of the screen. After the optimization of the leaching, the dissolution of Eu and Y was higher than 98 w/t% and a pregnant sulfuric liquor containing 11.9 g L-1 Y and 0.72 g L-1 Eu was obtained. The second step was the separation of the metals found in the liquor by the solvent extraction technique. The separation of Eu and Y was carried out in a counter current circuit compound of 3 extraction stages, 7 scrubbing stages and 15 stripping stages. DEHPA was used as the extractant, whereas a diluted sulfuric acid solution was applied as scrubbing agent and a hydrochloric acid solution at high concentration was used as the stripping agent.INTRODUCTIONThe rare earths (RE) are a moderately abundant group of 17 elements composed of lanthanides, scandium and yttrium. Amongst the RE, promethium (Pm) is extremely rare, however several of the RE elements are not very rare and occur dispersed in a variety of forms (Greenwood & Earnshaw, 1984; Tyler, 2004).The innumerable applications of the RE elements are based on their particular properties, mainly their spectroscopic and magnetic properties (Martins & Isolani, 2005). The technological development observed in recent years has stimulated the application of rare earth (RE) elements. They have been used in agriculture, electronics, superconductors, nuclear medicine, automobile industry, special inks – as those used in radar invisible airplanes, X-ray screens, high intensity mercury vapour light bulbs, neutron scintilators, charged-particle detectors and optical memory reading systems (Maestro & Huguenin, 1995; Nagaosa & Binghua, 1997; Sánchez et al., 1999)."

Jan 1, 2012

By P. Maltais

Over the last 10 years, Computer Aided Design, Finite Elements Analysis and field testing of prototypes have enabled the cycling industry to grow and to significantly improve its products. However, today's cyclists have become more and more demanding, making these classical design approaches almost obsolete. Devinci understood that problem four years ago and fully revisited its design approach; to offer bicycle frames better suited to real life riding, one must fully know those real life conditions. In partnership with the University de Sherbrooke, Quebec, Canada, Devinci then developed a bicycle enabling them to measure the actual load applied on a bicycle frame in real-time for real riding conditions: the instrumented bike. Today, Devinci uses its instrumented road and mountain bikes, combined with virtual prototyping and laboratory testing capabilities to develop better bicycles, faster.

Jan 1, 2006

By W. E. Cockfield

This paper is not intended as an original contribution to this subject, but rather as a review of the main theories which are held with regard to placer deposits, with, of course, particular reference to the placers of British Columbia. The present interest in gold mining has, however, brought the subject of placers to the fore, and possibly a brief outline of the geology of such deposits will serve as a basis for discussion on the subject. In Canada, the most valuable of our placers are deposits of gold, and consequently the discussion will centre largely on placer-gold deposits. The same principles apply, of course, to placer deposits of other metals. The Origin of Placer Deposits As a starting point, the idea which is prevailingly held is that placer or alluvial gold is detrital in origin, that is to say, the gold originally existed in veins, lodes, or disseminations in the country rock of the regions in which the placer deposits are now found, and that, through the various erosive forces of nature, it was liberated from those veins or lodes and concentrated in the form in which we now find it. 1 have not time to go thoroughly into the proof of this, but the lines of evidence are many. If we take the Cariboo district as a typical example, Johnston and Uglow(l) have shown, first of all, that the placer and vein gold are identical in character. Crystals occur both in the placers and in the lodes, but the crystals in the placers are nearly always slightly worn, indicating transportation.

Jan 1, 1932

By D. Atkinson

"Porphyry molybdenum-tungsten mineralization on the east flank of Hudson Bay Mountain crops out over 5 km2 and is intersected to depths of 2 km. Features such as a hornblende-biotite aureole, mineralogical zoning and dike, vein and fracture geometries within lithologies of the Middle to Lower Jurassic Hazelton Group and Cretaceous Skeena Group reflect an intrusive complex, the Upper Cretaceous to Early Tertiary Hudson Bay Mountain stock which has been intersected by drill holes. The stock is believed to be the mineralizing agent. A southeast-dipping granodiorite sill has been outlined by drilling within the Hazelton Group. Molybdenite and scheelite veins cut all rock types; however, the granodiorite sill hosts a higher density of fine-grained, banded, quartz-molybdenite and pegmatitic quartz-molybdenite veins reflecting a competency contrast between the intrusive sill and other country rock. Due to the relative abundance of these veins, grade is higher within areas of the sill. Above the 15000£ cross-cut 20.6 million tonnes grading 0.401% MoS2 and 0.041% W03 have been defined. During exploration of the deposit sampling procedures had to be adjusted because of the nugget effect attributed to drill intersections of banded and pegmatitic veins.IntroductionMolybdenite was discovered in outcrop at the foot of Kathlyn Glacier on Hudson Bay Mountain and first reported by the Geological Survey of Canada in 1944. The deposit has several names: Hudson Bay Mountain or Glacier Gulch, both after its location, and Yorke-Hardy after the original staker.The deposit is on the east flank of Hudson Bay Mountain, 9 km northwest of Smithers, west-central British Columbia, within NTS area 93L/14 (54° 49' North, 127° 18' West, Fig. 1). Hudson Bay Mountain, on the southern edge of the Bulkley Valley, is a dominant topographical feature reaching 2590 m elevation. Mineralization is partly overlain by the Kathyln Glacier which is visible from Highway 16. Access to the 3100 m of underground development is from a portal at 1066 m elevation on the east slope of Hudson Bay Mountain."

Jan 1, 1995