Search Documents

By Alex Rown

"THE SYDNEY COAL FIELD has long been afflicted by high costs and low productivities. However, a distinct possibility now exists that improvements can be made in costs, productivities and revenues. If these hopes materialize, the Sydney coal field will once again be regarded as a valuable asset in our national inventory of energy and metallurgical coals. The economic possibilities for the Sydney collieries depend on performance at the pits and in the market place. Because this audience is already well informed about colliery planning, I would like to start with an assessment of the modern coal market insofar as it may relate to the Sydney field. Since 1950 we have seen a vast growth in the population and industrial empires of the western world which has resulted in an enormous and escalating demand for energy. If the energy supply pattern of the first 50 years of this century had been followed, this would have led to an immense demand for coal."

Jan 1, 1972

By P. Simon, G. Falkinger, G. Angerer, B. Gerold

"This contribution presents an investigation of the evolution of shrinkage pores during hot rolling with a special focus on the microscopic mechanism. The reliable closure of pores, which inevitably occur during the casting process, is of crucial technological importance for high-quality hot rolled plate products. Therefore, lab-scale tests were carried out under different typical thermomechanical loadings. Extensive data from optical microscopy was collected before and after deformation. The analysis shows that the average volume of pores evolves similar to the volume of an idealized arrangement of voids in an ideally plastic matrix. The average shape of the shrinkage pores, however, was found to be almost constant during deformation. Even though individual pores exhibit complex morphologies far from any idealized geometries, the overall evolution of a large number of pores is well captured by simple assumptions. In addition to the quantitative analysis, a schematic representation of this counter-intuitive behavior is provided. A simple ‘Gurson’-type void evolution equation was implemented in a three-dimensional Finite-Element model of the industrial hot rolling process. With the help of this mechanism-based process simulation the thermomechanical closure of shrinkage pores during the rolling process has been optimized for a variety of plate products.INTRODUCTION Aluminum alloys of the 7xxx series are widely used in the aircraft industry. They have to meet high quality standards regarding microstructure as well as mechanical properties. For hot-rolled aircraft plates, one of the most important quality requirements is that they are free from pores. Pores, however, are inevitably created during the casting process either due to shrinkage or due to the dissolution of gas from the melt. The pores have to be closed mechanically during the hot-rolling process. Therefore, the mechanism of so-called pore closure or void closure has a high technological relevance for the production of aircraft plates. The behaviour of voids in a ductile matrix subjected to mechanical deformation has been extensively studied, especially in the context of damage mechanics. A recent review (Besson et al., 2010) on modeling methods for ductile damage gives a good impression on how much experimental as well as theoretical effort has been dedicated to the problem of void evolution under mechanical loadings. Although void closure has been studied to a far lesser degree, it obeys to the same general theoretical evolution laws as void growth. The most basic theoretical result is that hydrostatic pressure drives void closure, while hydrostatic tension leads to void growth. The mechanism of void closure depends on the void shape. This is illustrated by the example of a flat penny-shaped void, which under compression obviously closes much faster than a sphere with the same volume. Theoretical models have been developed for the evolution of simplified void geometries, such as spheres or cylinders (e.g. Gurson, 1977), spheroidal (Gologanu et al., 1997) and ellipsoidal voids (Ponte-Castaneda, 1994). In industrial cast ingots, however, the pores exhibit very complex morphologies, which are far from any idealized geometry. X-ray tomography revealed ‘tortuous’ voids in a 5xxx aluminium alloy (Chaijaruwanich et al., 2006)."

Jan 1, 2018

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By Ross D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market.RÉSUMÉRoss D. Lawrence graduated from the University of Toronto with a B.A.Sc. (Applied Geology-1956) and an M.Comm. (Mining Finance-1959). As a student and following graduation, he worked across Canada on a variety of mineral exploration projects.In 1962, he was one of the founders of Watts, Griffis and McOuat, and has practiced as consulting engineer since then. For the past 20 years, Mr. Lawrence has headed up the WGM valuation practice, responsible for a group of professionals which has carried out scores of valuations of mineral properties and mining companies. He is a Certified Minerals Appraiser of the AIMA and an active participant in professional affairs.INTRODUCTIONMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. You will hear from others at this conference about the use of cost and income approaches to the problem of valuing exploration properties. This paper will concentrate on market-based approaches. Market based-approaches are based on the principle of substitution and include such techniques as:??Comparable transaction analysis (sometimes referred to as sales comparison analysis).??Farm-in commitment analysis??Rules of thumbAre there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal committee of the Canadian Institute of Mining, Metallurgy & Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2003

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

By C S. Beals

The Dominion Observatory was founded in 1905 and, from the beginning, it work included research in both astronomical and geophysical science. During its first years, up to 1916, the Observatory also included geodetic surveying as part of it scientific program. Although, at the beginning of the century, geophysics did not have the close connection with mineral exploration that it now holds , the founders of the Observatory were men of vision, and they laid a solid foundation for the application of the techniques of geomagnetism, gravity and seismology to an understanding of the Canadian terrain of plain , mountains, seacoasts and shield area . The particular sphere which the Observatory occupies in the field of geophysics has been evolving over a period of many years and it has now a rather definite relation to the work of other government bodies, university science departments and industrial organizations. We have, for example, an over-all responsibility for the regional magnetic mapping of Canada and, as the magnetic field is subject to slow but steady changes, we produce new magnetic maps of the country every five years. These maps indicate the strength and direction of the magnetic field, the variation of the compass and the rate of change of the magnetic elements.

Jan 1, 1963

By L. H. Cole

Introduction The increasing importance of the gypsum industry in Canada is evidenced by the fact that the production has increased from 473,129 tons valued at $809,632 in 1909 to 1,205,846 tons valued at $3,622,007 in 1928, an increase of over 155 percent in quantity, and of 347 percent in value, in the 20-year period. Although the export trade in crude gypsum still forms a large proportion of the industry, it is gratifying to see that the home consumption is steadily increasing, and while the percentage of the crude gypsum mined that is manufactured into the calcined products in the country is only 16.8 per cent, its value is practically 50 per cent of the total gypsum production of the whole country. It is to be hoped that each succeeding year will see an increase in the amount manufactured in Canada, and, with the steady growth of the country and a serious endeavour to capture a part at least of the world market in gypsum products, the outlook for the industry is decidedly promising. The value of gypsum as a commercial commodity has been known from the time of the early Egyptians; in fact its value for certain purposes has been known so long chat the date of the discovery of its peculiar properties is unrecorded.

Jan 1, 1930

By I. S. Thompson

"The discovery of low-grade copper-silver mineralization near the town of Tipperary, Ireland, by Gortdrum Mines Limited was the result of reconnaissance geological and geochemical exploration followed by target delineation from induced polarization surveys.Initially, orientation studies at the Tynagh lead-zinc orebody showed that such deposits could be readily detected in stream sediments and soils using cold extraction analysis for total heavy metals. Numerous areas showing stratigraphical and structural similarities to Tynagh were then selected for reconnaissance geochemical prospecting.The Gortdrum deposit was detectable through the presence of anomalous metal values in stream sediments 3,000 feet downstream; soil sampling indicated an area of 2,000 by 700 feet containing 2 Yz to 20 times background cold-extractable metal values. Induced polarization surveys defined the dimensions and attitude of mineralization.Drilling to date has outlined (under 10 to 20 feet of till) low-grade copper-silver mineralization within Lower Carboniferous limestones and shales which have been faulted against Devonian sandstone. Mineralization ex-tends from surface to depths of 250 to 450 feet and consists of bornite-chalcocite-tetrahedrite and some chalcopy-rite in altered limestones and intrusive dikes.The deposit is geologically analogons to the Tynagh and Silvermines orebodies, but in contrast exhibits a predom-inant structural control. Provisionally, it is postulated that mid-Carboniferous folding and faulting produced the pre-mineralization high porosity via recrystallization, shearing and brecciation. Subsequently, hydrothermal solutions from the west, with a probable eommon origin to the volcanic dikes, were introduced along the fault planes. Although syngenetic causes cannot be exempted, the field relationships favour an epigenetic origin."

Jan 1, 1967

By H. H. Gardner

Introduction The Greenhill mine of West Canadian Collieries, Limited, is on the Alberta side of the Crowsnest pass, twelve miles from the Alberta British Columbia boundary-line. Here, five coal seams of Lower Cretaceous age are found in the Kootenay formation. They outcrop on the north and south slopes of the valley, with strike approximately N.30°W., paralleling the main range of the Rocky mountains, and dip about 40 deg. westward. Of the five seams, only two, designated No. 1 and No. 2, have been worked to date. On the West Canadian Collieries property, No. 1 seam ranges in thickness from thirty feet to nil. Generally, it has a hard, strong conglomerate roof. No. 2 seam is separated from No. 1 by forty-five feet of shales and sandstones. It has a thickness of eight to thirty feet.

Jan 1, 1947

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By S. Jain

Construction industry is considered as labour intensive, having shortage of skilled labour, unsafe with large number of industrial accidents. Construction industry requires high technology automation products (Robots) for improving productivity, safety, quality etc. Robots are developed by various countries in different areas like demolition, earthwork, bridge, tunnels, road work, underwater works, trenches and piping, maintenance etc. however they are still not used to their full potential by construction industry. Hence in this paper, the authors propose a ?model for adoption? of robots in construction industry. This model considers how a construction firm will adopt full scale robots like manually controlled machine, tele-controlled machines, computer controlled machines and cognitive robots and assimilate them through various stages.

Aug 1, 2013

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By J. Bouchard, A. Clapperton, L. Ebacher, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Froth flotation is used to produce nickel and copper concentrates. As is the case at other operations, the presence of magnesium is detrimental to the flotation products. In the past year, the exploitation of a new deposit has increased magnesium in the feed. Thus, it has been challenging to meet the required ratio in the final nickel concentrate. In search for a consistent solution for this problematic, an empirical flotation simulator making use of selectivity curves was developed. The circuit was expressed as a system of linear equations, which considered the distribution of copper, nickel and gangue minerals in the different streams. The relative quantities of each mineral are given by the separation efficiency curves of the various banks in the circuit. Three sources of data were used to calibrate the simulator: historical plant data (metallurgical balance), infinite dilution bench-scale flotation tests, and direct sampling of flotation cells. The calibrated separation curves were used to predict the recovery of the different species based on a single mineral recovery. Validation of the simulator showed good fit for the valuable minerals. The simulator was then used to infer the optimal operating conditions of the flotation circuit to optimise magnesium oxide content of the nickel concentrate. Simulation of two re-arrangements of the circuit gave a promising solution with a Fe:MgO ratio 2.42 times higher than the minimum value.INTRODUCTION Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Figure 1 shows the location of the mine site. After crushing and grinding, froth flotation is used to produce nickel and copper concentrates. The flotation circuit is designed with multiple stages consisting of bulk copper/nickel flotation, copper/nickel separation, and a separate nickel circuit (bulk float and cleaning)."

Jan 1, 2018

By J. R. D. Gravel, D. A. Poland

"The induration of iron ore pellets has always utilized prefired pellets to protect the pallet cars from the environment of the induration furnace. This paper presents the process used to obtain superior upper sidewalls. These heat resistant castings are used on induration pallet cars, and their life improvements by as much as 400% is a significant step towards the reduction of the prefired (or hearth layer pellets.) The benefit to the industry in the removal of the hearth layer is improved overall productivity. IntroductionThe Iron Ore Company of Canada (IOC) operates with production facilities located in Labrador City, Newfoundland and Sept Iles, Quebec. It has recently been acquired by North Limited, an Australian based resource oriented company. Prior to its acquisition, IOC has examined several methods of operational cost reductions. One of these was an examination of indurrating pallets. Pallets are composed of numerous assemblies and sub-assemblies. The examination of the upper sidewalls began as an intent to increase the operational life of the component. The anticipated net effect was to be a reduction in the overall pallet maintenance cost. All of the components and assemblies have undergone a severe scrutiny. IOC has found that the success of the project has depended upon not only the technical competency of all parties involved, but also upon the ability to share risk, to be innovative, and to find a partner with whom the development can proceed without fear and yet with accountability. IOC has found in Cast Steel Products (CSP) such a partner in the field of pallet development. This paper will undertake to explore the progression into the arena of partnering between IOC and CSP. CSP and IOC met in the fall of 1994. The work of re-engineering the pallets began with an initial order for 36 pallets in March, 1995. The work on the upper sidewalls involved segregation of the effect of alloy development versus physical geometry development. The nature of partnering between the two companies allocated alloy development to IOC and physical geometry development to CSP, yet no advancements were made in either area without the close co-operation or the involvement of both partners."

Jan 1, 1999

By A. Golabchi

Building Information Modeling (BIM) is an increasingly popular method for generating and managing facility information during the life cycle of a building, ranging from facility conceptualization, through design, construction and its operational life. Organizations involved in Facility Management (FM) have the opportunity to use BIM as a knowledge repository to document evolving facility information and to support decisions made by the facility managers during the operational life of a facility. This paper demonstrates the potential of using BIM to develop algorithms that automate decision making for FM applications. The potential of utilizing BIM as an analysis tool is demonstrated through the scenario of HVAC (Heating, Ventilation, and Air Conditioning) system failure in an operating facility. In case of a typical HVAC malfunction today, facility occupants record complaints in a ticketing database maintained by the FM organization. Upon receiving notification of HVAC system failure, facility inspectors visit the location to confirm the reported failure. Upon confirmation, facility managers review building plans and specifications to develop a detailed plan of action to repair any HVAC components suspected of damage. Based on the plan of action, inspectors visit the facility to inspect and, in case of damage, repair the appropriate HVAC system components. These FM practices ? as currently implemented across the industry ? are labor intensive, time consuming, and often rely on unreliable and outdated information. To address these shortcomings, the authors propose an alternative methodology of HVAC fault detection in operational buildings. The authors implement an algorithm that leverages complaint ticket data and automates BIM to determine potentially damaged HVAC system components. Based on the list of HVAC components suspected of damage, the algorithm develops a plan of action for the facility inspectors. Finally, the authors discuss the advantages of the proposed method as well as the challenges of implementing automated BIM-enabled decision making processes in the FM industry.

Aug 1, 2013

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By P. Nelson, B. Salt, J. A. Scott, H. Shang

ABSTRACT In a nickel smelting process, large amounts of off-gas emissions are generated, which can cause serious environmental and plant hygiene problems if not properly treated. With increasingly stringent environmental regulations, an enhanced understanding of well-controlled, off-gas cleaning systems is vital. In this paper, dynamic models for an industrial smelter, off-gas system tackling hazardous sulphur dioxide, carbon monoxide, and carbon dioxide are developed using mass continuity, momentum, and energy conservation laws. The effect of air in-leakage is explored under different operating conditions. The developed models provide an enhanced process understanding and a necessary basis for highperformance control analysis of smelter off-gas systems.

Jan 1, 2011

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By T. Feldmann, G. P. Demopoulos

The feasibility of chloride leaching processes depends on interfacing them with cost-effective HCl regeneration technologies. This paper summarizes the most important findings of research conducted in the past 3 years concerned with a novel process to regenerate high-strength HCl from concentrated CaCl2 solutions at temperatures below 100°C, via reaction of CaCl2 with H2SO4 resulting in the formation of calcium sulfate phases (gypsum, a-hemihydrate or anhydrite). From constant supersaturation semi-batch experiments in pure solution it was found that the crystal growth rate of hemihydrate, and hence the particle size, was influenced by the rate of reagent (Ca2+, SO4 2-) supply to the reactor. Additionally, growth studies of DH in presence of impurities (K+, Mg2+, Sr2+, Ba2+, Fe2+/3+, Al3+, La3+, Y3+, F- and PO4 3-) showed that specifically Sr2+ and PO4 3- are taken up during crystal growth. Furthermore, it was found that decreasing water activity (via different HCl/CaCl2 concentrations) and increasing temperature reduce the metastable life-time of DH and HH by increasing the phase transformation speed. The DH/HH transformation was identified to be dissolution-precipitation based, while HH to AH is a topochemical process. Finally, continuous experiments on bench scale are underway to confirm the feasibility of the process to obtain super-azeotropic strength HCl with up to 9 mol/L (~30wt.%) from 5 mol/L CaCl2 (~40wt.%) solution.

Jan 1, 2014