Search Documents

By M. H. Cullender

THE determination of the flow characteristics of gas wells depends upon the analysis of pressure data obtained under shut-in conditions and under one or more known flow conditions. These data are commonly referred to as back-pres-sure test data, and I know you are all familiar with the back-pressure equation where, Q rate of flow, Mcfd @ standard conditions C coefficient of the back-pres-sure curve P 1 formation pressure, psia P • sand face flowing pressure, psia P2 (psia)2/1000 n exponent of the back-pres-sure curve Figure 1 is a graphical presentation of the back-pressure equation; the coefficient is the rate of flow at a difference in squared pressures of 1, in this case 2250 Mcfd, and the exponent defines the manner in which the rate of flow changes with a change in the difference in squared pressures. In Figure 1, the exponent of the back-pressure curve is 0.554 which means that for a 10-fold change in the difference in squared pressures, there will be a 3.58-fold (10 raised to the 0.554 power) change in the rate of flow.

Jan 1, 1961

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By Technische Universität Braunschweig, K. Saksl, J. Furste, P. Eschenbacher, F. Brunke, D. Wolter, M. Kohnke, C. Siemers, J. Kiese, M. Schlemminger

"In general, titanium alloys combine outstanding mechanical properties with corrosion resistance and biocompatibility and are, therefore, used in many challenging applications. Nevertheless, for special products, well-tailored properties are required which might not be achievable by a specific design so that new or modified alloys are needed. In this overview paper, alloy development strategies performed at the Institute for Materials of the Technische Universitat Braunschweig are discussed at different examples, namely, (1) oxidation-resistant, microstructural-stabilized and cold-workable alloys for exhaust applications, (2) aluminum- and vanadium-free, medium-strength and cold-workable alloys for implants and osteosynthesis applications and (3) free-machining alloys by the addition of particles with low melting points for non-safety critical light-weight constructions to replace heavier steels, e.g. in automotive applications. A special focus is set on the alloy development techniques and the analyses carried out to achieve well-balanced properties by the optimization of the alloy compositions. INTRODUCTIONTitanium belongs to the allotropic metals and can therefore exist in two different equilibrium lattice modifications. Pure titanium crystallizes at 1668°C in a body centered cubic (bcc) structure called ?- titanium which at 882°C transforms to a hexagonal close packed structure (hcp), the a-titanium. A martensitic ?-to-a-transformation is possible at large cooling rates. This thermally induced hexagonal martensite is called the a'-phase. The transformation temperature named ?-transus-temperature (T ?) can be influenced by alloying elements (Peters & Leyens, 2002).For titanium alloy production typical alloying elements are aluminum (Al) and oxygen (O), both a-stabilizers shifting the ?-transus temperature to higher temperatures, whereas tin (Sn) and zirconium (Zr) only show a limited influence on the ?-transus temperature. The ?-stabilizing elements are subdivided into two groups: Niobium (Nb), molybdenum (Mo) and vanadium (V) stabilize the ?-phase between the melting point and room temperature and are therefore called isomorphous -stabilizers. Elements like copper (Cu), iron (Fe) or silicon (Si) also stabilize the ?-phase to lower temperatures but undergo a eutectoid reaction during cooling. ?-titanium then dissociates to a-titanium and an intermetallic compound. Consequently, these elements are called eutectoid ?-stabilizers (Boyer, Welsh & Collings, 1994)."

Jan 1, 2016

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, Amabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes from these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, A mabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes f rom these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By G. M. Ritcey, K. E. Haque

"Laboratory-scale sulphuric acid leach tests were conducted on Elliot Lake and Rabbit Lake ores in the presence of various oxidants, namely: Fe2(SO4)3, CI2, H2O2, NaClO3, MnO2, H2SO5, HNO3, Oxon e, K2Cr2O7, KMnO4, O3 and O2. Uranium extraction is significantly accelerated when an oxidant is present in the leach slurry. Uranium extraction of 96-99% can be achieved by maintaining the oxidation potential of the leach slurry in the range of400 to 500 m V (S.H.E.). A rough cost comparison of all the oxidant s indicates that the use of Fe2(SO4)3, 02, O3, C12, HNO3 or MnO2 is far less expensive than NaClO3 and the uranium extraction rates are similar to or better than with NaCIO3. For uranium extraction, it is concluded that gaseous oxygen (i.e., air or oxygen) would be the most effective and economical oxidant for the 24- to 36-hour leach of Elliot Lake ore; whereas for the 8- to I2-hour leach of Rabbit Lake ore, a strong chemical oxidant (e.g. NaCIO3, H202, 03, K2Cr2O7, H2SO5 or HNO3) would be a logical choice.IntroductionThe common practice for the treatment of uranium o res is leaching with sulphuric acid or with a carbonate-bicarbonate mixture. Generally, the latter process is ad opted when an excess (> 18%) of acid-consuming components (e.g., carbonate) is present in the ore. Irrespective of the nature of the leachant, the addition of an oxidant to the leach mixture is necessary to obtain a high uranium extraction.The maximum extraction of uranium can only take place when all the uranium is in the highest oxidation state (i.e.,U +6-uranic ion) . Because a certain percentage of uranium present in the ore is invariably in the lower oxidation state (i.e.,U+4-uranous ion) , the addition of an oxidant to the leach slurry is necessary to oxidize uranous ion to the uranic state."

Jan 1, 1982

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

By Lin Li, Ahmad Ghahremaninezhad

"In this paper, the electrochemical behavior of ferric and ferrous couple on the pyrite surface was studied by application of the chronoamperometry technique in an acidic solution at room temperatures and atmospheric pressure. The effects of the pyrite origin, ferric and ferrous ions concentration on the electron transfer kinetics of Fe3+/Fe2+ reaction were probed. Tafel behavior of all the test conditions were developed. The results showed that the ferric-ferrous reaction on pyrite electrodes with different origins have a common mechanism, despite different reaction kinetics. The exchange current densities of the redox reaction have the same magnitude of about 10-5 A·cm-2, which is far lower than the value reported for the gold and platinum electrodes, but larger than that of the chalcopyrite electrode. The cathodic transfer coefficients are between 0.4 and 0.5, while the anodic transfer coefficients appear unusual with the lowest value being 0.23. It was also demonstrated that an increase of one order of magnitude of iron concentration has no clear effect on the exchange current density and cathodic transfer coefficients of Fe3+/Fe2+ redox reaction.INTRODUCTIONPyrite, FeS2, is mostly considered as a gangue mineral which frequently coexists with valuable minerals and metals, such as gold, copper and nickel. Its separation from valuable minerals can be a costly process (Chandra & Gerson, 2010). In refractory gold ores, the fine gold particles are locked inside the pyrite structure. Oxidative leaching of pyrite is a hydrometallurgical method to destroy the structure of pyrite and expose the fine gold particles to the cyanide solution in the downstream cyanidation circuit. Pyrite oxidative leaching can be achieved by oxidation of pyrite via oxygen and ferric ion(McKibben & Barnes, 1986). In fact, pyrite oxidation by oxygen and ferric is a significant source of acid mine drainage(AMD), which adversely causes serious environmental problems(V. P. Evangelou, 1995).The pyrite oxidation mechanism is accomplished in three consecutive steps: (i) pyrite is oxidized by oxygen and ferrous ion formation (Eq. 1); (ii) ferrous oxidation by oxygen and ferric ion formation (Eq. 2); (iii) pyrite oxidation by means of ferric ions (Eq. 3). Hence, both oxygen and ferric participate in the pyrite oxidation process (Moses & Herman, 1991):"

Jan 1, 2016

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs' Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By A. Miura, R. Winarko, D. B. Dreisinger

Chalcopyrite leaching in acidic ferric sulfate media at ambient temperature exhibits slow kinetics and poor leaching efficiency, which is typically attributed to surface passivation. Recently, the presence of small amounts of iodide in the leaching media has been reported to significantly accelerate chalcopyrite dissolution. To further explore the behavior of chalcopyrite leaching in the presence of iodide, it is essential to determine the factors that control the leaching kinetics. In this study, we investigated the effect of initial solution potential, iodide concentration, particle size, and temperature on the kinetics of copper extraction from chalcopyrite. The key in the experimental setup was to minimize iodide loss by iodine evaporation and precipitation as cuprous iodide. The former was achieved by performing the leaching tests in fully sealed leaching systems. The latter was achieved by maintaining the solution potential higher than 420 mV (versus Ag/AgCl electrode), where formation of CuI precipitate is possible. The experimental results show that higher solution potential and higher iodide concentration had a pronounced positive effect on the rate of chalcopyrite dissolution. There was no effect associated with particle size, which might be due to the narrow size range tested. The positive effect of increasing temperature only manifested itself when the solution potential was sufficiently high. INTRODUCTION The main challenge of chalcopyrite leaching using ferric ions as the oxidant at ambient temperature is the slow kinetics and poor extraction. The reason for this leaching behavior has been attributed to passivation resulting from formation of insoluble passivating layers on chalcopyrite surfaces, which could be metal-deficient sulfides, elemental sulfur, polysulfides, and iron precipitates (Klauber, 2008). To overcome passivation, technologies using higher temperature and pressure have been developed to leach chalcopyrite concentrates, such as the CESL process (Mayhew, McCoy, Mean, & Woeller, 2013), FLSmidth Rapid Oxidative Leach (ROL) process (Mulligan et al., 2017), Galvanox (Dixon, Mayne, & Baxter, 2008), Albion process (Hourn, Turner, & Hourn, 2012), HydroCopper (Hyvärinen & Hämäläinen, 2005), TPOX (Dreisinger, 2006), and AAC/UBC process (Dreisinger, Dempsey, Steyl, Sole, & Gnoinski, 2003). Even though they are effective in accelerating copper leaching kinetics, those technologies typically have higher capital and operating costs associated with production of concentrates and application of autoclaves. This makes them unsuitable for treating low grade primary copper sulfide ores.

Jan 1, 2019

By David Christensen

The long-term performance of dry covers is being examined in a research study funded by the International Network for Acid Prevention (INAP). The study was separated into two phases. The two main components of Phase 1 of the study were the identification and research of the processes affecting the long-term performance of dry cover systems and an examination of available numerical models for simulation of long-term cover performance. Identification and research of the physical, chemical, and biological processes affecting long-term performance showed that cover performance could be related to the change in the saturated hydraulic conductivity of cover material, the change in the soil-water characteristic curve, and the physical integrity of the cover system. Seven numerical models were examined to evaluate their effectiveness in predicting the long-term performance of cover systems. VADOSE/W (Online Help v1.01, 2002) was selected for use in cover system modeling in Phase 2 of the project. Phase 2 of the research study is currently in progress and involved the selection of five mine sites with a minimum of three years of performance monitoring data for analysis of cover performance. Two of the mine sites will be analyzed with the two-dimensional VADOSE/W numerical model. In addition, field saturated hydraulic conductivity tests were completed at three mine sites to investigate the change in field hydraulic conductivity of the cover system materials. The objective of the field testing program was to evaluate changes in hydraulic conductivity of cover material with time. Measurements of field hydraulic conductivity were completed with a Guelph permeameter and a pressure infiltrometer at three sites. The field hydraulic conductivity data was used to evaluate whether a change in this key material property had occurred over time. Field observations and the historic performance monitoring data provided the necessary information to develop hypotheses as to the likely processes that led to any change in field hydraulic conductivity. This paper will briefly summarize the research completed in Phase 1. The remainder of the paper will focus on the field testing program completed to measure the field hydraulic conductivity of constructed cover systems.

Nov 1, 2002

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017

By Arthur A. Cole

Although the metal silver has been known and prized from very ancient times, it is in the New World that the greatest silver camps have been found. This is shown in the following comparison: [] For the last few years, the World&apos;s annual production of silver has averaged about 240 million ounces troy. Of this total, the North American Continent contributes approximately three quarters, Mexico leading with 38 per cent, followed by the United States with 27 per cent, and Canada with nearly 9 per cent.[] Of the largest silver producers in Canada, the Sullivan takes first place. Although primarily famous as a lead and zinc mine, it produced, in 1926, more than 4.5 million ounces of silver. The Premier mine, in northern British Columbia, produced more than 3 million ounces. In Ontario, the largest producers in 1926 were the Nipissing mine, .with 1.9 million ounces, and the Keeley mine, with 1. 7 million ounces. The Mining Corporation produced 1.1 million ounces from mines in the Cobalt district proper, and an equal amount in South Lorrain; while from the Castle-Trethewey mine, in Gowganda, there was an output of slightly less than one million ounces.

Jan 1, 1927

By R. B. Nourse, R. Hundermark, B. Masters, H. Joubert

The new 30 MVA slag cleaning furnace at Waterval Smelter, Rustenburg Platinum, South Africa, has been in operation since 10 March 2003. The furnace design and operation face a number of challenges including a wide variety of feed materials and resulting bath conditions. Furnace feed varies in combinations of granulated Waterval Ausmelt Converter Slag (WACS), hot fed Peirce-Smith converter slag, concentrate and reverts. Coke is added as reductant. The resulting slag composition varies considerably and regularly. For the case feeding WACS an almost pure fayalitic slag (60%+ FeO, 30%+ SiO2) with a very low viscosity results. Due to the widely varying slag conditions, including a superheated fayalitic slag with high fluidity, a robust sidewall design is required adjacent to the slag bath. For this reason the furnace sidewall is equipped with Pyromet&apos;s MAXICOOL® high intensity copper cooling system. The design and installation of the copper coolers as well as tap holes are discussed. To cope with the variation in bath conditions and high slag superheat (350°C when tapped at 1650°C), the copper coolers are capable of removing peak sidewall heat fluxes above 500 kW/m2. Feedback is included on the performance of the Pyromet MAXICOO® copper cooling system for the first two years of operation. The paper further includes an overview on the design and performance of the tap holes, furnace shell, furnace roof and copper slag spouts.

Jan 1, 2005

By R. A. King, B. G. Hunt, C. E. T. White

"This paper reviews the history, occurrence, properties, and uses of indium, and describes the commercial production and fabrication of that metal by The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), at Trail, B.C'. Indium is produced commercially at Trail from dross retreatment furnace D.R.F.) slag, a complex by-product of the lead smelting operations. Furnace feed prepared from this slag is smelted with coke and limerock in an electric furnace. The e1ectric furnace bullion is parted electrolytically, producing a market-able lead-tin alloy containing about 8 per cent tin, and leaving the indium in the anode slime. Recovery of indium from the anode slime involves roasting the slime with sulphuric acid, followed by leaching with water, purifying the leach solution, recovering the indium by sponging with zinc or aluminum, and re-fining electrolytically. This process yields standard grade (99.97+ per cent) indium which is either sold or refined •to high purity ( 99.999 per cent) indium for special uses requiring higher purity metal."

Jan 1, 1959

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977

By R. Esteban, D. Runnels, J. Torrealba-Vargas, G. Couture

"Data handling is an important step in the development of a simulator of a mineral processing circuit. The model requires representative data of the scenario to be modeled. The model development involves protocols that must be followed very closely to complete a successful project.Data handling of large and diverse datasets (metallurgical test results, geological data, mining models, historical data, etc.) is a key element of the model. The information needs to be processed, reconciled, interpreted, modeled and presented to support the design or the optimization of a mineral processing plant.Best practice recommends that teams from different disciplines (such as mining, metallurgy, geology and environmental) interact to define the most important variables that could influence the simulator. For example by adopting a geometallurgical approach in the earlier stages of the project, it is possible to consolidate the number of main ore rock types in a testwork program (saving money and time) by involving geologists and metallurgists in the sample selection and data interpretation.Planning the development of a model involves an understanding of the software capabilities but also the limitations and the magnitude of the data required to calibrate the model in case of changes in the project.A successful model requires a deep understanding of the circuit to be modeled and thus plant personnel should be considered as members of the team.This paper describes the use of the "state of the art" tools for data analysis, simulation and optimization; and shows three practical examples of the use those tools in the design of mineral processing plants."

Jan 1, 2015

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015