Search Documents

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By W. Hawker, A. M. Ivana

"Pressure oxidation is used to liberate gold from refractory sulphide ore and concentrates with over fifteen autoclaves in operation. Despite the importance of pressure oxidation, the autoclave chemistry and chemical thermodynamics are not well established. For example, there is no consensus on aqueous iron speciation or stability of jarosite phases. Additionally, there remains questions about basic ferric sulphate formation and stability. In addition to a review of the current state of knowledge, a methodology to study the ferric precipitation reaction and relate the results to chemical thermodynamic predictions is presented which will be used to accurately define the phase boundaries of the iron precipitates in the future (hematite, jarosite and basic ferric sulphate).INTRODUCTION With declining availability of orebodies that respond to simple leaching conditions, pressure oxidation has become a prevalent technology to liberate gold locked in sulphide mineral matrices. Gold pressure oxidation was established 32 years ago, with McLaughlin being the first facility in 1985 (Thomas & Pearson, 2016). Pressure oxidation is carried out at elevated temperatures ranging from 180 to 240°C as shown in the summary of operations in Table 1 (Ruonala et al., 2016; Fleming, 2010).A considerable amount of research has been done to study iron solubility and precipitation under autoclave conditions (Tozawa & Sasaki, 1986; Umetsu et al., 1977; Sasaki et al., 1993; Fleuriault, 2016; Cheng & Demopoulos, 2004; Papangelakis et al., 1994; Yue et al., 2003). These reports provide a description of the process chemistry and iron behaviour in the autoclave. However, there remain questions about the type and stability of aqueous species and solid phases. This detailed information is required to build a robust chemical thermodynamic model of the system, allowing for equilibrium and kinetic reaction limitations to be discerned."

Jan 1, 2017

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

By T. R. Eger

Miners can be exposed to whole-body vibration (WBV), when sitting or standing to operate mobile equipment. In order to prevent vibration-induced injury it is important to understand how miners can be exposed to vibration, the health risks associated with vibration exposure, methods to evaluate vibration exposure, and strategies to reduce vibration exposure. WBV exposure typically occurs when operating mobile equipment, such as a load-haul-dump vehicle, haulage truck, or dozer. The probability of health effects such as low back pain, neck pain, headaches, and gastrointestinal track problems occurring from daily vibration exposure can be determined based on criterion values published in ISO 2631-1 and EU Directive 2002/44/EC. A special case of WBV termed foot-transmitted vibration (FTV) occurs when a miner is exposed to vibration that travels through the feet. FTV typically occurs when standing on vibrating surfaces associated with the operation of locomotives, jumbo drills, bolters, or raise platforms; however, there is no set standard to evaluate health effects associated with FTV. Recent medical evidence confirms workers exposed to FTV can develop cold induced blanching of the toes, in addition to numbness and tingling in the feet and toes. In order to reduce the risk of adverse health effects from exposure to vibration, the hierarchy of controls (elimination; substitution; engineering; administration; and personal protective equipment) should be followed. Best practices should be used to minimize vibration exposure through equipment purchases (i.e. vehicles with lower vibration emissions and seats that attenuate vibration), reduced driving speeds, and improved road maintenance for example. The elimination of other risk factors, which increase injury risk when combined with WBV exposure, such as awkward working postures, should also be eliminated. Very little is known about FTV exposure therefore further research is required in order to develop exposure standards and identify prevention strategies.

Aug 1, 2013

By K. Östcrdahl

We are developing a cost-saving and environmentally friendly process with low energy consumption to recover the metal content and recycle the acid from spent pickle baths. The metals are precipitated as metal fluorides, which can be turned into metal oxides and hydrofluoric acid by thermal hydrolysis. In the proposed process the solution is concentrated by nanofiltration and the metals are precipitated in a subsequent crystallization step. Different nanofiltration membranes have been evaluated in experimental batch tests. The membrane MPF-34 from Koch Membrane Systems offered both good flux and acceptable metal retention even after long periods of acid storage. The solubility of B-FeF3.3H20 has been measured at varying acid concentrations and at different temperatures. The solubility decreases with increasing hydrofluoric acid and nitric acid concentrations. This suggests that the crystallization process should be operated at high acid concentrations. The crystal growth rate of B-FeF3.3H2O is found to be quite low but increases significantly with temperature. This suggests that the crystallization process should be operated at higher temperatures (40 - 60°C). Within the project a pilot plant has been constructed where the spent pickle bath solution is concentrated by nanofiltration to the desired metal fluoride supersaturation, and B-FeF3.3H2O is crystallized in a 10 L continuous crystallizer.

Jan 1, 2006

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By D. Shen, J. Cheung

Variable reactance arc control by the SPLC (Smart Predictive Line Controller) has been installed at many different mining sites and steel processing plants around the world. Since its first installation 18 years ago, many advances have been made to both the technology, and to its integration with furnace processes and plant operations. The SPLC has helped to improve electric arc furnace stability by reducing electrode movement while maintaining flat line arc power. Stable furnace operation at higher average power increases productivity. This paper summarizes the progression of electro-technology at Hatch since the 1970s, including fixed and variable reactance, digital electrode regulation, and fast variable speed hydraulics for Soderberg electrode, as demonstrated and benchmarked through projects and lessons learned over the years.

Jan 1, 2015

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

By Pura Alfonso, Teresa Escobet, Hernan Anticoi, Eduard Guasch, Josep Oliva, Sarbast A. Hamid

"The liberation modelling of mineral particles using mineral liberation analysis have been used in the past to model comminution and concentration processes. In this work this concept has been taken a little further, using comminution and concentration for applying the mineralogical characteristics of particles. This approach is shown using the image analysis, mineral liberation analysis and the distribution density functions for liberation modelling. The work focused on the effect of comminution on mineral liberation for liberation modelling. To model this, effect the mineral liberation of the particles using distribution density and the cumulative distribution was linked to the image analysis of the ore particles. These properties have been estimated by statistical measures such as the distribution density and liberation grade, which were extracted from MLA data and images analysis, using proper image analysis and techniques based on MATLAB software. A comparison of different tungsten ores of liberated particles, has been introduced and evaluated by estimated results and image analysis.INTRODUCTION The chief economic minerals of tungsten are wolframite [(Fe,Mn) WO4] and scheelite(CaWO4), and approximately two-thirds of the world tungsten reserves consist of scheelite deposits (Lassner and Schubert, 1999). Tungsten has unique properties and is widely used in various industrial high strength and high temperature applications. It occurs coarsely aggregated in low grade ores. Most of tungsten ores, particularly scheelite, wolframite and ferberite, occur in deposits with very low content of WO3 (0.1–2.5%) that is not economically viable to apply directly metallurgical methods to extract tungsten (Martins, 2014). Tungsten is considered as a critical metal by the European Union by the economic importance and also the high supply risk (European Commission, 2014; Chakhmouradian et al., 2015).Currently, scheelite is playing an increasingly important role in tungsten industry because the mineral reserve of wolframite is getting depleted after gradual exploitation and utilization (Min et al., 2016). In mineral processing, the liberation of valuable mineral from the gangue determines the efficiency of subsequent separation processes. The liberation characteristics of an ore are primarily dependent on its texture, the association of mineral in the host matrix of gangue minerals, and to some extent on the grinding process (Zhang and Subasinghe; 2013)."

Jan 1, 2017

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017