Search Documents

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By Normand Champigny

The Forces of Change ? The current business environment ? What can we expect for the future on management of physical assets ? The impact of maintenance on production costs ? What is RCM is doing is improving business performance ? The beginnings of RCM The RCM II Process ? RCM II is a structured process that involves employees in determining the best failure management tactics for systems and equipment in their operating context ? The method is an effective approach to risk and cost reduction as well as failure management

May 1, 2002

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By J. E. Armstrong

THE Pinchi Lake mercury belt is in central British Columbia, about fifty miles north of the Prince Rupert branch of the Canadian National railway (Figure 1). Until 1936 little was known about the geology of this area. Jn 19~6 and 1937, J. G. Gray and the writer mapped the Fort Fraser area (G.S.C. maps 630A and 631A) for the Geological Survey of Canada. During the field season of 1937, cinnabar was discovered by J. G. Gray in the Permian limestones on the north shore of Pinchi lake on what have since proved to be the main showings of the Pinchi Lake mercury mine. Claims were staked in the spring of 1938 and later that year were optioned to the Consolidated Mining and Smelting Company. Development work revealed cinnabar deposits of commercial size and grade, and a small reduction plant was erected, production of mercury commencing in June, 1940. Since 1940, this plant has been enlarged by additional units. The ore treated is reported to contain between 0.5 and 0.75 per cent mercury. The production of mercury from this deposit is now far in excess of Canadian requirements and this country is able to supply the United Kingdom with part of its needs. In 1940 and 1941, several other occurrences of cinnabar were found northwest of Pinchi lake. During 1941, the writer made a geological investigation of the known cinnabar occurrences and of the belt of country in which they are located. The present paper summarizes the results of this work. The writer is indebted to officials of the Consolidated Mining and Smelting Company, and to Mr. E. Bronlund of the Pinchi Lake mine in particular, for their generous co-operation in the work.

Jan 1, 1942

By I. Demers

The abandoned Manitou mine site covers an area of approximately 190 ha near Val d?Or, Quebec. This old site has been generating acid mine drainage for several decades. In 2006, a partnership was established between the Quebec Ministry of Ressources Naturelles (MRN) and Agnico-Eagle Mines to reclaim the Manitou site using tailings from the nearby Goldex mine. These neutral tailings were to be deposited on top of the Manitou site. An extensive study was performed to evaluate specific reclamation scenarios to control acid mine drainage using Goldex tailings as cover material. The article first describes the global approach used for this evaluation, which includes in-situ hydrogeological monitoring, tailings characterization, laboratory column tests, and numerical modelling. Of the thirteen column tests, three were conducted to evaluate the parameters affecting the performance of covers made of Goldex tailings placed over the spillage area of the Manitou site. Geochemical and hydrogeological parameters were assessed during the leaching column tests for almost two years. The tests aimed at evaluating the effect of water table level and monolayer cover thickness on the overall performance. The testing procedure involved monthly leaching and measurement of geochemical parameters. Results indicate that water table position is the most important factor affecting the monolayer cover performance to control AMD. Based on these results, it was established that the water table must be located near the interface between the Goldex and Manitou tailings to effectively reduce AMD generation. Cover thickness also has an impact on cover performance, which is however less significant than the water table position. The testing scenario with a water table located at the interface with a one-meter Goldex tailings cover showed progressive improvement in effluent quality.

Aug 1, 2013

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By S. Orangi

A representative sample of ramming paste from a peripheral seam in an aluminium electrolysis cell was taken in order to develop a process to fabricate ramming paste samples in the laboratory. To this end, paste material was compacted in multilayers in a mould designed to be representative of peripheral seams in Alcoa's smelters. The density distribution in the representative sample was measured ranging from 1.51-1.76 g/cm3. The density range obtained by the proposed methodology in laboratory is 1.47-1.77 g/cm3. The results demonstrate that the proposed fabrication method adequately duplicates paste density from the cell for both one and two layer compaction. Finally, preliminary results related to the compressive strength and Young's modulus of laboratory samples were obtained at various temperatures and are presented in this paper.

Jan 1, 2011

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By Du Xinfeng

The resource quantity of the low rank coalbed methane (CBM) accounts for 47% of the total resource quantity of CBM in China. Compared with the exploration and development of the high rank CBM in Qinshui Basin, China and the low rank CBM in Powder River Basin, USA and Albert Basin, Canada, the exploration and development of the low rank CBM are still in the initial test stage. In this paper, on the basis of analyzing the mining geological conditions such as that the Huanglong Jurassic Coalfield is largely situated in the hills and gullies zones, and the coal reservoir has the features such as the low metamorphic degree, large coal seam thickness, simple coal matrix texture, high permeability and small CBM content and so on, it discusses the key technologies such as the development pattern of CBM, well location arrangement, drilling and well completion technology and fracturing technology and so on. It indicates that the underbalanced drilling and the cavity well completion based on the reservoir protection will be the development directions of the CBM development technology in this area.

Aug 1, 2013

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By J. G. Pearson, F. H. MacDougall, A. G. Galley

The difference in age, host rock lithology, alteration and style of mineralization indicates a fundamental difference in the format ion of gold deposits in the Flin Flon and Amisk Lake areas. The Flin Flon area contains early quartz-sulfide-gold veins fo rmed within intermittently active fractures and later plutonic hosted deposits thought to be generated in a porphyry system. In the Amisk Lake area two types of gold occurrences are recognized: I) gold-quartzcarbonate- sulfide veins within or flanking fault zones and 2) structurally and stratigraphical ly controlled zones of dissem inated and vein type sulfide-gold mineralization within extrusive and intrusive rhyolite and dacite porphyries. Both types of deposits are set within supracrustal rocks. are accompanied by intense alteration haloes and were formed prior to the major deformation event suggesting an early, epigenetic hydrothermal origin.

Jan 1, 1986

By John H. Fowler

Nova Scotia has been mining and exporting industrial minerals for over two hundred years. As an industrial mineral producer, this province continues to rank as the number one gypsum mining and exporting region in North America. Mining of many other commodities is ongoing, supplying many local and export markets. In all, excluding aggregate producers, there are nineteen industrial mineral producers operating at thirty sites producing nine commodities including anhydrite, barite, clay and shale, dolomite, gypsum, limestone, salt, silica sand and stone (Fig. I). Numerous aggregate producing operations supply all the province's aggregate requirements and export some of these materials to other regions of Atlantic Canada and as far away as Bermuda (Fig. 2) . Production value of industrial mineral commodities in Nova Scotia for 1982 was $105 million , representing 39% of the total value for all mineral production for the year. Because of the general improvement in the economy, indications are that the 1983 value of production will be higher.

Jan 1, 1984

By O. G. Olvera, D. G. Dixon, E. Asselin, L. S. Quiroz

Dissolution rates of chalcopyrite (CuFeS2) were calculated using electrochemical impedance spectroscopy (EIS). The calculated dissolution rate decreased by a factor of 3.2 after the electrode was passivated. The results presented in this work indicate that the reduction of Fe3+ was the rate-controlling step for fresh CuFeS2 electrodes while the transport of cations within the passive film limited the dissolution rate for the passivated electrode. The transfer of cations at the electrode/electrolyte and passive film/electrolyte interfaces did not affect the dissolution rates of the fresh and passivated CuFeS2 electrodes, respectively. The catalytic effect of pyrite (FeS2) on the dissolution of CuFeS2 continued after the passivating treatment. The contact of fresh and passivated CuFeS2 electrodes with different FeS2 particles resulted in increased dissolution rates, due to an increase in the reduction rate of Fe3+.

Jan 1, 2014

By Alfred C. Lane

WE recently received from Professor A. C. Lane, Emeritus Professor of Geology and Mineralogy, Tufts College, Mass., and a Corresponding Member of this Institute, a very interesting account of some recent developments in radioactive methods of determining the age of minerals and, therefore, of the rocks in which they occur. It deals in particular with studies of the minerals of certain pegmatite dykes on the Huron claims and Bear claims in southeastern Manitoba, which, the results indicate, are among the oldest rocks of the earth's crust. The following article presents a non-mathematical summary of Professor Lane's paper . . It will be noted that he is anxious to obtain suitable samples of certain minerals and rocks for further age studies. We hope some o our members may be able to supply him with the material he needs. It may be well to explain briefly how the age determinations are made. Uranium is continually breaking down, or disintegrating in successive steps through radium, etc., to a final product which is lead (uranium-lead), and the rate at which this change takes place is known. Minerals containing uranium will therefore contain lead also, and the lead-uranium ratio mul-tiplied by a certain factor (approximately 7 ,600) will give the age of the mineral in millions of years. Thorium also disintegrates at a known rate to give lead (thorium-lead) as a final product, and the age of a mineral containing thorium can thus be calculated from the lead-thorium ratio. Thorium breaks down more slowly than uranium. In unit time, one gram of thorium produces about as much lead as 0.36 grams of uranium.-ED.

Jan 1, 1938

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006