Search Documents

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

By H. A. Steane

THIS BRIEF PAPER presents the information available on the use of Dorrclon?is in the middling re-grind unit at the lead-zinc mill of Canadian Exploration Limited. The plant throughput is 1,650 tons per twenty-four hours. The flotation feed is ground to 60 per ?Cent passing through 200 mesh. It contains some composite 11articles of sphalerite in calcite, and these reported either in the final zinc concentrate, thus lowering the grade, or in the tailing, with loss of zinc. The re-grind unit was set up in the zinc flotation circuit to liberate the sphalerite from these middling particles, to raise the grade of concentrate and improve recovery. Grinding through 325 mesh should give substantial liberation of locked sphalerite. The middling regrind unit consists of two Dorrdones and one ballmill arranged as shown in the -accompanying flow-sheet. The Hardinge ball-mill, size 7 ft. x 36 in., was free for this use as a result of recent plant expansion. The two Dorrclones were purchased, and the necessary pumps and pipe lines were installed to complete the regrind unit. The unit has been developed over a period of two years by several steps and various flow schemes until reaching tl1e present flow scheme. These steps are not elaborated here, because the changes were made to determine the best product to work on for flotation metallurgy, and not because of the Domrolone classifying ability.

Jan 1, 1956

M INE production requires the coordination of the talents of men and the use of equipment. Mine operators maintain a continual surveillance of equipment, looking for improvements and modifications that will benefit them. Few give similar attention to the advances made in the education of mining engineers since they themselves graduated. That is not surprising. Education lacks the advertising budget available to manufacturers. A modification to improve a mechanical contrivance is advertised, and an advertiser's press releases get attention by publishers. The whole program for mining engineering education could be revolutionized and no one, except a few professors, would know about it. The Canadian Institute of Mining and Metallurgy's newly established General Commit-tee on Education can improve that situation. Nine groups of engineers in Canadian universities are trying to give undergraduates an education that will make them useful to the mineral industry as mining engineers. The tabulation offered here (Table I) is an analysis of the distribution of the undergraduate-teacher contact time.

Jan 1, 1963

By H. L. Cameron

Introduction Since the beginning of gold mining in Nova Scotia in the year 1860, the biggest problem o the mine operators has been to find and follow the ore zones in the narrow quartz veins. It was early recognized that all veins were not gold bearing and that, in those that were, the commercial ore was confined to limited zones. A large number of geologists and mining engineers have been interested enough to give time and thought to the problem, but, until the last four or five years preceding World War II, they were handicapped by lack of exact data from mining operations. The necessary data could only be obtained by daily checking of underground operations. Such daily checks were instituted at a number of mines during the period 1935-40 and, in every case, were successful in delimiting the ore zone or zones for the particular mine. The present paper deals with the results of this work as applied to practical ore finding. It is an attempt at extrapolation, from observations in the four districts with which the writer is personally familiar, co other districts in which similar conditions or structures are reported.

Jan 1, 1947

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015

By E. Krause

The oxidation of Fe(II) with S(IV) and oxygen can be used advantageously in leaching systems requiring both Fe(III) and sulfuric acid; e.g., heap leaching of sulfide-containing ores or concentrates. The oxidation of Fe(II) with SO2/air is several orders of magnitude faster than with air alone; rates of up to ?20 g/L'h were observed at 25°C. The reaction proceeds via an intermediate orange-red mixed-valence Fe(II)/Fe(III) sulfite complex, which is present at an essentially constant concentration throughout most of the oxidation process. The oxidation rate of Fe(II) is approximated by the formula -d[Fe(II)]/dt = k [S(IV)] [02]0'3. The concentration of the mixed-valence complex, and thus the iron oxidation rate, decreases with increasing acidity. Certain impurities, such as SCN- and thiourea, negatively affect the rate. The oxidation reaction 2Fe2 + SO2 + 02 4 2Fe3+ + S042- is accompanied by the side reaction H20 + SO2 + 1/202 4 H2SO4. The side reaction becomes particularly important at low temperatures and whenever the oxygen mass transfer is insufficient with respect to the rate of addition of S(IV). Thus, effective oxygen mass transfer is essential for achieving high oxidation rates with minimal acid formation. The activation energy was estimated as 141 kJ/mol over the temperature range 10-35°C.

Jan 1, 2006

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By S. Broda

Waste rock piles (WRP) are made of heterogeneous, coarse grained waste rock, with inclined layers due to segregation along the slopes and haul traffic compacted layers, creating highly contrasted hydrogeological conditions. The internal structure of the pile has a major impact on water and oxygen movement and pore water pressure distribution. In the presence of reactive minerals, this influences the production of acid mine drainage (AMD) or contaminated neutral drainage (CND) with metal leaching from the WRP. Water flow and distribution may also affect slope stability, particularly following major infiltration events (rain/snow melts).The prediction and interpretation of water distribution in WRP is a challenging problem. Numerous numerical investigations of short and long term forecasts have been conducted, and many of these were found of limited reliability. The shortcomings of existing approaches are typically due to difficulties in representing preferential flow processes in macropores. Such phenomena are in fact often neglected in the assessment of water flow in WRP because these are unattainable with the classical porous media approach typically used in this field. This paper focuses on the use of modeling techniques originally designed for massive fractured rock media to simulate flow in WRP. Waste rock properties used in this study are retrieved from large scale laboratory permeability and water retention tests and from in situ infiltration tests. The effect of WRP configurations on water flow into potentially reactive zones is examined with the numerical 3D fully-integrated surface/subsurface, variably saturated flow model HydroGeoSphere. Material properties retrieved from the laboratory tests are represented by means of stochastic facies distribution generated within a probability framework. Modelled soil water contents and hydraulic head distributions, as well as fluxes within a simple waste rock pile, with compacted layers, are compared with results retrieved from simulations based on the classical equivalent porous medium approach. Results indicate significantly increased flow towards the looser waste rock zone by considering heterogeneous material distribution, causing weak or absent capillary barriers and preferential flow paths. Practical implications for the design of waste rock piles are also discussed.

Aug 1, 2013

By Claude Bazin

The Quebec province in Canada is a major producer of aluminium through electrolysis of alumina. The alumina that feeds the electrolysis cells is mainly imported from foreign countries, where it is extracted from bauxite. Other alumina sources, such as clays, have sometimes been considered as potential substitutes for bauxite. There is a large clay deposit in the area of Murdochville in Quebec, with sulfuric acid and electricity available nearby the orebody, as well as sea port facilities leading to the major aluminium plants in Quebec. These are favorable factors to assess the economics of an industrial plant to produce alumina from clays. This paper reviews some of the processes considered for the extraction of alumina from clays and presents results of the initial work carried out on the clay available from Murdochville.

May 1, 2001

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

"A growing public awareness of work-related diseases such as pneumoconiosis and the impact of this awareness on legislative bodies and on the skilled labour market are reasons why the Canadian mining industry must consider dust control of top-drawer importance. Measurements and standards related to the hazard are necessary to control a dust situation and to avoid excessive risk. The author discusses some of the methods of measurement, standards proposed and terminology used in this developing technology. The purpose primarily is to give a better understanding of the basic advances achieved by those who have applied current knowledge with a measure of success."

Jan 1, 1972