Search Documents

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By Brian Rausch

Agenda ?? Refresher: Victor Project Execution ?? Operations Capability roadmap: ? Operations staffing starter group: design participation ? Operations staffing build up for production start-up ? Training and commissioning integration ? Turning OPSCAP ramp-up into a project ?? Go Live! The Results

May 1, 2009

By Paul-Henri Girard

La Mine Agnico-Eagle division Laronde situé à Cadillac, est un producteur d?or, d?argent, de cuivre et de zinc. Cette propriété est situé dans les cantons Bousquet-Cadillac le long d?une des ceintures géologiques les plus productives au monde. La mine Laronde a débuté la production en octobre 1988 à un rythme de 1360 tonnes par jour. Ensuite, elle a augmenté son rythme de production successivement à 1800 TPJ en 1990, 3300 TPJ en janvier 2000 et 4500 TPJ en octobre 2000. Agnico-Eagle, fondé par feu Paul Penna, a toujours eu comme politique la participation des employés aux décisions de la compagnie pour le déveleppement de celle-ci. Cet écrit va permettre de mieux comprendre la façon dont la division fût développé.

May 1, 2001

By T. I. Urbancic, C-I. Trifu

"ABSTRACTSeveral case studies are presented on the use of seismic techniques to map active structures, evaluate changes in stress levels, and identify the conditions leading to large magnitude seismic events and the generation of rock-bursts in Canadian mines. The results suggest that microseismicity can be used to identify the orientation of active fractures; define regions of relatively high and low stress, and those most likely to host a rockburst; determine the role of local stress on observed shear failures; and identify the path of stress transfer associated with the remote triggering of rockbursts. Additionally, the conditions leading to rock-bursts can be characterized by a significant increase in the clustering of microseismic events along the fault plane orientation of an impending event, and an increase in the effective stress levels. It is concluded that the analysis of microseismicity provides the means for remotely monitoring rock mass behaviour as a result of mining."

Jan 1, 1997

By Stanley W. Holmes

"The discovery of extensive uranium mineralization on the Pronto property in April 1953 initiated a program of staking, exploration, and development unparalleled in Canadian mining history. Within twelve months of the discovery hole, sufficient ore had been blocked out to merit a 55-million-dollar contract with Eldorado Mining & Refining Co. On October 15, 1955, two years and four months after discovery, Pronto went into production with a mill rated at 1,000 to 1,500 tons per day. The property is on the southern edge of the Algoma uranium district, 10 miles east of the town of Blind River and close to the Canadian Pacific Railway and Highway 17. Docking facilities for Great Lakes steamers are avail-able at Spragge, 4 miles to the east.The data and conclusions presented in this paper are based on field studies, drill hole information, and underground development. The ideas of ore genesis are those of the writer, and will undoubtedly be modified as more detailed studies and research are carried out. Because of security regulations, information pertaining to grade and tonnage will not be discussed.GeologyThe general geology of the Algoma basin has been outlined in a pre-ceding paper (Joubin and James). The description below is concerned essentially with the rocks most closely associated with the Pronto deposit. They may be grouped in three structural and lithological units: (1) the pre-Huronian basement, (2) the Mississagi formation, the lowest member of the Huronian sediments lying unconformably on the basement, and (3) a series of basic intrusives cutting (I) and (2). Most of the uranium mineralization occurs in a quartz-pebble conglomerate forming the basal member of the Mississagi quartzite."

Jan 1, 1949

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By J. H. Parliament

"The 15,000-tpd Similkameen open-pit copper mine, 10 miles south of Princeton, B.C., started production during 1972. The two main ore zones are separated by the deep canyon of the Similkameen River, with the Ingerbelle or western deposit being mined first. The location, design and construction of the plant were complicated by the steep terrain and the situation of the orebodies. Mining, utilizing 10-cu.yd electric shovels and 100-ton electric-wheel trucks, is conventional. Closely integrated with the preproduction mining was the construction of a 4-mile section of main highway to bypass the Ingerbelle pit. This entailed a very large fill, placed with mine equipment. Ore is crushed to minus 9 inches, stockpiled and reclaimed for direct delivery to three 32-ft-diameter by 14• ft single-stage autogenous grinding mills, each driven by two 4000-hp motors. Because of the friable ore in the upper part of the mine, 4-inch balls are added, with higher than design throughput attained. Classification is by 91>-inch spiral classifiers and cyclones. The flotation section comprises three parallel lines of ten 400-cu.ft rougher- scavenger cells and a single line of 100-cu.ft cleaner and recleaner cells. Concentrate is transported in end dump, closed trucks to Vancouver for dockside storage prior to shipment to the smelter. Tailings are piped across the canyon on a suspension bridge and through a tunnel to an empoundment area. Water is reclaimed and returned to the concentrator, forming a closed system. Dams are raised with cycloned ands, with the downstream section compacted."

Jan 1, 1973

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By Mike Smith, George Chung

"A 23 million dollar Flotation Plant has been commissioned at the Iron Ore Company of Canada in 1998. Nine OK-50 cells &re used to float silica in this 1,400 tomes per hour plant. The paper details project development, construction and operating results. This plant gives IOC the capability to produce not only high quality blast furnace pellets of varying silica, CaO and MgO levels, but also a high iron, DR grade pellet. The first activity was simply to sit down with the suppliers, Outokumpu, Wemco. GL&V and Svedala, to discuss applications and share experiences. We learnt what each supplier had to offer, what features would particularly suit this application, what options were offered, what were the materials of construction, how the equipment is maintained, which wear parts require replacement, etc., etc. We tried to learn as much about the equipment as the suppliers themselves knew. Then we tried to learn more: we contacted users and asked about any weak points, which options were worth incorporating and which items were not. We then discussed these points with the suppliers and established how potential problems might be overcome."

Jan 1, 1999

By K. Murase

Potentiostatic electrodeposition behavior of dendritic copper from acidic copper(I) chloride (cuprous chloride) baths containing sodium chloride and sodium bromide was investigated. The morphology, or appearance, of copper dendrite and the sodium content in the dendrite as an impurity were both influenced by deposition potential (0 to ?150 mV vs. SHE) and bath temperature (R.T. to 60 C), while the current efficiency for the deposition was 99% or more irrespective of the deposition conditions examined. The bath pH did not affect the deposition behavior in the pH range of 0 to 2. Bath temperature was found to be the most important factor influencing the deposition current. The current density of the dendrite deposition on a titanium cathode was lower than that onto a copper cathode with the same substrate surface area. The reproducibility of the current for the dendrite deposition was poorer when an as-polished titanium cathode was used, although it was improved by surface treatment of the cathode with an HF-HNO3-H3PO4 solution before electrodeposition. The deposition behaviors were discussed with the potential-pH diagram of the Cu-Cl-H2O system.

Jan 1, 2007

By E. M. Córdoba

The effect of the Fe3+ lFe2+ redox couple on the chemical and biological dissolution of chalcopyrite was studied. All the tests were carried out in stirred flasks with 100 mL of a ferric/ferrous sulphate solution, in the absence or in the presence of bacteria (iron- or sulphur-oxidizing) and at low (35 DC) and high (68DC) temperature. The initial redox potential was controlled between 300 and 600 m V Ag/ AgCI and silver was used as chemical catalyst. The results showed that the oxidizing action of ferric ion on the chalcopyrite was controlled, in all cases, by nucleation and precipitation of jarosites on unreacted particles. The tendency of Fe3+lFe2+ solutions towards equilibrium favours the activities of both ions to be equal. Consequently, the dissolution rate was faster at relatively low redox potentials (between 400 and 500 mY) than at high values (600 mY). In this sense, the presence of ferrous ion in the system is a key factor to control hydrolysis and precipitation of ferric ion. Unlike jarosite, the elemental sulphur produced during dissolution of chalcopyrite was porous and did not act as a diffusion barrier.

Jan 1, 2007

By Lopatka. M. J.

This paper presents the results of 3 tons skid steer 6x6 wheel robot drive system field tests. The aim of the investigation was verification of assumed data for drivetrain diesain and forces identification in the drivetrain system during maneuvering and crossing obstacles. Robot has hydraulics drive system with motors in the wheels and hydraulic suspension system. The neded drive torque on wheels was determined by pressure measurnig on motors.

Aug 1, 2013

By Karl J. C. Harries

"2.1. INTRODUCTIONNo agreement can be perfect in the sense that it contemplates and provides for all eventualities. Mineral acquisition agreements are usually negotiated and drafted at a time when an orebody is no more than a gleam in a geologist’s eye, so it is hardly possible to provide for development and operation in other than the most general terms. However, an agreement that stops short of contemplating the possibility of an orebody and production is ill-advised. Accordingly, it is important to provide procedures to make decisions that will let the project proceed, even in the face of a fallingout between parties. Whether the parties are shareholders in a corporation or venturers in a contractual common undertaking like a joint venture, differences of opinion and disputes will occur. Unfortunately, more and more are ending up before the courts. Besides greed and the growing tendency in society to fight rather than talk, there are other factors that contribute to the increase of litigation. In some jurisdictions, agreements have tended to become complicated, often defying interpretation, even by a lawyer, and explorationists want their budgets to go into the ground as constructive work rather than into a lawyer’s pocket. All this has led to a growing tendency for corporations to take the attitude that the chances of finding a mine are, at best, marginal and there are lots of earlier agreements in the files to draw from, so why not prepare their own agreements? As discussed in the preceding chapter, this can be folly. All these factors can quickly have parties facing each other in court while a project sits idle. Added to this is the problem that, in some jurisdictions, lawyers may take cases on a contingency-fee basis, sometimes promoting the pursuit of a nebulous claim.When an orebody is discovered, someone will always want some, or more, for himself. There is a breed of “prospectors” who prospect for legal actions, on the somewhat sound grounds that a major corporation will buy off nuisance litigation, rather than incurring the cost and effort of attacking even a poorly founded claim in the courts. They may even find a winner. Besides, it is far more comfortable and relaxing to prospect for problems and legal niceties than to prospect for an orebody.1 In short, it is appropriate to consider briefly some of the factors relating to lawsuits and judgments. Although many of the comments are made in the context of the common law and the Canadian legal system, most of the concepts and suggestions are applicable to any legal system."

Jan 1, 2003

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester&apos;s suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999