Search Documents

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By Ree Llewellyn

"It has been estimated conservatively that the costs of wear damage and friction in the Canadian mining and mineral processing industry amount to over one billion dollars per year. These are mainly incurred through the repair or replacement of worn parts and production losses from related equipment downtime. The selection and application of the most appropriate wear protection components and systems, can thus have a very significant influence on productivity, profitability and global competitiveness.Details are presented of the wide diversity of materials used to counteract the varied and often complex wear attack mechanisms that occur in surface mining. The majority are various forms of steels and irons with generally very high hardness. However, they also include relatively soft elastomers and polymeric products.The main characteristics and applications of the different classes are reviewed. Case studies record significant performance improvements achieved through more judicious selections. Finally, some new developments which reduce maintenance charges by substantially increasing wear component life, are described."

Jan 1, 1996

By John L. Mero

"The ocean has served humanity as a source of raw materials for thousands of years, but only on a minimal scale relative to its potential. Exploration programs have shown the ocean to contain a large number of mineral deposits of great extent and attractive grade. Recent research has indicated that a number of these deposits can be economically exploited with present-day technology and that the cost of winning many industrially important minerals from the oceanic deposits is potentially much less than that of winning similar minerals from land deposits. Although the finding of mineral deposits in the sea is a relatively simple matter at the present time, the exploitation of many of these deposits has lagged due to the lack of the availability of specific mining techniques for the individual deposits. Within the past two years, however, several developments have taken place in the design and testing of ocean mining systems in depths of water as great as 12,000 feet which indicate that the problem of mining in the ocean may soon be solved.Within the next decade, the ocean should prove to be a major source of many minerals for society and should come to dominate as a source of such metals as copper, nickel, cobalt, manganese, etc. Within a few years of the initiation of the mining of the deep-sea metalliferous nodules, land sources of such metals as nickel, cobalt, copper, manganese, etc. will be seriously affected and it is conceivable that the present structure of the world mining industry will undergo a substantial change in character."

Jan 1, 1972

By G. H. Blackwell

Open pit mine management must ensure that sufficient trucks are available and are being used effectively for production, and that operating costs are under continued control and review for improvements. This paper describes methods for estimating truck fleet requirements which have been used effectively at large- and medium-sized open pit mining operations. Applied to commonly available data, multiple regression analyses can indicate when mine plans should be revised toward optimizing the number of trucks required. Prediction of major cost items for budgetary purposes is addressed, along with an example of how readily available production data can be used to reduce costs systematically.

Jan 1, 1999

By R. J. Allan

"CANADA HAS A GREATER LAKE AREA than any other country. Discountin the Great Lakes, this fresh-water area, mainly in the Canadian Shield, is listed as approximately 300,000 sq. mi. Densities of lakes range up to 7,500 in a 5,294-sq. mi. area of the Shield, southwest of Reindeer Lake, Saskatchewan. Five areas chosen randomly from the Shield (Figure 1) contained sufficient lakes to provide samples at a density of at least one per 10 sq. mi. Regional geochemical surveys in the Appalachian area (Nova Scotia, Boyle et al., 1958; New Brunswick, Boyle et al., 1966) and in the Cordilleran area (Yukon, Gleeson, 1965) of Canada and in many other areas of the world have relied heavily on analyses of stream sediments. These surveys show that sampling of material related to the drainage system reflects the over-all trace element content of the rocks and surficial deposits in the drainage basin. In the Shield, the classic types of dendritic (and other) stream systems found elsewhere in the world are very rare. However, impeded and disorganized stream systems that abound with lakes can provide the exploration geochemist with an ideal composite drainage system sample in the form of lake sediment. This paper attempts to demonstrate the feasibility of, and review the theory and problems involved in, the use of lake sediment as a regional geochemical exploration medium. Most of the references to field examples are taken from a regional survey using lake bottom sediment as the sample medium over 1,500 sq. mi of the Coppermine basalt group and adjacent rocks (Figure 2). During this regional survey, detailed sampling of several lakes was carried out and the results are referred to at appropriate places in the text."

Jan 1, 1971

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By D. C. Fraser

Copper occurs invisibly in a geo-logical environment characterized by swampy conditions and an accumulation of forest peat. This swamp, located in southeastern New Brunswick, contains up to ten per cent cop-per (dry weight), in the organic sediments. This occurrence appears unique in that the metal is apparently organically combined in a chelate compound. Unlike the acidic nature of most peat bogs, the pH of the cup-riferous peat is nearly neutral. Analyses of the peat and associated soils have indicated that the bulk of the copper is contained in the organic sediments. It appears that the cop-per distribution is affected by capillarity, evaporation and the growth of frost crystals, and that the copper fixation is effected by organic sequestration resulting in the metal being bound to the nitrogen or oxygen components of the forest peat. While such a fixation mechanism is not definitely established as responsible for the immobilization of the metal, the facts at hand are compatible with

Jan 1, 1961

By J. F. Davis

Pegmatite dykes containing lithium minerals and beryl occur dose to the borders of intrusive masses of granitic rock in the Winnipeg River area of Manitoba. Both vertical and flat-lying dykes are present. Most of the pegmatites consist of zones, containing characteristic mineral assemblages, arranged more or Jess parallel to the borders of the dykes. Five important lithium minerals are present; each occurs in a separate zone, but all the lithium-bearing zones are situated toward the centres of the pegmatites. Spodumene is the most abundant and widespread of the lithium minerals and occurs as small crystals intimately intergrown with quartz. Beryl is not an important constituent of the lithium pegmatites, but when .present, occurs outside the lithium zones, toward the margins of the -dykes. Beryl is most common in dykes containing few or no lithium minerals. The mineral assemblage in the beryl zone of the lithium dykes is the same as that of the beryl dykes. The attitude and internal structure, particularly zoning, of the pegmatite dykes, and the texture and assemblages of the constituent minerals, have an important bearing on exploration, development, and mining of these pegmatites, and on the extraction of various mineral products from them.

Jan 1, 1958

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By H. -L. Heikkilä, E. Peuraniemi

"Boliden Harjavalta Oy has a long tradition in the Finnish metal industry starting from the 1930's. The Smelter consists of copper and nickel flash smelting lines. Off-gases are captured in the acid plant to produce sulfur products. During the early years of production, the surrounding environment suffered from high SO2 and dust emissions. The first acid plant started in 1947, a few years after commissioning of the smelter. The flash smelting method was developed and commissioned in 1949. This created the basis for today’s environmentally sound metal production. Recent air emission reductions are related to treating lean ventilation and granulation gases. Emissions from the stacks are monitored with continuous measurement devices. SO2 and PM10 concentrations are also measured from the residential area and reported online in cooperation with Harjavalta community and other local industry.INTRODUCTIONProductionBoliden Harjavalta Oy smelts copper and nickel concentrates and refines copper in the western part of Finland. The copper concentrates come from external copper mines mainly in South America and Europe. Concentrates are unloaded at the Pori harbor and transported to Harjavalta by train from a distance of about 60 km. Boliden Harjavalta Oy has operations in Harjavalta and Pori. The smelter in Harjavalta produces copper anodes that are transported via railway to the copper refinery in Pori. The anodes are electro-refined into copper cathodes and by-products like Se, Ag, Au and Pt/Pd concentrate. In the Harjavalta smelter SO2 containing gases are delivered to a sulphuric acid plant where sulphuric acid and liquid sulphur dioxide are produced.Our nickel smelter smelts nickel concentrates on a tolling basis to produce nickel matte for customer needs. SO2 containing off-gases are delivered to the sulphuric acid plant for sulphur capture and modification into products.All our operations are certified according to the Quality, Environmental and Occupational Health and Safety Standards ISO 9001, ISO 14001 and OHSAS 18001. Boliden Harjavalta Oy was the first company in Finland operating in the metal and technology industry to be certified according to the Energy Management Standard EN 16001, currently this certification is done according to ISO 50001."

Jan 1, 2012

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932